The ratio of the resistance of a 100 W, 220 V lamp to that of a 100 W, 110 V lamp will be nearly

by

1 Answer

Answer :

The ratio of the resistance of a 100 W, 220 V lamp to that of a 100 W, 110 V lamp will be nearly 4.

by

Related questions

If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly

Description : If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times 

Last Answer : If a 220 V heater is used on a 110 V supply, the heat produced by it will be significantly less than it would be if it were used on a 220 V supply. This is because the heater is designed to operate ... the heater, but it will be significantly less than it would be if it were used on a 220 V supply.

The resistance of a 100 W, 200 V lamp is

Last Answer : The resistance of a 100 W, 200 V lamp is 400 ohm.

The resistance of a 230 V, 100 W lamp is

Last Answer : The resistance of a 230 V, 100 W lamp is 529 Ω.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary ...

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be: 3.0 V

A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

Why is 440 V used for motors and 110/220 V used for lighting?

Description : Why is 440 V used for motors and 110/220 V used for lighting?

Last Answer : Motor load currents are large. Motors are 3-phase loads. A higher 440V voltage means lesser current for the same power and hence losses and size of cable wires is lower. Lighting is single phase ... small, hence lower voltage means less insulation in the cable wires. Ask E/O for more information

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : (C) 3.0 V.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be 3.0 V.

How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts

Description : How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts

Last Answer : Answer: B

The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Last Answer : Answer: B

The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: D

The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Last Answer : Answer: B

The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts

Last Answer : Answer: A

The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts

Last Answer : Answer: B

The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts

Last Answer : Answer: A

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... B. 160 W C. `37.5 W` D. 60 W

A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Description : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Last Answer : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of ... on, is A. 11 B. 22 C. 33 D. 66

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... `37.5` W B. 75W C. 80W D. 40 W

Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Description : Three bulbs are rating 40W 60W and 100W designed to work on 220V mains. Which bulb will burn most brightly if they are connected in series across 220 V mains? a. 40 W bulb b. 60 W blub c. 100 W blub d. all will burn equally brightly

Last Answer : a. 40 W bulb

A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms

Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms

Last Answer : Answer: D

A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms

Last Answer : Answer: D

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

A `100 V` voltmeter of internal resistance `20 k Omega` in series with a high resistance `R` is connected to a `110 V` line. The voltmeter reads `5 V`

Description : A `100 V` voltmeter of internal resistance `20 k Omega` in series with a high resistance `R` is connected to a `110 V` line. The voltmeter reads `5 V`

Last Answer : A `100 V` voltmeter of internal resistance `20 k Omega` in series with a high resistance `R` is ... B. `315kOmega` C. `420kOmega` D. `440kOmega`

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately...

Description : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: A. 385Ω B. 38.5Ω C. 3.1Ω D. 31Ω

Last Answer : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately equal to: 31Ω

Stuck my 110 volt computer into 220 volt! Did only the PSU burn?

Description : Stuck my 110 volt computer into 220 volt! Did only the PSU burn?

Last Answer : I would think probably only the PSU. If any of your components are fried, the PSU was probs designed badly.

I need a voltage adapter to convert 110 to 220 for a laptop.

Description : I need a voltage adapter to convert 110 to 220 for a laptop.

Last Answer : Apple sells a handy dandy World Travel Adapter Kit. $39.00

How can I install a 110 receptacle alongside a 220 receptacle using the 220 receptacle wires for power?

Description : How can I install a 110 receptacle alongside a 220 receptacle using the 220 receptacle wires for power?

Last Answer : While you can physically do this it violates the ElectricalCode. 110 Volt and 220 Volt receptacles are required by theElectrical Code to be on separate breakers for safety reasons, thiswould put them on the same 220 Volt breaker.

How much money you save with 220 volt Air Conditioners instead of 110 volt?

Description : How much money you save with 220 volt Air Conditioners instead of 110 volt?

Last Answer : It wont save you much at all this is more the type of wiring used. [email protected]

If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Last Answer : Answer: D

If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Description : If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Last Answer : Answer: C

If the line voltage to the controller shown in the illustration is 440 volts, what voltage is applied across the motor when contacts 'S' close? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Description : If the line voltage to the controller shown in the illustration is 440 volts, what voltage is applied across the motor when contacts 'S' close? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Last Answer : Answer: B

Compensation of letter and bulk bag of foreign articles are a) 220(60 gold francs) & 1110( 300 gold francs) b) 110(60 gold francs) & 1110( 300 gold francs) c) 200(60 gold francs) & 1000( 300 gold francs) d) None of the above

Description : Compensation of letter and bulk bag of foreign articles are a) 220(60 gold francs) & 1110( 300 gold francs) b) 110(60 gold francs) & 1110( 300 gold francs) c) 200(60 gold francs) & 1000( 300 gold francs) d) None of the above

Last Answer : b) It can be registered with an note that the deficiency would be collected from addresse

Anushiya covered a definite distance at some speed. If she had moved 5 kmph faster, she would have taken 55minutes less. If he had moved 4 kmph slower, she would have taken 55 minutes more. What is the distance in km? a) 110 Km b) 220 km c) 330 km d) 440 km

Description : Anushiya covered a definite distance at some speed. If she had moved 5 kmph faster, she would have taken 55minutes less. If he had moved 4 kmph slower, she would have taken 55 minutes more. What is the distance in km? a) 110 Km b) 220 km c) 330 km d) 440 km

Last Answer : C speed=2V1V2/(V1-V2) = 2*5*4/(5-4) =40 km/hr Distance= vt1 (1+v/v1) =40* 55/60(1+40/5) =40*11/12(1+8) =40*11/12*9 =330 km Therefore the distance is 330km

There are three 100 bulbs in parallel across 220 V.50 Hz line. If one bulb burns out:

Last Answer : There are three 100 bulbs in parallel across 220 V.50 Hz line. If one bulb burns out: Remaining two bulbs will produce light.

Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Description : Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Last Answer : c. 220V

What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Description : What is the resistance value indicated by the multimeter scale illustrated, if the range switch is set at R X 100, and the needle is at the position indicated by the letter 'Y'? EL-0047 A. 220 ohms B. 240 ohms C. 2,400 ohms D. 24,000 ohms

Last Answer : Answer: C

An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is

Description : An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately? A.385 ohms B.38.5ohms C.3.1 ohms D.31 ohms

Last Answer : 31ohns

In 1953, Sir Edmund Hillary and Tenzing Norgay were the first people to reach the summit of Mount Everest from their last previously established camp at an altitude of 27,900 feet (barometric pressure about 220 mm). At that camp, water would have: w) boiled at 100 degrees Celsius x) boiled at 68 degrees Celsius y) not boiled at any temperature z) sublimed

Description : In 1953, Sir Edmund Hillary and Tenzing Norgay were the first people to reach the summit of Mount Everest from their last previously established camp at an altitude of 27,900 feet (barometric pressure ... degrees Celsius x) boiled at 68 degrees Celsius y) not boiled at any temperature z) sublimed

Last Answer : ANSWER: X -- BOILED AT 68 DEGREES CELSIUS

What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is

Description : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Last Answer : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

Is the filament resistance lower or higher in a 500 watt light bulb than in a 100 watt light? Assume that both bulbs have been designed to operate at 110 volts.

Description : Is the filament resistance lower or higher in a 500 watt light bulb than in a 100 watt light? Assume that both bulbs have been designed to operate at 110 volts. 

Last Answer : ANSWER: LOWER

If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Description : If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Last Answer :  Each bulb when independently working will have currents (W/V= I)  For 200 Watt Bulb current (I200) =200/230=0.8696 A  For 100 Watt Bulb current (I100) =100/230=0.4348 A  ... current through it. So minimum power dissipated across it as min current X equal Voltage across =s min power dissipation

A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Description : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is connected in series, it works perfectly and the bulb

Last Answer : A filament bulb `(500 W, 100 V)` is to be used in a `230 V` main supply. When a resistance `R` is ... Omega` B. `46 Omega` C. `26Omega` D. `13 Omega`

Two electric bulbs rated 50 W and 100 W are glowing at full powr, when used in parallel with a battery of emf 120 V and internal resistance 10 `Omega`

Description : Two electric bulbs rated 50 W and 100 W are glowing at full powr, when used in parallel with a battery of emf 120 V and internal resistance 10 `Omega`

Last Answer : Two electric bulbs rated 50 W and 100 W are glowing at full powr, when used in parallel with a battery of emf 120 V ... power, is A. 6 B. 4 C. 2 D. 8

The sewage discharge in a detritus tank of a treatment plant is 576 litres/sec with flow velocity of 0.2 m/sec. If the ratio of width to depth is 2, the depth is A. 100 cm B. 110 cm C. 120 cm D. 150 cm

Description : The sewage discharge in a detritus tank of a treatment plant is 576 litres/sec with flow velocity of 0.2 m/sec. If the ratio of width to depth is 2, the depth is A. 100 cm B. 110 cm C. 120 cm D. 150 cm

Last Answer : ANS: C

A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

The ratio of spacing (d) for for simple cubic lattice, d(100) :d(110) :d(111) a. 1 : 0.707: 0.669 b. 1: 1.414: 0.577 c. 1: 0.707 : 0.577 d. 1: 0.707 : 1.154

Description : The ratio of spacing (d) for for simple cubic lattice, d(100) :d(110) :d(111) a. 1 : 0.707: 0.669 b. 1: 1.414: 0.577 c. 1: 0.707 : 0.577 d. 1: 0.707 : 1.154

Last Answer : c. 1: 0.707 : 0.577