Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component?  A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.
by

1 Answer

Answer :

Answer: D
by

Related questions

When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Description : When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Last Answer : Answer: D

Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel C. the resistor banks are composed of individual series-connected units D. there are separate switches for the motor and the control

Description : Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel ... individual series-connected units D. there are separate switches for the motor and the control

Last Answer : Answer: B

When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment away. B. Measure capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Description : When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment ... capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Last Answer : Answer: C

Motor controllers are seldom troubled by grounds because ________________. A. cabinet heaters always keep internal components dry B. special insulation is used on wire for vital circuits C. shock mounts on controller panels greatly reduce vibration D. contactors and relays are mounted on nonconducting panels

Description : Motor controllers are seldom troubled by grounds because ________________. A. cabinet heaters always keep internal components dry B. special insulation is used on wire for vital circuits C. ... on controller panels greatly reduce vibration D. contactors and relays are mounted on nonconducting panels

Last Answer : Answer: D

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Description : Before working on an electric cargo winch master switch or controller, you should _____________. A. spray the gasket surface with a solvent B. drain condensate from the box C. open the circuit breaker in the power supply and tag D. heat the switch box to remove any moisture

Last Answer : Answer: C

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Description : When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Last Answer : Answer: B

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

3. What precaution should be taken to avoid the overloading of domestic electric circuits? -Physics-10

Description : 3. What precaution should be taken to avoid the overloading of domestic electric circuits? -Physics-10

Last Answer : A few of the precautions to be taken to avoid the overloading of domestic electric circuits are as follows: Connecting too many devices to a single socket should be avoided Using too many appliances at the same time should be avoided Faulty appliances should not be connected to the circuit

Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Description : Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Last Answer : Answer: C

Explain the uses of safety rubber hand gloves and rubber mats in electrical engineering.

Description : Explain the uses of safety rubber hand gloves and rubber mats in electrical engineering. 

Last Answer : Uses of safety rubber hand gloves in electrical engineering:  * The safety rubber hand gloves are always used for online work to insulate the human body or operator from the electrical supply. * The ... human body) is isolated from ground or earth i.e. why danger of electrical shock is avoided. 

On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Description : On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive overtravel of the pilot valve by the synchronous motor. These devices are called _________________. A. overlap sensors B. limit switches C. overtravel relays D. proximity switches

Last Answer : Answer: B

Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove metallic dust. C. The contact surfaces should be greased to increase contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Description : Which of the following statements is true concerning the cleaning of electrical contacts? A. Compressed air should be used to blow out metallic dust. B. Magnetic brushes should be used to remove ... contact resistance. D. Delicate parts should be cleaned with a brush and an approved safety solvent.

Last Answer : Answer: D

When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Description : When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Last Answer : Answer: B

Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In series with the load and in parallel with the meter movement. C. In parallel with the load and in series with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Description : Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In ... with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Last Answer : Answer: B

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common talking circuit is composed of two ungrounded wires. C. The ringing circuit has two grounded wires connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Description : Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common ... connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Last Answer : Answer: B

Why do Electricians use rubber gloves while working? -Do You Know?

Description : Why do Electricians use rubber gloves while working? -Do You Know?

Last Answer : answer:

Electricians use rubber gloves while working because - (1) rubber is an insulator (2) rubber is a good conductor (3) wearing rubber gloves is mandatory (4) rubber makes work easy

Description : Electricians use rubber gloves while working because - (1) rubber is an insulator (2) rubber is a good conductor (3) wearing rubber gloves is mandatory (4) rubber makes work easy

Last Answer : (1) rubber is an insulator

Why do Electricians use rubber gloves while working?

Description : Why do Electricians use rubber gloves while working?

Last Answer : Rubber is an insulator

What precaution should be taken while removing a current operated relay when the equipment is in service?

Description : What precaution should be taken while removing a current operated relay when the equipment is in service?

Last Answer : Ensure that the CT is not getting opened by shorting the appropriate terminals. (Eventhough the terminals are automatically shorted once relay is removed the above point may carried out to ensure the same) 

A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Description : A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Last Answer : Answer: B

Which of the following statement(s) is/are true concerning carrier proteins? a. Carrier proteins are distinguished by three types of mechanisms: carrier-type, channel-type, and conduction-type b. Conformational changes in the membrane protein occur between the conducting and the nonconducting states c. A channel-type carrier protein has two states—closed and open d. Carrier-type transport proteins are equally accessible from either side of the membrane

Description : Which of the following statement(s) is/are true concerning carrier proteins? a. Carrier proteins are distinguished by three types of mechanisms: carrier-type, channel-type, and conduction-type b. ... and open d. Carrier-type transport proteins are equally accessible from either side of the membrane

Last Answer : Answer: b, c Most transport proteins appear to function as carriers, rather than channels. Important distinctions can be made between types of carrier proteins on the basis of transport kinetics. ... a carrier mechanism, the binding site is available only one side of the membrane at any instant

Mention What Are The Precaution Measures Taken By The Repair And Maintenance Worker At Working Site?

Description : Mention What Are The Precaution Measures Taken By The Repair And Maintenance Worker At Working Site?

Last Answer : The precaution measures taken at the working site is:  Overhead and side clearances are adequate to permit the safe operation of the lift truck  Aisles, floors and passageways should be ... of vapours from the refueling and operation of its lift trucks, workplace should be adequately ventilated.

In the illustration, the component labeled 'G' _________. EL-0031 A. is lined with cardboard to maintain a moisture (electrolyte) barrier between cells B. is a one piece container with compartments for each individual cell C. must be UL approved for shipboard use D. can only contain one cell

Description : In the illustration, the component labeled 'G' _________. EL-0031 A. is lined with cardboard to maintain a moisture (electrolyte) barrier between cells B. is a one piece container with compartments for each individual cell C. must be UL approved for shipboard use D. can only contain one cell

Last Answer : Answer: B

Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board of all non-vital circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Description : Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board ... circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Last Answer : Answer: B

Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

Wire in general, when used aboard vessels must meet minimum requirements. Which of the following statements is/are correct? A. Each wire must be 14 AWG or larger, regardless of locations and use. B. Wire must be copper stranded. C. The only wire that does not have to be in a suitable enclosure or cover is the ground wire used with portable tools and lights. D. All of the above.

Description : Wire in general, when used aboard vessels must meet minimum requirements. Which of the following statements is/are correct? A. Each wire must be 14 AWG or larger, regardless of locations and use. B. ... enclosure or cover is the ground wire used with portable tools and lights. D. All of the above.

Last Answer : Answer: B

The illustrated motor fails to start and gives a loud hum when the start button is depressed, your first action should be to __________. EL-0007 A. disassemble the motor to fix the centrifical switch so the start windings will be energized B. push the stop button to deenergize the 'M' coil C. reset the thermal overload D. hold the 'M' contactor closed by hand while wearing electrical safety gloves to get motor started

Description : The illustrated motor fails to start and gives a loud hum when the start button is depressed, your first action should be to __________. EL-0007 A. disassemble the motor to fix the centrifical ... D. hold the 'M' contactor closed by hand while wearing electrical safety gloves to get motor started

Last Answer : Answer: B

The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. continuity of service on main bus under short circuit conditions in a branch C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Description : The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. ... C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Last Answer : Answer: D

Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on different phases will not cause an outage. C. Ground detection systems are unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Description : Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on ... unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Last Answer : Answer: A

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

What safety precaution must be taken before replacing a transistor?

Description : What safety precaution must be taken before replacing a transistor?

Last Answer : The power must be removed from the circuit.

As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble pushbutton switches and drain water each week C. remove motor covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Description : As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble ... covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Last Answer : Answer: A

You have installed a Zener diode in parallel with a load. While measuring the voltage across the Zener diode it is found that it does not change as the current through the load increases. This means that the Zener diode __________. A. is working as it should B. is shorted C. is open D. does not regulate as it should

Description : You have installed a Zener diode in parallel with a load. While measuring the voltage across the Zener diode it is found that it does not change as the current through the load increases. This means that the ... is working as it should B. is shorted C. is open D. does not regulate as it should

Last Answer : Answer: A

There is a lamp inside a photography darkroom. When the darkroom door is closed, it is impossible to tell from outside the room whether or not the lamp is on. There are two switches outside the door of the darkroom. One or both of the switches may control the lamp. It also could be that neither of the switches control the lamp. All you know is that the light bulb is currently off and that the lamp and bulb are in working condition. The darkroom door is closed and once you open the door you cannot touch either of the switches. If you can only open the dark-room door one time, how can you tell which switches, if any, control the lamp? -Riddles

Description : There is a lamp inside a photography darkroom. When the darkroom door is closed, it is impossible to tell from outside the room whether or not the lamp is on. There are two switches outside the door of ... dark-room door one time, how can you tell which switches, if any, control the lamp? -Riddles

Last Answer : Turn the first switch on and leave it on for ten minutes. After ten minutes, turn that switch off and turn the second switch on. Open the darkroom door, and lightly (in case it is hot) touch the ... one controls the lamp. If the lamp is off, and the bulb is cool, neither switch controls the lamp.

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: D

Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of the auditor's report. b. Study and evaluate the system of internal administrative control. c. Tour the client's facilities and review the general records. d. Consult with and review the work of the predecessor auditor prior to discussing the engagement with the client management

Description : Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of ... and review the work of the predecessor auditor prior to discussing the engagement with the client management

Last Answer : Tour the client's facilities and review the general records

Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of the auditor's report. b. Study and evaluate the system of internal administrative control. c. Tour the client's facilities and review the general records. d. Consult with and review the work of the predecessor auditor prior to discussing the engagement with the client management

Description : Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of ... and review the work of the predecessor auditor prior to discussing the engagement with the client management

Last Answer : Tour the client's facilities and review the general records

Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of the auditor's report. b. Study and evaluate the system of internal administrative control. c. Tour the client's facilities and review the general records. d. Consult with and review the work of the predecessor auditor prior to discussing the engagement with the client management

Description : Which of the following is the most likely first step an auditor would perform at the beginning of an initial audit engagement? a. Prepare a rough draft of the financial statements and of ... and review the work of the predecessor auditor prior to discussing the engagement with the client management

Last Answer : Tour the client's facilities and review the general records

To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings C. send it ashore to an approved service facility D. rinse all electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Description : To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings ... electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Last Answer : Answer: A

Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test, because the ___________. A. static charge of the machine may give a false reading B. armature will have a greater number of leakage paths C. insulation may be damaged D. insulation may be covered with moisture

Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test, because the ___________. A. static charge of the machine ... number of leakage paths C. insulation may be damaged D. insulation may be covered with moisture

Last Answer : Answer: A

The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier

Last Answer : Answer: A