How much money you save with 220 volt Air Conditioners instead of 110 volt?

1 Answer

Answer :

It wont save you much at all this is more the type of wiring used. [email protected]

Related questions

Description : Stuck my 110 volt computer into 220 volt! Did only the PSU burn?

Last Answer : I would think probably only the PSU. If any of your components are fried, the PSU was probs designed badly.

Description : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value by which the power would decrease is

Last Answer : If voltage across a bulb rated 220 volt-100 watt drops by `2.5 %` of its value, the percentage of the rated value ... 20%` B. `2.5%` C. `5%` D. `10%`

Description : Can you buy a refrigerator that uses 220 volt electricity?

Last Answer : General Electric makes and sells refrigerators that use 220 volt electricity. They are manufactured for use overseas, but are sold in the US as well.

Description : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

Last Answer : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: 245 volt

Description : I need a voltage adapter to convert 110 to 220 for a laptop.

Last Answer : Apple sells a handy dandy World Travel Adapter Kit. $39.00

Description : How can I install a 110 receptacle alongside a 220 receptacle using the 220 receptacle wires for power?

Last Answer : While you can physically do this it violates the ElectricalCode. 110 Volt and 220 Volt receptacles are required by theElectrical Code to be on separate breakers for safety reasons, thiswould put them on the same 220 Volt breaker.

Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Last Answer : Answer: D

Description : How many volts are necessary to provide a current of 10 amperes to a motor with an in-line resistance of 11 ohms? A. 21 volts B. 110 volts C. 220 volts D. 240 volts

Last Answer : Answer: B

Description : The turns ratio of transforme 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts

Last Answer : Answer: B

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: D

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts

Last Answer : Answer: B

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts

Last Answer : Answer: A

Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts

Last Answer : Answer: B

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts

Last Answer : Answer: C

Description : If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Last Answer : Answer: C

Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts

Last Answer : Answer: A

Description : If the line voltage to the controller shown in the illustration is 440 volts, what voltage is applied across the motor when contacts 'S' close? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Last Answer : Answer: B

Description : Compensation of letter and bulk bag of foreign articles are a) 220(60 gold francs) & 1110( 300 gold francs) b) 110(60 gold francs) & 1110( 300 gold francs) c) 200(60 gold francs) & 1000( 300 gold francs) d) None of the above

Last Answer : b) It can be registered with an note that the deficiency would be collected from addresse

Description : Why is 440 V used for motors and 110/220 V used for lighting?

Last Answer : Motor load currents are large. Motors are 3-phase loads. A higher 440V voltage means lesser current for the same power and hence losses and size of cable wires is lower. Lighting is single phase ... small, hence lower voltage means less insulation in the cable wires. Ask E/O for more information

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : (C) 3.0 V.

Description : Anushiya covered a definite distance at some speed. If she had moved 5 kmph faster, she would have taken 55minutes less. If he had moved 4 kmph slower, she would have taken 55 minutes more. What is the distance in km? a) 110 Km b) 220 km c) 330 km d) 440 km

Last Answer : C speed=2V1V2/(V1-V2) = 2*5*4/(5-4) =40 km/hr Distance= vt1 (1+v/v1) =40* 55/60(1+40/5) =40*11/12(1+8) =40*11/12*9 =330 km Therefore the distance is 330km

Description : If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times 

Last Answer : If a 220 V heater is used on a 110 V supply, the heat produced by it will be significantly less than it would be if it were used on a 220 V supply. This is because the heater is designed to operate ... the heater, but it will be significantly less than it would be if it were used on a 220 V supply.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be 3.0 V.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be: 3.0 V

Last Answer : The ratio of the resistance of a 100 W, 220 V lamp to that of a 100 W, 110 V lamp will be nearly 4.

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Description : What is represented by the solid dots within components 'B' and 'C' of the diagram shown in the illustration? (See illustration EL-0081) EL-0081 A. The fact that these parts are subject to wear and ... only. C. The particular components contain a gas such as neon or argon. D. All of the above.

Last Answer : Answer: C

Description : The doorbell on your house requires a 12 volt alternating current. A transformer having a primary winding of 1,600 turns is to be used to step down your house's 110-volt alternating current. How many turns are there on the secondary winding?

Last Answer : ANSWER: 175 TURNS 

Description : Why didn't GM use a small Diesel instead of a gas engine in the Volt?

Last Answer : answer:Actually diesel currently tends to be more expensive. But I would assume they went with gas because it is your average everyday americans fuel of choice. Plus the engines don't wear ... though if you see volts featuring diesel secondary engines at some point though, especially in Europe.

Description : [23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Last Answer : C. Total transformer loss depends on volt ampere

Description : What is the max square feet or cubic feet for residential air conditioners?

Last Answer : JLeslie This Link seems to keep is simple and I like that it is tabled by temp zones.

Description : Can you help me get information on solar powered portable air conditioners?

Last Answer : Wow, such a thing exists? It takes a lot of power to run the compressor and fans on an air conditioner, your solar array will be bigger than the roof over that room.

Description : Why are large air conditioners so delicate?

Last Answer : answer:A couple things could be going on. Power failures in general should not be the cause of total equipment failure and more often will cause electrical issues that should only require electrical components to ... a year and twice a year lubing of the drive shafts is minimum for our roof tops.

Description : Do you think the government should supply air conditioners for the poor?

Last Answer : In extreme heat waves, most communities seem to have shelters available.

Description : In humid city's in the USA and other countries do most homes have air conditioners?

Last Answer : It seems like most people have air conditioners in Philly.

Description : Why do human beings have to go for Pee often, when they sit under air conditioners?

Last Answer : I would like to see the research you conducted here…

Description : Give reasons : Air conditioners should be installed at the top window. -Science-7

Last Answer : As a fact that warm air is much lighter than the cold air, so being heavier the cold air from air conditioner moves downwards while the hot air moves upwards and gets cooled and come downwards once again and cools the room.

Description : What are the different types of air conditioners?

Last Answer : There are eight main types of air conditioning equipment out there in the market. Each type of air conditioner is designed for a certain space & fulfills a certain purpose. The different AC types ... offer 24 hour emergency air conditioner and heater repair services. contact no (951) 772-3741.

Description : What are the refrigerants used in Air Conditioners?

Last Answer : Hydrofluorocarbons. Specifically, R410A and R134. Some systems still use hydrochloroflourocarbons, which contain chlorine, but this is much worse for the environment, and isn't as efficient, so it's expected to be completely phased out by 2020.

Description : How Air conditioners are harmful to human beings?

Last Answer : Air conditioning is not directly harmful. It has always been known that families living in air conditioned houses make more babies than families without it. When you move to a hot climate your body has to ... quite uncomfortable when he has to go outside again. It is possible to die as a result.

Description : It is used in refrigerator and air conditioners and it is a source of `Cl^(-)` :

Last Answer : It is used in refrigerator and air conditioners and it is a source of `Cl^(-)` : A. Benzene B. `CH_(4)` C. Benzopyrene D. Freon.

Description : A Guide to Portable Air Conditioners?

Last Answer : Central air conditioning is not a viable option for manyconsumers, but there are several different types of portable airconditioners that will deliver impressive results if they arechosen properly. Because every individual ... like the look of a unit protruding from awindow of their home, and the f

Description : Who makes the best air conditioners in the US?

Last Answer : There are several companies that make air conditioners. Newer models have the same advanced features quality is also dependent on price level so it is hard to say who makes the best air conditioners.

Description : I am comparing the LG 8000 BTU and the Zenith 6500 BTU window air conditioners, my room is 20 X 24, which would cool more efficiently?

Last Answer : LG 8000 BTU would cool more efficiently