State the need for filter circuits in power supply.

State the need for filter circuits in power supply.
by

1 Answer

Answer :

Ripple must be kept away from the load and it should be removed from the rectified output. Therefore , there is a necessity of filter circuit for removing i.e. smoothing or filtering the ripple and allowing the (pure or steady) d.c. voltage to reach the load.
by

Related questions

Define filter. State its types. Draw any one filter with input and output waveform.

Description : Define filter. State its types. Draw any one filter with input and output waveform.

Last Answer : Defination : Filter is a circuit which remove or filtered out the AC component (ripple) Types of filter 1. Shunt Capacitor filter (C filter) 2. Series Inductor filter (L filter) 3. LC filter 4. filter (CLC filter) Shunt Capacitor filter (C filter) OR Waveforms:

Draw and describe power triangle. State its significance.

Description : Draw and describe power triangle. State its significance.

Last Answer :  Power Triangle:   OR   Power Triangle is a right angled triangle whose sides represent the active, reactive and apparent power. It is obtained by multiplying the circuit current I ... loss due to different load. This is very important for designing the energy efficient electrical system. 

Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Description : Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Last Answer : Construction of BJT (NPN): Working of NPN Transistor : The circuit diagram of the NPN transistor is shown in the figure below. The forward biased is applied across the emitter-base ... Zero with input current is Zero transistor in cut off. In this region transistor act as open switch

State the different types of transformers. Describe the construction and general principle of transformer.

Description : State the different types of transformers. Describe the construction and general principle of transformer.

Last Answer : Different types of transformer are core type shell type Berry type Construction of transformer: OR Shell Type construction can be consider for diagram Transformer ... is based on the principle of mutual induction between two circuits linked by a common magnetic field. 

Write the Emf equation of transformer. State the meaning of each term in it.

Description : Write the Emf equation of transformer. State the meaning of each term in it. 

Last Answer : EMF equation of Transformer:- E1 = 4.44 f ØmN1 OR E1 = 4.44 f BmAN1 E2 = 4.44 f ØmN2 OR E2 = 4.44 f Bm AN2 Let, E1 = Primary emf E2 = Secondary emf N1= Number of turns in the primary N2 ... flux in core (wb) Bm= Flux density (wb/m2 /Tesla) A= Area of cross section of core m2 F = Frequency 

State applications of single phase AC motors.

Description : State applications of single phase AC motors. 

Last Answer : Water pumps ceiling fan & air conditioners. lathe machine washing machines. Blowers Mixers & grinders Compressors Conveyers Refrigerators.

State Lenz’s law.

Description : State Lenz’s law.

Last Answer : Lenz’s Law: It states that the direction of electromagnetically induced emf is such that it always opposes the main cause of its production. Or It is expressed by equation E = - N (dΦ/dt) volts Where – sign indicate the direction EMF is induced opposite to rate of change of flux. 

Draw the diagram of transistor operating regions

Description : Draw the diagram of transistor operating regions

Last Answer : diagram of transistor operating regions

Explain the working of Half wave rectifier with suitable diagram

Description : Explain the working of Half wave rectifier with suitable diagram

Last Answer : The half-wave rectifier circuit using a semiconductor diode (D) with a load resistance RL but no smoothing filter is given in the figure. The diode is connected in series with the secondary of the ... . Since only half-cycles of the input wave are used, it is called a half wave rectifier. 

Explain with neat diagram how transistor can be used as a switch.

Description : Explain with neat diagram how transistor can be used as a switch.

Last Answer : In Bipolar Transistor as a Switch the biasing of the transistor, either NPN or PNP is arranged to operate the transistor at both sides of the I-V characteristics curves. The areas ... possible and maximum current flowing through the transistor. Therefore the transistor is switched Fully-ON .

Explain Zener diode as voltage regulator.

Description : Explain Zener diode as voltage regulator. 

Last Answer : Zener Diodes can be used to produce a stabilised voltage output with low ripple under varying load current conditions. By passing a small current through the diode from a voltage source, via a ... across the load in spite of variations in the input voltage or changes in the load current. 

Explain the construction details of LED

Description : Explain the construction details of LED

Last Answer : The construction of LED differs from normal standard diode in many aspects. As shown in the figure the p-n junction of the LED bulb is enclosed by a transparent, hard plastic epoxy resin hemispherical- ... that much light. Due to this, the brightest light will be emitted at the top of the LED.

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

(i) Discuss ideal and practical voltage source (ii) Compare CB, CC and CE configuration

Description : (i) Discuss ideal and practical voltage source (ii) Compare CB, CC and CE configuration

Last Answer : (i) Discuss ideal and practical voltage source Ideal voltage source The ideal voltage source has a constant voltage across its terminal, irrespective of the current drawn from the source. Ideal Voltage Source have zero ... to reduce. (ii) Compare CB, CC and CE configuration

(i) Draw the time domain and frequency domain representation of sine wave and triangular wave. (ii) Define frequency and wavelength.

Description : (i) Draw the time domain and frequency domain representation of sine wave and triangular wave. (ii) Define frequency and wavelength.

Last Answer : (i)Time domain and frequency domain representation of sine wave time domain and frequency domain representation of triangular wave.   ii) Define frequency and wavelength. Frequency ... : Wavelength can be defined as the distance between two successive crests troughs of a wave. 

Describe the operation of transistor as a switch with suitable diagram.

Description : Describe the operation of transistor as a switch with suitable diagram.

Last Answer : In Bipolar Transistor as a Switch the biasing of the transistor, either NPN or PNP is arranged to operate the transistor at both sides of the I-V characteristics curves. The areas of operation for a transistor ... . OR Open switch Table indicating transistor as switch

Compare between active and passive components.

Description : Compare between active and passive components.

Last Answer : active component passive component  It is a device which amplify by producing an output signal with more power in it than that of input signal It is a device which ... bidirectional function semiconductor materials are used Non-semiconductor or semiconductor material is used

Define the following with respect to BJT. (i) Input resistance (ii) Output resistance

Description : Define the following with respect to BJT. (i) Input resistance (ii) Output resistance

Last Answer : Input resistance: It is the ratio of small change in emitter -to-base voltage(∆VEB) to the resulting change in emitter current (∆IE) for a constant collector to base voltage(VCB) ... of BJT is ratio of voltage between output terminal and common terminal to current through output terminal. 

Define α. Give the relationship between α and β.

Description : Define α. Give the relationship between α and β.

Last Answer : Alpha (α )– It is ratio of collector current IC to emitter current IE of a transistor.

Define active components. Give two examples.

Description : Define active components. Give two examples. 

Last Answer : The component which requires power supply for its operation is called as Active component. e.g. Diode, Transistor, ICs, SCRs. OR Active Component: The component which rely on source of ... is called active component example diode , transistor, FET, and so on. They are semiconductor component

Describe the construction and working principle of single phase AC motor.

Description : Describe the construction and working principle of single phase AC motor.

Last Answer : construction and working principle of single phase AC motor : Single phase induction motors have a phase distributed winding on the stator and a squirrel cage short-circuited winding on the rotor. ... is the basic working principle of induction motor of either type, single phase of 3 phase.

Describe the operation of inductor with sinusoidal AC voltage as input. Draw waveform for voltage across and current through the inductor. Draw its phasor representation.

Description : Describe the operation of inductor with sinusoidal AC voltage as input. Draw waveform for voltage across and current through the inductor. Draw its phasor representation.

Last Answer : An alternating voltage is applied to a purely inductive coil, a back e.m.f. is produced due to self-inductance of the coil. The back e.m.f. at every step, opposes the rise of fall of current through the coil ... drop, the applied voltage has to overcome this self induced e.m.f. only.

Describe the construction and working principle of auto transformer.

Description : Describe the construction and working principle of auto transformer.

Last Answer : An auto transformer has single winding which is used as primary and secondary winding. This winding is wound on laminated enameled magnetic core.   OR   As shown in fig. 1 the input is ... this construction we can step up the voltage. So this transformer known as step up autotransformer.  

Define- (i) Current (ii) Potential difference

Description : Define- (i) Current (ii) Potential difference

Last Answer : i) Current :- electric current is defined as the movement of electronics or flow of electronics inside the conducting material. Unit-ampere(A)  ii) Potential Difference: The difference between the ... the electrical circuit is known as potential difference between those points. Unit:- volt (V) 

Define RMS value and Average value of AC waveform.

Description : Define RMS value and Average value of AC waveform.

Last Answer : 1. RMS value:- For an alternating current, the RMS value is defined as that value of steady current (DC) which produces the same heat or power as is produced by the alternating current during the ... by averaging all the instantaneous values of its wave over a period of half cycle. Iav=0.637 Imax

Define self induced Emf. Write equation of self induced Emf.

Description : Define self induced Emf. Write equation of self induced Emf. 

Last Answer : Definition: Self-induced emf is the e.m.f induced in the coil due to the change of flux produced by linking it with its own turns. Or Self induced emf is that which is induced in a coil, due to the change in its own current or flux. Self induced emf equation. E = - N (dΦ/dt) volts

Explain with circuit diagram operation of zener diode as a voltage regulator.

Description : Explain with circuit diagram operation of zener diode as a voltage regulator.

Last Answer : The function of a regulator is to provide a constant output voltage to a load connected in parallel with it in spite of the ripples in the supply voltage or the variation in the load ... V0 = VZ is obtained across RL, whenever the input voltage remains within a minimum and maximum voltage.

State the necessity of rectifier and filter circuits.

Description : State the necessity of rectifier and filter circuits.

Last Answer : Need of Rectifiers: Many electronic devices and circuits work on DC. It is then needed to convert A.C. into D.C. Rectifier is the best and cheapest way to provide D.C. for electronic devices. ... moved from the pulsating D.C. to obtain pure D.C. signal. To remove this filter circuit is used. 

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

What are the types of filter circuits?

Description : What are the types of filter circuits?

Last Answer : The types of filter circuits are Inductor filter Capacitor filter LC filter CLC or π filter

Why is the use of large value capacitors in filter circuits discouraged?

Description : Why is the use of large value capacitors in filter circuits discouraged?

Last Answer : Expense

Why is the use of large value capacitors in filter circuits discouraged?

Description : Why is the use of large value capacitors in filter circuits discouraged?

Last Answer : Expense

Which capacitors are suitable for DC filter circuits?

Description : Which capacitors are suitable for DC filter circuits?

Last Answer : Electrolytic capacitors are suitable for DC filter circuits.

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Description : Capacitors are used on the output of the power supply in today's consoles to _____________. A. filter out 'ripple' B. prevent overloads C. act as a permanent load D. decrease the average value of the output voltage

Last Answer : Answer: A

If the output filter capacitor in a power supply actually had a value twice its stated value, which of the

Description : If the output filter capacitor in a power supply actually had a value twice its stated value, which of the following symptoms would be found?   a. The output voltage would be doubled and a small ... would be greater than expected.  d. The output and ripple voltage would be less than expected.

Last Answer : b. The ripple voltage would be half of what is expected and a small increase in the output voltage would be detected. 

Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Description : Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting ... the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Last Answer : Answer: D

The supply both to field and armature circuits are disconnected simultaneously in a separately excited dc...

Description : The supply both to field and armature circuits are disconnected simultaneously in a separately excited dc motor and it comes to a standstill in 5 sec. If the armature circuit of this motor is disconnected from supply with field ... rest in (1) 5 sec (2) 7 sec (3) 4 sec (4) A very long time  

Last Answer : 5 sec only.standstill time doesn't depend upon field excitation

State different types of power in ac circuits. Write the expression and units for the same. Draw the power triangle.

Description : State different types of power in ac circuits. Write the expression and units for the same. Draw the power triangle. 

Last Answer : i) Active Power (P):- The active power is defined as the average power Pavg taken by or consumed by the given circuit.   ii) Reactive Power (Q):-  The reactive power is defined as the product of ... values of voltage (v) and current (I) it is given by    iv) Power Triangle: 

State the need of Rectifier circuits.

Description : State the need of Rectifier circuits.

Last Answer : The DC power supply is essential for operation of many electronic devices and circuits.This DC voltage is obtained from AC source.Rectifier circuit is important circuit for this conversion.

State the need of tuned amplifier in electronic circuits.

Description : State the need of tuned amplifier in electronic circuits.

Last Answer : Necessity of tuned amplifier: 1. Selection of the desired radio frequency signal. 2. Amplification of the selected signal to a selected voltage level.

Help boosting this circuits power?

Description : Help boosting this circuits power?

Last Answer : Out of curiosity, why do you need 400v DC? You could possibly use a transformer for that purpose since you probably won’t find any (cheap) capacitors with a 400v tolerance.

Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions properly and trips generator #1 electrically off the bo A. Start the emergency generator. B. Ascertain cause of the low lube oil pressure. C. Strip the board of all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Description : Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions ... all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Last Answer : Answer: C

The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Description : The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Last Answer : Answer: A

Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. C. Inductive reactance varies directly with the frequency and the inductance. D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency controllers D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Description : Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency ... D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Last Answer : Answer: D

Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Description : Handheld phase sequence indicators are useful when ________. A. preparing to parallel alternators B. connecting lighting branch circuits C. troubleshooting DC motors D. connecting shore power lines to the ship

Last Answer : Answer: D

The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Description : The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Last Answer : Answer: D

To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection

Description : RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection

Last Answer : Answer: B