Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction...

Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction is simplified due to
by

1 Answer

Answer :

Electrostatic voltmeters are particularly suitable for measuring high voltages because the construction is simplified due to Large electrostatic forces.

by

Related questions

Electrostatic type instruments are mainly used for measurement of: a) Heavy currents b) Low currents c) Low voltages d) High voltages

Description : Electrostatic type instruments are mainly used for measurement of: a) Heavy currents b) Low currents c) Low voltages d) High voltages

Last Answer : Ans: D

Hastelloy C is a good material of construction in chemical process industry, since it is (A) Highly corrosion resistant and is readily fabricated (B) Relatively inexpensive although it can be fabricated with some difficulty (C) Corrosion resistant to most alkalis, particularly because of its copper content (D) Light and resists attack by acids

Description : Hastelloy C is a good material of construction in chemical process industry, since it is (A) Highly corrosion resistant and is readily fabricated (B) Relatively inexpensive although it can be ... most alkalis, particularly because of its copper content (D) Light and resists attack by acids

Last Answer : (D) Light and resists attack by acids

Select the general anaesthetic that is particularly suitable for outpatient surgery because of quick recovery and short-lived post-anaesthetic psychomotor impairment: A. Ether B. Halothane C. Enflurane D. Desflurane

Description : Select the general anaesthetic that is particularly suitable for outpatient surgery because of quick recovery and short-lived post-anaesthetic psychomotor impairment: A. Ether B. Halothane C. Enflurane D. Desflurane

Last Answer : D. Desflurane

Resistance measuring instrument particularly used in determining the insulation resistance

Description : Resistance measuring instrument particularly used in determining the insulation resistance

Last Answer : Megger/Megaohmmeter

. The most suitable equipment for removing the fine dust particle (< 1 micron dia.) from air below its dew point will be a/an (A) Bag filter (B) Electrostatic precipitator (C) Cyclone separator (D) Wet scrubber

Description : . The most suitable equipment for removing the fine dust particle (< 1 micron dia.) from air below its dew point will be a/an (A) Bag filter (B) Electrostatic precipitator (C) Cyclone separator (D) Wet scrubber

Last Answer : (B) Electrostatic precipitator

Most efficient and suitable dust removal equipment for removal of fly￾ash from flue gas in a thermal power plant is the (A) Gravity settling chamber (B) Cyclone separator (C) Electrostatic precipitator (D) Bag filter

Description : Most efficient and suitable dust removal equipment for removal of fly￾ash from flue gas in a thermal power plant is the (A) Gravity settling chamber (B) Cyclone separator (C) Electrostatic precipitator (D) Bag filter

Last Answer : (C) Electrostatic precipitator

Is the climate of the country particularly suitable for cultivation ?

Last Answer : The climate of the country is especially suitable for jute cultivation.

Why ammeters have to be arranged in class and voltmeters in parallel circuit ?

Description : Why ammeters have to be arranged in class and voltmeters in parallel circuit ?

Last Answer : Ammeter must be added to the class because it measures the flow. When added in parallel, the flow will be divided into two parts. As a result, the exact value of the flow cannot be ... because adding voltage will change the voltage difference. But in parallel the voltage difference does not change.

`A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Description : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Last Answer : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is ... )` D. `V_(A)ne V_(B)ne V_(C )`

`A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Description : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is applied between `x` and `y` the voltme

Last Answer : `A, B` and `C` are voltmeters of resistances `R, 1.5R` and `3R` respectively. When some potential difference is ... )gtV_(3)` D. `V_(1)gtV_(2)=V_(3)`

What are voltmeters used for?

Description : What are voltmeters used for?

Last Answer : A voltmeter measures the voltage between two points in an electrical current. Voltmeters are commonly used to test the remaining life in a battery.

Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Description : Most AC voltmeters are calibrated to indicate __________. A. peak-to-peak voltage B. root-mean-square voltage C. average voltage D. peak voltage only

Last Answer : Answer: B

AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Description : AC voltmeters are generally calibrated to read the ________. A. instantaneous voltage B. average voltage C. RMS voltage D. peak voltage

Last Answer : Answer: C

Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Description : Ammeters and voltmeters used in sinusoidal AC power systems indicate which of the following values of the waveforms measured? A. Peak value B. Root-mean-square value C. Average value D. Maximum value

Last Answer : Answer: B

List the six safety precautions for the use of voltmeters.

Description : List the six safety precautions for the use of voltmeters.

Last Answer : a. Always connect a voltmeter in parallel. b. Always start with the highest range. c. Deenergize and discharge the circuit before connecting or disconnecting the voltmeter. d. ... to measure ac voltage. f. Observe the general safety precautions of electric and electronic devices.

What are the advantages of using two voltmeters in series?

Description : What are the advantages of using two voltmeters in series?

Last Answer : Increased input impedance, greater accuracy, and increased voltage range.

Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Description : Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Last Answer : sinusoidal

All voltmeters except one of the following are operated by the passage of current

Description : All voltmeters except one of the following are operated by the passage of current

Last Answer : electrostatic

Electronic Voltmeters which use rectifiers employ negative feedback. This is done -

Description : Electronic Voltmeters which use rectifiers employ negative feedback. This is done -  a) To increase the overall gain b) To improve stability c) To overcome non -linearity of the diodes d) None of the above

Last Answer : Electronic Voltmeters which use rectifiers employ negative feedback. This is done - To overcome non -linearity of the diodes

Two voltmeters have the same range 0-400V. The internal impedance ...

Description : Two voltmeters have the same range 0-400V. The internal impedance are 30,000 Ohms and 20,000 Ohms. If they are connected in series and 600V be applied across them, the readings are

Last Answer : Two voltmeters have the same range 0-400V. The internal impedance are 30,000 Ohms and 20,000 Ohms. If they are connected in series and 600V be applied across them, the readings are 360V and 240V.

The moving iron voltmeters are likely:

Last Answer : The moving iron voltmeters are likely: To indicate lower value of ac than on dc.

At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to produce higher voltages and do not have to be charged as often C. can be charged and discharged many times without much damage D. have no individual cells to replace at the end of useful life

Description : At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to ... times without much damage D. have no individual cells to replace at the end of useful life

Last Answer : Answer: C

Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need fewer cells in connected series and less mounting space C. have higher output voltages and require no maintenance D. all of the above

Description : Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they _______________. A. deliver a large amount of power and can be recharged in a shorter time B. need ... less mounting space C. have higher output voltages and require no maintenance D. all of the above

Last Answer : Answer: A

Thermocouple is suitable for measuring (A) Liquid temperatures only (B) Very high temperatures only (C) Very low temperatures only (D) Both high and low temperatures

Description : Thermocouple is suitable for measuring (A) Liquid temperatures only (B) Very high temperatures only (C) Very low temperatures only (D) Both high and low temperatures

Last Answer : (D) Both high and low temperatures

Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Description : Nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. put out higher voltages and require no maintenance B. can remain idle and keep a full charge for a long time C. need fewer cells in series and use less mounting space D. all of the above

Last Answer : Answer: B

Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Description : Ungrounded neutral transmission system is not recommended because of system (a) insulation being overstressed due to over voltages (b) insulation overstress may lead to failure and subsequent phase to phase faults (c) being inadequately protected against ground fault (d) all of the above

Last Answer : (d) all of the above

Alternating voltages and currents are represented by straight line with an arrow to represent the

Description : Alternating voltages and currents are represented by straight line with an arrow to represent the magnitude and direction. This representation is called

Last Answer : Alternating voltages and currents are represented by straight line with an arrow to represent the magnitude and direction. This representation is called Phasor quantity

A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :

Description : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are :  (A) less than 66 kV (B) lie between 66 kV and 110 kV (C) more than 165 kV (D) lie between 110 kV and 165 kV

Last Answer : A minimum clearance of 6.3 m to ground is required for overhead lines when operating voltages are : lie between 66 kV and 110 kV

In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line...

Description : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: A. 2,000 V B. 6,000 V C. 666 V D. 3,464 V

Last Answer : In a certain three -wire Y -connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages will be: 3,464 V

Polyphase generators produce simultaneous multiple sinusoidal voltages that are separated by certain...

Description : Polyphase generators produce simultaneous multiple sinusoidal voltages that are separated by certain constant: A. Phase -angles B. Frequency C. Voltage D. Current

Last Answer : Polyphase generators produce simultaneous multiple sinusoidal voltages that are separated by certain constant: Phase -angles

Specify the material of construction suitable for handling concentrated HNO3 at 100°C. (A) High silicon iron, Kel-F and Teflon (B) Tin and wood (C) Silicone rubber (D) Stainless steel

Description : Specify the material of construction suitable for handling concentrated HNO3 at 100°C. (A) High silicon iron, Kel-F and Teflon (B) Tin and wood (C) Silicone rubber (D) Stainless steel

Last Answer : (A) High silicon iron, Kel-F and Teflon

Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability to be cast, rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Description : Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability ... rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Last Answer : (A) High strength to weight ratio

most suitable material of construction for a sewer to carry sewage under high pressure is (A) Asbestos cement (B) Steel (C) Cement concrete (D) Stoneware

Description : most suitable material of construction for a sewer to carry sewage under high pressure is (A) Asbestos cement (B) Steel (C) Cement concrete (D) Stoneware

Last Answer : Option B

Sodium valproate should be used with caution in young children because they are particularly at risk of developing the following adverse effect: A. Hepatitis B. Loss of hair C. Anorexia D. Tremor

Description : Sodium valproate should be used with caution in young children because they are particularly at risk of developing the following adverse effect: A. Hepatitis B. Loss of hair C. Anorexia D. Tremor

Last Answer : A. Hepatitis

Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range until a suitable reading is obtained. C. The indicating needle is deflected from left to right regardless of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Description : Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range ... of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Last Answer : Answer: A

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

The most suitable flow measuring device for the fluid flow measurement in a very large diameter pipeline is a (A) Weir(B) Pitot tube(C) Kennison nozzle(D) V-notch

Description : The most suitable flow measuring device for the fluid flow measurement in a very large diameter pipeline is a (A) Weir (B) Pitot tube (C) Kennison nozzle (D) V-notch

Last Answer : (B) Pitot tube

The most serious disadvantage of an orificemeter is that (A) It is not very accurate (B) It is very costly (C) Most of the pressure drop is not recoverable (D) It is not suitable for measuring gas flow

Description : The most serious disadvantage of an orificemeter is that (A) It is not very accurate (B) It is very costly (C) Most of the pressure drop is not recoverable (D) It is not suitable for measuring gas flow

Last Answer : (C) Most of the pressure drop is not recoverable

Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations? (A) Measuring angle and distance from one transit station (B) Measuring angles to the point from at least two stations (C) Measuring angle at one station and distance from other (D) Measuring distance from two points on traverse line

Description : Which of the following methods of theodolite traversing is suitable for locating the details which are far away from transit stations? (A) Measuring angle and distance from one transit station (B) ... at one station and distance from other (D) Measuring distance from two points on traverse line

Last Answer : (B) Measuring angles to the point from at least two stations

Which one of the following frequency meter is suitable for measuring radio frequency?

Description : Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

Last Answer : Which one of the following frequency meter is suitable for measuring radio frequency?   (a) Vibrating reed frequency meter (b) Weston frequency meter (c) Electrical resonance frequency meter (d) Heterodyne frequency meter 

Energy stored in electrostatic field of capacitance formula

Description : Energy stored in electrostatic field of capacitance formula

Last Answer : Energy stored in electrostatic field of capacitance formula

Which of the following statements is not valid in case of conductors in electrostatic fields?

Description : Which of the following statements is not valid in case of conductors in electrostatic fields? A) The static electric field intensity inside a conductor is zero B) The static electric field intensity at ... the surface C) The conductor surface is an equivalent potential surface D) None of the above

Last Answer : Which of the following statements is not valid in case of conductors in electrostatic fields? A) The static electric field intensity inside a conductor is zero B) The static electric field intensity at ... the surface C) The conductor surface is an equivalent potential surface D) None of the above

Consider the following statements associated with the basic electrostatic properties of ideal conductors :

Description : Consider the following statements associated with the basic electrostatic properties of ideal conductors :  1. The resultant field inside is zero. 2. The net charge density in the interior is zero. 3. Any net charges reside on the ... (b) 3, 4 and 5 only (c) 1, 2 and 3 only (d) 2 and 3 only

Last Answer : Consider the following statements associated with the basic electrostatic properties of ideal conductors : 1. The resultant field inside is zero. 2. The net charge density in the interior is zero. 3. Any net charges reside on the ... (b) 3, 4 and 5 only (c) 1, 2 and 3 only (d) 2 and 3 only

Voltage applied across a ceramic dielectric produces an electrostatic...

Description : Voltage applied across a ceramic dielectric produces an electrostatic field 100 times greater than in air. The dielectric constant? of the ceramic equals________. 

Last Answer : Voltage applied across a ceramic dielectric produces an electrostatic field 100 times greater than in air. The dielectric constant? of the ceramic equals 100.

The primary function of an electric motor is to ___________. A. develop torque B. generate high voltages C. produce a magnetic field D. generate high electrical resistance

Description : The primary function of an electric motor is to ___________. A. develop torque B. generate high voltages C. produce a magnetic field D. generate high electrical resistance

Last Answer : Answer: A

High voltages lead to A. less power loss B. more power loss C. high current D. high resistance

Description :   High voltages lead to A. less power loss B. more power loss C. high current D. high resistance

Last Answer : less power loss

In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Description : In a series-RLC circuit, what is the condition of the circuit if there is high impedance, low current, and low reactance voltages

Last Answer : Nonresonant (circuit is either above or below resonance)