Two voltmeters have the same range 0-400V. The internal impedance ...

Two voltmeters have the same range 0-400V. The internal impedance are 30,000 Ohms and 20,000 Ohms. If they are connected in series and 600V be applied across them, the readings are
by

1 Answer

Answer :

Two voltmeters have the same range 0-400V. The internal impedance are 30,000 Ohms and 20,000 Ohms. If they are connected in series and 600V be applied across them, the readings are 360V and 240V.

by

Related questions

The moving iron voltmeters are likely:

Last Answer : The moving iron voltmeters are likely: To indicate lower value of ac than on dc.

An accurate voltmeter must have an internal impedance of

Description : An accurate voltmeter must have an internal impedance of (A) very low value. (B) very high value (C) medium value. (D) zero Value

Last Answer : An accurate voltmeter must have an internal impedance of very high value

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range

Description : An ammeter has a current change of 0-5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) ... series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

Last Answer : An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of 0.05 ohm in parallel with the meter

How to connect two heating coils to three 400V phases?

Description : Hello. I need to connect two heating coils to three 400V phases. Don't know how? Thank you

Last Answer : Need Answer

A 400V/100 V, 10 KVA two-winding transformer is reconnected as an auto-transformer across a suitable

Description : A 400V/100 V, 10 KVA two-winding transformer is reconnected as an auto-transformer across a suitable voltage source. The maximum rating of such an arrangement could be  A) 50 KVA B) 15 KVA C) 12.5 KVA D) 8.75 KVA

Last Answer : A 400V/100 V, 10 KVA two-winding transformer is reconnected as an auto-transformer across a suitable voltage source. The maximum rating of such an arrangement could be 50 KVA

52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Description : 52 A transformer has 1000 primary turns, connected to 250V ac supply. To get 400V secondary voltage the no of secondary turns should be A. 1600 B. 250 C. 400 D. 1250

Last Answer : A. 1600

If a 3-phase, 400V, 50Hz, 4 pole induction motor is running at a slip of 5% then the relative speed of rotor

Description : If a 3-phase, 400V, 50Hz, 4 pole induction motor is running at a slip of 5% then the relative speed of rotor field with respect to stator filed is:

Last Answer : If a 3-phase, 400V, 50Hz, 4 pole induction motor is running at a slip of 5% then the relative speed of rotor field with respect to stator filed is: zero

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Last Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

The power input to the rotor of a 400V, 50 Hz 6 pole three phase induction motor is 20kW. The slip is 3%...

Description : The power input to the rotor of a 400V, 50 Hz 6 pole three phase induction motor is 20kW. The slip is 3%. The frequency of rotor currents is: (A) 1 Hz (B) 1.5 Hz (C) 2 Hz (D) 1 2 Hz

Last Answer : C

What are the advantages of using two voltmeters in series?

Description : What are the advantages of using two voltmeters in series?

Last Answer : Increased input impedance, greater accuracy, and increased voltage range.

Why ammeters have to be arranged in class and voltmeters in parallel circuit ?

Description : Why ammeters have to be arranged in class and voltmeters in parallel circuit ?

Last Answer : Ammeter must be added to the class because it measures the flow. When added in parallel, the flow will be divided into two parts. As a result, the exact value of the flow cannot be ... because adding voltage will change the voltage difference. But in parallel the voltage difference does not change.

`A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Description : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Last Answer : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is ... )` D. `V_(A)ne V_(B)ne V_(C )`

`A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Description : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Last Answer : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is ... )gtV_(3)` D. `V_(1)gtV_(2)=V_(3)`

What are voltmeters used for?

Description : What are voltmeters used for?

Last Answer : A voltmeter measures the voltage between two points in an electrical current. Voltmeters are commonly used to test the remaining life in a battery.

Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Description : Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Last Answer : Answer: B

AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Description : AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Last Answer : Answer: C

Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Description : Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Last Answer : Answer: B

List the six safety precautions for the use of voltmeters.

Description : List the six safety precautions for the use of voltmeters.

Last Answer : a. Always connect a voltmeter in parallel. b. Always start with the highest range. c. Deenergize and discharge the circuit before connecting or disconnecting the voltmeter. d. ... to measure ac voltage. f. Observe the general safety precautions of electric and electronic devices.

Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Description : Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Last Answer : sinusoidal

All voltmeters except one of the following are operated by the passage of current

Description : All voltmeters except one of the following are operated by the passage of current

Last Answer : electrostatic

Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction...

Description : Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction is simplified due to

Last Answer : Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction is simplified due to Large electrostatic forces.

Electronic Voltmeters which use rectifiers employ negative feedback. This is done -

Description : Electronic Voltmeters which use rectifiers employ negative feedback. This is done -  a) To increase the overall gain b) To improve stability c) To overcome non -linearity of the diodes d) None of the above

Last Answer : Electronic Voltmeters which use rectifiers employ negative feedback. This is done - To overcome non -linearity of the diodes

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

Description : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Last Answer : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

It is desired to convert a 0-1000A meter movement, with an internal ...

Description : It is desired to convert a 0-1000A meter movement, with an internal resistance of 100 ohms, into a 0-100mA meter. The required value of shunt resistance is about 

Last Answer : It is desired to convert a 0-1000A meter movement, with an internal resistance of 100 ohms, into a 0-100mA meter. The required value of shunt resistance is about 1 ohms.

What is the range of the characteristic impedance of lines used in actual practice?

Description : What is the range of the characteristic impedance of lines used in actual practice?

Last Answer : Between 50 and 600 ohms.

Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Description : Which preamplifier design (high-impedance or transimpedance) provides improvements in bandwidth and greater dynamic range with some degradation in sensitivity from an increase in noise?

Last Answer : Transimpedance.

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

A single phase transformer rated at 3000 kVA, 69 kV 4.16 kV, 60 Hz has a total internal impedance Zp of 127...

Description : A single phase transformer rated at 3000 kVA, 69 kV 4.16 kV, 60 Hz has a total internal impedance Zp of 127 ohm, referred to the primary side. Calculate the primary current if the secondary is accidentally short circuited.  (A) 43.5 A (B) 543 A (C) 9006 A (D) 721 A 

Last Answer : 543A

The measurement range of an ammeter can be increased by using a:

Description : The measurement range of an ammeter can be increased by using a:

Last Answer : The measurement range of an ammeter can be increased by using a: low resistance in shunt

In order to increase the range of a voltmeter

Description : In order to increase the range of a voltmeter

Last Answer : In order to increase the range of a voltmeter a high resistance is connected in series

Range of a voltmeter can be extended by connecting a

Description : Range of a voltmeter can be extended by connecting a

Last Answer : Range of a voltmeter can be extended by connecting a Multiplier in series

A DVM has a 3 1/2 digit display. The 1 volt range can read upon

Description : A DVM has a 3 1/2 digit display. The 1 volt range can read upon

Last Answer : A DVM has a 3 1/2 digit display. The 1 volt range can read upon 1.999.

If the instrument is to have a wide range, the instrument should have

Last Answer : If the instrument is to have a wide range, the instrument should have Logarithmic scale.

An instrument transformer is used to extend the range of

Last Answer : An instrument transformer is used to extend the range of induction instrument.

The internal resistance of the ammeter should ideally be

Last Answer : The internal resistance of the ammeter should ideally be Zero.

The internal resistance of an ammeter should be

Last Answer : The internal resistance of an ammeter should be Very small.

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. ...

Description : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

Last Answer : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. 99.99 K ohms is the value of series resistor to be used.

The full-scale deflection current of an ammeter is 1 mA and its internal...

Description :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?

Last Answer :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, 1/49.99 ohms is the value of the shunt resistance to be used.

Two transformers having the same p.u. impedance connected in parallel share the connected load

Description : Two transformers having the same p.u. impedance connected in parallel share the connected load (A) equally (B) in proportion to the respective ratings (C) in proportion to the voltage ratio (D) in proportion to the zero phase displacement

Last Answer : Two transformers having the same p.u. impedance connected in parallel share the connected load in proportion to the respective ratings

When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Description : When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Last Answer : Ans: D

Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Description : Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Last Answer : Answer: D

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit.

Description : Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit. 

Last Answer : Draw a circuit diagram of R.C. series circuit. Draw impedance triangle and power triangle for same circuit. 

What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Description : What is the characteristic impedance of a two-wire line with the following data: diameter = 0.023in., spacing =0.5 in., insulation = PE.? A. 300Ω B. 250Ω C. 305Ω D. 301Ω

Last Answer : D. 301Ω

An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Description : An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms? A. 0.01 amperes B. 0.60 amperes C. 1.67 amperes D. 100 amperes

Last Answer : Answer: B

The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Description : The power supplied to a motor is six kilowatts at 120 volts. What is the impedance of the motor? A. 0.05 Ohms B. 0.50 Ohms C. 2.40 Ohms D. 24.00 Ohms

Last Answer : Answer: C

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4