In ______ machines, the size of the shaft is decided by the critical speed which depends on the deflection of the shaft. (a) small (b) medium (c) large (d) any of the above.

In ______ machines, the size of the shaft is decided by the critical speed which depends
on the deflection of the shaft.
(a) small
(b) medium
(c) large
(d) any of the above.
by

1 Answer

Answer :

(c) large
by

Related questions

Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.

Description : Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.

Last Answer : (d) 2000 to 2500 r.p.m.

Electrical machines having power outputs ranging from a few kW upto approximately 250 kW may be classified as (a) small size machines (b) medium size machines (c) large size machines (d) any ofthe above

Description : Electrical machines having power outputs ranging from a few kW upto approximately 250 kW may be classified as (a) small size machines (b) medium size machines (c) large size machines (d) any ofthe above

Last Answer : (b) medium size machines

Electrical machines having a power output upto about 750 W may be called_______machines. (a) small size (b) medium size (c) large size (d) any of the above

Description : Electrical machines having a power output upto about 750 W may be called_______machines. (a) small size (b) medium size (c) large size (d) any of the above

Last Answer : (a) small size

Aluminium when adopted as a conductor material in ______ transformers, decreases the overall cost of the transformer (a) small size (b) medium size (c) large size (d) any of the above size

Description : Aluminium when adopted as a conductor material in ______ transformers, decreases the overall cost of the transformer (a) small size (b) medium size (c) large size (d) any of the above size

Last Answer : (a) small size

The design of mechanical parts is particularly important in case of _____ speed machines. (a) low (b) medium (c) high (d) any of the above

Description : The design of mechanical parts is particularly important in case of _____ speed machines. (a) low (b) medium (c) high (d) any of the above

Last Answer : (c) high

Dummy coil should not be used in (a) small machines (b) large machines (c) either (a) or (b) (d) none of the above

Description : Dummy coil should not be used in (a) small machines (b) large machines (c) either (a) or (b) (d) none of the above

Last Answer : (b) large machines

Yokes with rectangular cross-section are used for (a) small capacity transformers (b) medium capacity transformers (c) large capacity transformers (d) any of the above

Description : Yokes with rectangular cross-section are used for (a) small capacity transformers (b) medium capacity transformers (c) large capacity transformers (d) any of the above

Last Answer : (a) small capacity transformers

In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Description : In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Last Answer : (c) large in comparison with the arma-ture mmf

D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Description : D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Last Answer : (c) better ventilation

The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Description : The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Last Answer : (b) hydrogen

In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810

Last Answer : C 705

In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Last Answer : (c) between 9 to 16

In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Last Answer : (d) between 25 to 35 mm

In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Last Answer : (d) 10 mm

Machines cooled by direct cooling method may be called (a) "supercharged" (b) "inner cooled" (c) "conductor cooled" (d) any of the above

Description : Machines cooled by direct cooling method may be called (a) "supercharged" (b) "inner cooled" (c) "conductor cooled" (d) any of the above

Last Answer : (d) any of the above

Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto (a) 10 MW (b) 30 MW (c) 60 MW (d) 150 MW

Description : Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto (a) 10 MW (b) 30 MW (c) 60 MW (d) 150 MW

Last Answer : (c) 60 MW

is universally used for windings of electrical machines because it is easily workable without any possibility of fracture. (a) Silver (b) Steel (c) Aluminium (d) Copper

Description : is universally used for windings of electrical machines because it is easily workable without any possibility of fracture. (a) Silver (b) Steel (c) Aluminium (d) Copper

Last Answer : (d) Copper

The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Description : The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Last Answer : (d) All of the above

The value of exciting or magnetizing current depends upon which of the following factors ? (a) Total m.m.f. required (b) The number of turns in the exciting winding (c) The way in which the winding is distributed (d) All of the above

Description : The value of exciting or magnetizing current depends upon which of the following factors ? (a) Total m.m.f. required (b) The number of turns in the exciting winding (c) The way in which the winding is distributed (d) All of the above

Last Answer : (d) All of the above

On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Description : On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Last Answer : (e) All ofthe above

The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Description : The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Last Answer : (c) radiation

The surge phenomenon is particularly important in case of (a) low voltage transformers (b) medium voltage transformers (c) high voltage transformers (d) any of the above

Description : The surge phenomenon is particularly important in case of (a) low voltage transformers (b) medium voltage transformers (c) high voltage transformers (d) any of the above

Last Answer : (c) high voltage transformers

Disc windings are primarily used in (a) short capacity transformers (b) medium capacity transformers (c) high capacity transformers (d) any of the above

Description : Disc windings are primarily used in (a) short capacity transformers (b) medium capacity transformers (c) high capacity transformers (d) any of the above

Last Answer : (c) high capacity transformers

cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Description : cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Last Answer : (a) Direct

The cold rolled grain oriented steel has ______ permeability in the direction of the grain orientation. (a) minimum (b) maximum (c) nil (d) none of the above

Description : The cold rolled grain oriented steel has ______ permeability in the direction of the grain orientation. (a) minimum (b) maximum (c) nil (d) none of the above

Last Answer : (b) maximum

In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Description : In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Last Answer : (a) 2 to 3 times greater

The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Description : The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Last Answer : (d) 7

Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Description : Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Last Answer : (b) low

Materials exhibiting zero value of resistivity are known as ______ . (a) conductors (b) semiconductors (c) insulators (d) superconductors

Description : Materials exhibiting zero value of resistivity are known as ______ . (a) conductors (b) semiconductors (c) insulators (d) superconductors

Last Answer : (d) superconductors

The length cf air gap to be provided in ______ is primarily determined by power factor consideration. (a) d.c. series motor . (b) d.c. shunt motor (c) induction motor (d) synchronous motor

Description : The length cf air gap to be provided in ______ is primarily determined by power factor consideration. (a) d.c. series motor . (b) d.c. shunt motor (c) induction motor (d) synchronous motor

Last Answer : (c) induction motor

The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above

Description : The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above

Last Answer : (a) high

The speed at which the shaft runs so that the additional deflection of the shaft from the axis of rotation becomes ___________, is known as critical or whirling speed. (A) zero (B) minimum (C) maximum (D) infinite

Description : The speed at which the shaft runs so that the additional deflection of the shaft from the axis of rotation becomes ___________, is known as critical or whirling speed. (A) zero (B) minimum (C) maximum (D) infinite

Last Answer : (D) infinite

If the static deflection is 1.665×10 -3 m, calculate the critical speed of the shaft in rps. Centre of disc at 0.25m away from centre of axis of shaft. A. 8.64 B. 9.64 C. 10.64 D. 12.2

Description : If the static deflection is 1.665×10 -3 m, calculate the critical speed of the shaft in rps. Centre of disc at 0.25m away from centre of axis of shaft. A. 8.64 B. 9.64 C. 10.64 D. 12.2

Last Answer : D. 12.2

The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Last Answer : (a) quiet

A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Last Answer : (d) 5.4 to 6.2 A/mm2

For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Description : For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Last Answer : (c) 2.2 to 3.2 A/mm2

Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Description : Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Last Answer : (d) Cast-iron

Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above

Description : Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above

Last Answer : (e) All ofthe above

In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s

Description : In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s

Last Answer : (c) 30 m/s

The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Description : The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Last Answer : (d) All of the above types

In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Description : In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Last Answer : (b) high power factor

The critical speed of a shaft depends upon its A. Mass B. Stiffness C. Mass and stiffnessD. Stiffness and eccentricity

Description : The critical speed of a shaft depends upon its A. Mass B. Stiffness C. Mass and stiffnessD. Stiffness and eccentricity

Last Answer : C. Mass and stiffness

The Critical Speed Of Rotating Shaft Depends Upon What?

Description : The Critical Speed Of Rotating Shaft Depends Upon What?

Last Answer : Mass and stiffness.

Critical speed is expressed as ______. A) rotation of the shaft in degrees (B) rotation of the shaft in radians (C) rotation of the shaft in minutes (D) the natural frequency of the shaf

Description : Critical speed is expressed as ______. A) rotation of the shaft in degrees (B) rotation of the shaft in radians (C) rotation of the shaft in minutes (D) the natural frequency of the shaf

Last Answer : (D) the natural frequency of the shaft

Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Description : Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Last Answer : (e) All of the above

In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Last Answer : (d) 400 A

In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above

Description : In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above

Last Answer : (b) equal to

The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Description : Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Last Answer : (e) All of the above