Description : As shown in the illustrations, most console schematic diagram sheets have letters and/or numbers placed across the top and numbers along the side boarders. The purpose of these markings is to ... small hole over a letter and number, what month and year that particular page was redrawn
Last Answer : Answer: A
Description : Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1
Last Answer : 0.015 mm s-1
Description : A structure is erected on an impervious clay whose thickness is 12 m. Drainage is possible both at upper and lower surfaces. Coefficient of consolidation is 0.015 cm2 per minute. For attaining 50% consolidation with a ... 20, the number of days required (A) 3233 (B) 3123 (C) 33331 (D) 3313
Last Answer : Answer: Option C
Description : How do i round .0099 to the nearest hundreths?
Last Answer : 0.01
Description : As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential
Last Answer : Answer: B
Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad
Description : In order to decrease the resistance of the 50K pot located at '21Q/R' shown in the illustration, the wiper of the actual component must be moved ____________. EL-0099 A. to the left B. to the right C. clockwise D. counterclockwise
Last Answer : Answer: D
Description : The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.
Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above
Last Answer : Answer: C
Description : Pin #8 of the astern valve position sensor shown in the illustration is connected _______________. EL-0099 A. to analog common B. in series with PCOM C. to (-) 50 volts D.C. D. to (+) 50 volts D.C.
Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'
Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Description : What does the arrangement at coordinates '62E' shown in the illustration represent? EL-0099 A. Position recording drum and stylus B. Temperature compensating thyristor C. Miniature bridge rectifier D. Twisted wire pair within a shield
Description : What do the arrow-like symbols at coordinate '33J' shown in the illustration represent? EL-0099 A. Connection to ground. B. Connection to the analog common bus. C. Plug-in connection. D. Screw connection on a terminal board.
Description : Pin #6 of the ahead valve position sensor as shown in the illustration is connected _______________. EL-0099 A. to (-) 50 volts D.C. B. in parallel with PCOM C. to (+) 50 volts D.C. D. to analog common
Description : As shown in the illustrations of console schematic diagrams, each circuit card and component, such as a relay or indicating lamp, has an identifier attached. This identifier, which is composed of ... where the item may actually be found on the console by section, surface and possible subassembly
Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?
Last Answer : 10001/999900
Description : what is bigger 0.015 or 0.01?
Last Answer : 0.015 > 0.010
Description : How could you find the y-coordinate of the midpoint of a vertical line segment with endpoint at (00) and (015)?
Last Answer : If you mean endpoints of (0, 0) and (0, 15) then the midpoint isat (0, 7.5)
Description : What is 015 treas 310 misc pay?
Last Answer : Teaaaaa
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 1.74 ohms the current will be _______. EL-0018 A. 66.09 amps B. 116.74 amps C. .026 amps D. .015 amps
Description : Percentage of the heavy water in ordinary water is around (A) 0.015 (B) 7.54 (C) 0.71 (D) 32.97
Last Answer : (A) 0.015
Description : Percentage of heavy water in ordinary water is around (A) 0.015 (B) 7.54 (C) 0.71 (D) 32.97
Description : Percentage of U-238 in natural uranium is around (A) 0.71 (B) 99.29 (C) 0.015 (D) 29.71
Last Answer : (B) 99.29
Description : Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505 (D) 0.805
Last Answer : (B) 0.055
Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m
Last Answer : (D) 0.060 m
Description : Natural water contains approximately __________ percent of heavy water. (A) 0.015 (B) 0.71 (C) 1.2 (D) 3.5
Last Answer : A) 0.015
Description : Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505
Last Answer : Option A