Description : With direct water cooling it is possible to have ratings of about (a) 200 MW (b) 300 MW (c) 400 MW (d) 600 MW
Last Answer : (d) 600 MW
Description : In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above
Last Answer : (b) equal to
Description : Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.
Last Answer : (d) 2000 to 2500 r.p.m.
Description : Power transformers have rating (a) equal to 50 kVA (6) equal to 100 kVA (c) above 200 kVA (d) none of the above
Last Answer : (c) above 200 kVA
Description : is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron
Last Answer : (d) Cast-iron
Description : With conventional hydrogen cooling it is possible to increase the rating of a single unit to (a) 50 MW (b) 100 MW (c) 200 MW (d) none ofthe above
Last Answer : (c) 200 MW
Description : The stator of a D.C. machine comprises of (a) main poles (6) interpoles (c) frame (d) all of the above
Last Answer : (d) all of the above
Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30
Last Answer : (c) between 9 to 16
Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2
Last Answer : (d) 5.4 to 6.2 A/mm2
Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above
Last Answer : (a) quiet
Description : In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s
Last Answer : (c) 30 m/s
Description : The laminations of the armature of a D.C. machine are usually _____ thick. (a) 0.1 to 0.2 mm (b) 0.2 to 0.3 mm (c) 0.3 to 0.4 mm (d) 0.4 to 0.5 mm
Last Answer : (d) 0.4 to 0.5 mm
Description : The time taken by the machine to attain 0.632 of its final steady temperature rise is called (a) heating time constant (b) cooling time constant (c) either (a) or (b) (d) none of the above
Last Answer : (a) heating time constant
Description : The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above
Last Answer : (b) hydrogen
Description : The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ? (a) Conduction (b) Convection (c) Radiation (d) All ofthe above
Last Answer : (d) All ofthe above
Description : The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above
Last Answer : (a) high
Description : The resistivity of water should not be less than (a) 10 Q m (b) 100 Q m (c) 1000 Q m (d) 2000 Q m
Last Answer : (d) 2000 Q m
Description : Find the current density of a material with resistivity 20 units and electric field intensity 2000 units. a) 400 b) 300 c) 200 d) 100
Last Answer : d) 100
Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.
Last Answer : (e) All of the above.
Description : For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above
Last Answer : (d) 1.6 Wb/m2
Description : Which of the following brushes can be used for high values of current density ? (a) Metal graphite brushes (b) Hard carbon brushes (c) Electro-graphitic brushes (d) Natural graphite brushes
Last Answer : (a) Metal graphite brushes
Description : The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A
Last Answer : (d) upto 80 A
Description : For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2
Last Answer : (c) 2.2 to 3.2 A/mm2
Description : The value of exciting or magnetizing current depends upon which of the following factors ? (a) Total m.m.f. required (b) The number of turns in the exciting winding (c) The way in which the winding is distributed (d) All of the above
Last Answer : (d) All of the above
Description : The slot leakage can be calculated by making which of the following assumptions ? (a) The current in the slot conductors is uniformly distributed over their cross-section (b) The leakage path is straight ... is only considered. The reluctance of iron paths is assumed as zero (d) All of the above
Description : Which of the following methods is most accurate ? (a) Equivalent current method (b) Equivalent power method (c) Equivalent torque method (d) Method of average losses
Last Answer : (a) Equivalent current method
Description : Which of the following methods does not take into account the maximum temperature rise under variable load conditions ? (a) Equivalent power method (b) Equivalent current method (c) Method of average losses (d) Equivalent torque method
Last Answer : (c) Method of average losses
Description : Avalanche photodiode receivers candetect hits of transmitted databy receiving A. 100 photons B. 200 photons C. 300 photons D. 400 photons E. None of the above
Last Answer : 200 photons
Description : The daily water loss through gastrointestinal tract in an adult is about (A) Less than 100 ml/day (B) 200 ml/day (C) 300 ml/day (D) 400 ml/day
Last Answer : Answer : A
Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm
Last Answer : (d) 10 mm
Description : D.C. servomotors are used in (a) purely D.C. control systems (6) purely AC. control systems (c) both D.C. and AC. control systems (d) none of the above
Last Answer : (a) purely D.C. control systems
Description : A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm
Last Answer : (d) 5 + 0.9 kV mm
Description : By which of the following methods the temperature rise of windings and other parts may be determined ? (a) Thermometer method (6) Resistance method (c) Embedded temperature detector method (d) Any of the above
Last Answer : (d) Any of the above
Description : The cheapest modems cantransmit A. 300 bits per second B. 1,200 bitsper second C. 2,400 bits per second D. 4,800 bits per second E. None of the above
Last Answer : 300 bits per second
Description : Anil played 8 cricket matches. The mean (average) of the runs was found to be 80. After playing four more matches, the mean of the runs of all the matches was found to be 70. The total runs made in the last four matches is (A) 400 (B) 300 (C) 200 (D) 100
Last Answer : Answer: C
Description : The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above
Last Answer : (e) All of the above
Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above
Last Answer : (c) 15 percent
Description : Osmotic pressure of plasma is (A) 80–100 milliosmole/litre (B) 180–200 milliosmole/litre (C) 280–300 milliosmole/litre (D) 380–400 milliosmole/litre
Last Answer : Answer : C
Description : Normal serum glucagons level in fasting state varies between (A) 0-–10 pg/ml (B) 20–100 pg/ml (C) 200–300 pg/ml (D) 400–500 pg/ml
Last Answer : Answer : B
Description : The normal serum level of Ig A is (A) 100 mg% (B) 200 mg% (C) 300 mg% (D) 400 mg%
Description : In glycoproteins the carbohydrate is in the form of disaccharide units, the number of units are (A) 50–100 (B) 200–300 (C) 400–500 (D) 600–700
Last Answer : Answer : D
Description : Amylose contains glucose units (A) 100–200 (B) 200–300 (C) 300–400 (D) 500–600
Last Answer : C
Description : 3.0 ml of raw sewage is diluted to 300 ml. The D.O. concentration of the diluted sample at the beginning of the test was 8 mg/l. After 5 dayincubation at 20°C, the D.O. concentration was 5 mg/l. The BOD of raw sewerage is A. 100 mg/l B. 200 mg/l C. 300 mg/l D. 400 mg/l
Last Answer : ANS: C
Description : If a 2% solution of sewage sample is incubated for 5 days at 20°C and the dissolved oxygen depletion was found to be 8 mg/l. The BOD of the sewage is A. 100 mg/l B. 200 mg/l C. 300 mg/l D. 400 mg/l
Last Answer : ANS: D
Description : Number of satellites in geostationary orbits are A. 100 B. 200 C. 300 D. 400
Last Answer : 200
Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400
Last Answer : Large - L 300*250*200 Above 2.5 to 5 400
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Last Answer : Answer: Option D
Description : Transport of concrete by pumps, is done for a distance of (A) 100 m (B) 200 m (C) 300 m (D) 400 m
Last Answer : (D) 400
Description : Motorized knapsack sprayer blade rotation at about ……. To rev/min. a. 200 to 300. c. 100 to 120 b. 120 to 400. d. 150 to 300
Last Answer : 100 to 120