Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above

Which ofthe following is an advantage of hydrogen cooling ?
(a) Increase in efficiency
(b) Increase in ratings
(c) Increase in life
(d) Smaller size of coolers
(e) All ofthe above
by

1 Answer

Answer :

(e) All ofthe above
by

Related questions

With conventional hydrogen cooling it is possible to increase the rating of a single unit to (a) 50 MW (b) 100 MW (c) 200 MW (d) none ofthe above

Description : With conventional hydrogen cooling it is possible to increase the rating of a single unit to (a) 50 MW (b) 100 MW (c) 200 MW (d) none ofthe above

Last Answer : (c) 200 MW

cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Description : cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above

Last Answer : (a) Direct

Which ofthe following methods is used for air cooling of turbo-alternators ? (a) One sided axial ventilation (b) Two sided axial ventilation (c) Multiple inlet system (d) All ofthe above

Description : Which ofthe following methods is used for air cooling of turbo-alternators ? (a) One sided axial ventilation (b) Two sided axial ventilation (c) Multiple inlet system (d) All ofthe above

Last Answer : (d) All ofthe above

In direct cooled system using hydrogen both stator and rotor conductors are made (a) solid (b) hollow (c) perforated (d) any ofthe above

Description : In direct cooled system using hydrogen both stator and rotor conductors are made (a) solid (b) hollow (c) perforated (d) any ofthe above

Last Answer : (b) hollow

With direct water cooling it is possible to have ratings of about (a) 200 MW (b) 300 MW (c) 400 MW (d) 600 MW

Description : With direct water cooling it is possible to have ratings of about (a) 200 MW (b) 300 MW (c) 400 MW (d) 600 MW

Last Answer : (d) 600 MW

The mcrease in heat dissipation by air blasts is due to increase in (a) conduction (b) convection (e) radiation (d) any ofthe above

Description : The mcrease in heat dissipation by air blasts is due to increase in (a) conduction (b) convection (e) radiation (d) any ofthe above

Last Answer : (b) convection

Electrical machines having power outputs ranging from a few kW upto approximately 250 kW may be classified as (a) small size machines (b) medium size machines (c) large size machines (d) any ofthe above

Description : Electrical machines having power outputs ranging from a few kW upto approximately 250 kW may be classified as (a) small size machines (b) medium size machines (c) large size machines (d) any ofthe above

Last Answer : (b) medium size machines

On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Description : On which of the following variables heat convected depends ? (a) Power density (b) Temperature difference between heated surface and coolant (c) Thermal resistivity, density, specific heat (d) Gravitational constant (e) All ofthe above

Last Answer : (e) All ofthe above

The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with respect to flux and the flux varies in magnitude with respect to time (c) Both the changes mentioned above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Description : The change in flux linkages can be caused in which ofthe following ways ? (a) The flux is constant with respect to time and is stationary and the coil moves through it (b) The coil is stationary with ... above occure together, i.e., the coil moves through a time varying field (d) All ofthe above

Last Answer : (d) All ofthe above

The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Description : The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Last Answer : (c) radiation

The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ? (a) Conduction (b) Convection (c) Radiation (d) All ofthe above

Description : The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ? (a) Conduction (b) Convection (c) Radiation (d) All ofthe above

Last Answer : (d) All ofthe above

Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Description : Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Last Answer : (b) low

Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Description : Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Last Answer : (d) Cast-iron

The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Description : The action of electromagnetic machines can be related to which ofthe following basic principles ? (a) Induction (b) Interaction (c) Alignment (d) All of the above

Last Answer : (d) All of the above

The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Description : The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Last Answer : (b) hydrogen

The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above

Description : The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above

Last Answer : (e) All of the above

A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Last Answer : (d) 5.4 to 6.2 A/mm2

Transformers with a capacity of upto _____ have a cooling radiator system with natural cooling (a) 2 MVA (b) 5 MVA (c) 7.5 MVA (d) 10 MVA

Description : Transformers with a capacity of upto _____ have a cooling radiator system with natural cooling (a) 2 MVA (b) 5 MVA (c) 7.5 MVA (d) 10 MVA

Last Answer : (d) 10 MVA

In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Description : In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above

Last Answer : (a) 2 to 3 times greater

The time taken by the machine to attain 0.632 of its final steady temperature rise is called (a) heating time constant (b) cooling time constant (c) either (a) or (b) (d) none of the above

Description : The time taken by the machine to attain 0.632 of its final steady temperature rise is called (a) heating time constant (b) cooling time constant (c) either (a) or (b) (d) none of the above

Last Answer : (a) heating time constant

Direct water cooling of rotor winding presents (a) no mechanical difficulties (b) lesser mechanical difficulties (c) greater mechanical difficulties (d) none of the above

Description : Direct water cooling of rotor winding presents (a) no mechanical difficulties (b) lesser mechanical difficulties (c) greater mechanical difficulties (d) none of the above

Last Answer : (c) greater mechanical difficulties

Machines cooled by direct cooling method may be called (a) "supercharged" (b) "inner cooled" (c) "conductor cooled" (d) any of the above

Description : Machines cooled by direct cooling method may be called (a) "supercharged" (b) "inner cooled" (c) "conductor cooled" (d) any of the above

Last Answer : (d) any of the above

Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto (a) 10 MW (b) 30 MW (c) 60 MW (d) 150 MW

Description : Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto (a) 10 MW (b) 30 MW (c) 60 MW (d) 150 MW

Last Answer : (c) 60 MW

impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Description : impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Last Answer : (e) All above

In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

Power transformers should be designed to have maximum efficiency (a) at one-fourth load (b) at one-half load (c) at or near full load (d) any of the above

Description : Power transformers should be designed to have maximum efficiency (a) at one-fourth load (b) at one-half load (c) at or near full load (d) any of the above

Last Answer : (c) at or near full load

The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above

Description : The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above

Last Answer : (a) high

The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Description : The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Last Answer : (d) 7

Hydrogen has a heat transfer co-efficient _____ times that of air (a) 1.5 (b) 2.5 (c) 3.5 (d) 4.5

Description : Hydrogen has a heat transfer co-efficient _____ times that of air (a) 1.5 (b) 2.5 (c) 3.5 (d) 4.5

Last Answer : (a) 1.5

The density of hydrogen is _____ times the density of air. (a) 0.07 (b) 1.5 (c) 2.5 (d) 3.5

Description : The density of hydrogen is _____ times the density of air. (a) 0.07 (b) 1.5 (c) 2.5 (d) 3.5

Last Answer : (a) 0.07

Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Description : Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Last Answer : (e) All of the above

Aluminium when adopted as a conductor material in ______ transformers, decreases the overall cost of the transformer (a) small size (b) medium size (c) large size (d) any of the above size

Description : Aluminium when adopted as a conductor material in ______ transformers, decreases the overall cost of the transformer (a) small size (b) medium size (c) large size (d) any of the above size

Last Answer : (a) small size

Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.

Description : Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.

Last Answer : (d) 2000 to 2500 r.p.m.

Electrical machines having a power output upto about 750 W may be called_______machines. (a) small size (b) medium size (c) large size (d) any of the above

Description : Electrical machines having a power output upto about 750 W may be called_______machines. (a) small size (b) medium size (c) large size (d) any of the above

Last Answer : (a) small size

In ______ machines, the size of the shaft is decided by the critical speed which depends on the deflection of the shaft. (a) small (b) medium (c) large (d) any of the above.

Description : In ______ machines, the size of the shaft is decided by the critical speed which depends on the deflection of the shaft. (a) small (b) medium (c) large (d) any of the above.

Last Answer : (c) large

The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Description : The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above

Last Answer : (a) increase

If an insulating material is operated beyond the maximum allowable temperature, its life is (a) drastically increased (b) drastically reduced (c) unaffected (d) none of the above

Description : If an insulating material is operated beyond the maximum allowable temperature, its life is (a) drastically increased (b) drastically reduced (c) unaffected (d) none of the above

Last Answer : (b) drastically reduced

In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Last Answer : (d) 400 A

Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Description : Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Last Answer : (e) All of the above

Which of the following in an application of D.C. motors? (a) Traction (b) Drives for process industry (c) Battery driven vehicles (d) Automatic control (e) All of the above

Description : Which of the following in an application of D.C. motors? (a) Traction (b) Drives for process industry (c) Battery driven vehicles (d) Automatic control (e) All of the above

Last Answer : (e) All of the above

For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above

Description : For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above

Last Answer : (d) 1.6 Wb/m2

In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Last Answer : (c) 15 percent

The design of electromagnets is based upon which of the following fundamental equations ? (a) Force equation (b) Magnetic circuit equation (c) Heating equation (d) Voltage equation (e) All of the above

Description : The design of electromagnets is based upon which of the following fundamental equations ? (a) Force equation (b) Magnetic circuit equation (c) Heating equation (d) Voltage equation (e) All of the above

Last Answer : (e) All of the above

By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Last Answer : (e) All of the above.

In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30

Last Answer : (c) between 9 to 16

In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Last Answer : (d) between 25 to 35 mm

The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Last Answer : (a) quiet

In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Description : In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above

Last Answer : (c) large in comparison with the arma-ture mmf

D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Description : D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Last Answer : (c) better ventilation

In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm

Last Answer : (d) 10 mm