A chopper operating at a fixed frequency is feeding an R-L load. As they duty ratio of the chopper is increased...

A chopper operating at a fixed frequency is feeding an R-L load. As they duty ratio of the chopper is increased from 25% to 75%, the ripple in the load current.
by

1 Answer

Answer :

Remains constant.

by

Related questions

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:

Description : Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

Last Answer : Ripple in output current of step down Chopper feeding a RLE load is maximum, when duty cycle is equal to 0.5

A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while

Description : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would  (1) increase progressively  (2 ... 0.5 and then increase  (4) increase to a maximum value at α = 0.5 and then decrease

Last Answer : A dc chopper is fed from a constant voltage mains the duty ratio of chopper is progressively increased while the chopper feeds an RL load. The per unit current ripple would increase to a maximum value at α = 0.5 and then decrease

On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Description : On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Last Answer : (C) Increased reflux ratio

why the feeding frequency to a microprocessor s twice the operating frequency.

Description : why the feeding frequency to a microprocessor s twice the operating frequency.

Last Answer : Ans-since 8085 microprocessor operating frequency 5 mega hz but operating frequency is 10 mega hz because crystal effect in processor

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

What are the disadvantages of load commutated chopper?

Description : What are the disadvantages of load commutated chopper?

Last Answer : a. For high power applications, efficiency becomes very low because of high switching losses at high operating frequencies. b. Freewheeling diode is subjected to twice the supply voltage. c ... other pair is commutated. This can be realized by sensing the capacitor current that is alternating.

What are the advantages of load commutated chopper?

Description : What are the advantages of load commutated chopper?

Last Answer : a. Commutating inductor is not required. b. It is capable of commutating any amount of load current. c. It can work at high frequencies in the order of kHz. d. Filtering requirements are minimal.

A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased

Description : A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased A) The phase displacement will increase B) The phase displacement will decrease C) The phase displacement will not change D) The surge impedance will increase

Last Answer : A transmission line is operating with a Phase shift of 80° between two ends. If the load is suddenly increased The phase displacement will increase

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Description : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is

Last Answer : Total instantaneous power supplied by a 3-phase ac supply to a balanced R-L load is constant

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are

Description : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

Last Answer : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is 500 Hz

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Description : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Last Answer : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of L or C.

δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIL) is the value of deflection for ______ A. simply supported beam which has central point load B. simply supported beam which has eccentric point load C. simply supported beam which has U.D.L. point load per unit length D. fixed beam which has central point load

Last Answer : B. simply supported beam which has eccentric point load

δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Description : δ = (W a 2 b 2 ) / (3 EIl) is the value of deflection for ______ a. simply supported beam which has central point load b. simply supported beam which has eccentric point load c. simply supported beam which has U.D.L. point load per unit length d. fixed beam which has central point load

Last Answer : b. simply supported beam which has eccentric point load

According to Euler’s column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends. (a) equal to (b) two times (c) four times (d) eight times

Description : According to Euler’s column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends. (a) equal to (b) two times (c) four times (d) eight times

Last Answer : (c) four times

For a fixed beam with midpoint load point moment for x<L/2 is a. P/4(8x-L) b. P/8(4x-L) c. P/8(L-4x) d. P/4(L-4x)

Description : For a fixed beam with midpoint load point moment for x

Last Answer : b. P/8(4x-L)

.For a fixed beam with midpoint load point of contraflexure occurs at a. L/4 b. L/2 c. L/6 d. L/8

Description : .For a fixed beam with midpoint load point of contraflexure occurs at a. L/4 b. L/2 c. L/6 d. L/8

Last Answer : a. L/4

In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end

Last Answer : (b) Wl at the fixed end

The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. changing the RPM of the rotor flux C. changing the phase sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity

Description : The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. ... sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity

Last Answer : Answer: A

The speed of a three-phase squirrel-cage induction-type motor operating in a fixed frequency system is varied by changing the _____________. A. number of phases to the motor B. number of stator poles C. locked rotor current D. resistance of the rotor winding

Description : The speed of a three-phase squirrel-cage induction-type motor operating in a fixed frequency system is varied by changing the _____________. A. number of phases to the motor B. number of stator poles C. locked rotor current D. resistance of the rotor winding

Last Answer : Answer: B

In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load

Description : In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load  (A) The armature current increases and the power factor decreases  (B) The armature ... but is lagging  (D) The armature current decreases and the power factor increases and is leading

Last Answer : In a synchronous generator if the excitation increased from a low value to normal value, with a fixed load The armature current decreases and the power factor increases and is leading

Which term is not related to banking? (1) C.R.R. (2) N .E.E .R. (3) S.L.R. (4) Fixed Deposits

Description : Which term is not related to banking? (1) C.R.R. (2) N .E.E .R. (3) S.L.R. (4) Fixed Deposits

Last Answer : (2) N.E.E.R. Explanation: NEER stands for Nominal Effective Exchange Rate which represents the relative value of a home country's currency compared to the other major currencies being traded (U.S. ... etc.). It also represents the approximate relative price a consumer will pay for an imported good.

Which term is not related to banking ? (1) C.R.R. (2) N.E.E.R. (3) S.L.R. (4) Fixed Deposits

Description : Which term is not related to banking ? (1) C.R.R. (2) N.E.E.R. (3) S.L.R. (4) Fixed Deposits

Last Answer : N.E.E.R.

The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated

Description : The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated load resistance of 450 Ohm are given by  (a) 57.3 mH; 0.283 μF (b) 28.66 μH; 0.14 μF (c) 114.64 mH; 0.566 mF (d) 50.23 mH; 0.632 mF

Last Answer : The values of L and C for a low pass filter with cut off frequency of 2.5 KHz and operating with a terminated load resistance of 450 Ohm are given by 57.3 mH; 0.283 μF

If the excitation of an alternator operating in parallel is decreased below normal, its _____________. A. power factor will change in the lagging direction B. power factor will change in the leading direction C. ampere load will be greatly increased D. kilowatt load will be greatly decreased

Description : If the excitation of an alternator operating in parallel is decreased below normal, its _____________. A. power factor will change in the lagging direction B. power factor will change in the leading direction C. ampere load will be greatly increased D. kilowatt load will be greatly decreased

Last Answer : Answer: B

If the excitation is increased to one of two alternators operating in parallel, the _____________. A. power factor will change in the lagging direction B. power factor will change in the leading direction C. kilowatt load will be greatly increased D. ampere load will be greatly decreased

Description : If the excitation is increased to one of two alternators operating in parallel, the _____________. A. power factor will change in the lagging direction B. power factor will change in the leading direction C. kilowatt load will be greatly increased D. ampere load will be greatly decreased

Last Answer : Answer: A

A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Description : A synchronous motor is operating on no-load at unity power factor. If the field current is increased, power factor will become (A) Leading & current will decrease (B) Lagging & current will increase. (C) Lagging & current will decrease. (D) Leading & current will increase.

Last Answer : Ans: A Initially synchronous motor is operating at no load and unity power factor. When field current increases, the excitation will increase. Therefore, p.f will be leading and current will be I CosΦ < I

Under certain circumstances, the gut may become a source of sepsis and serve as the motor of systemic inflammatory response syndrome. Microbial translocation is the process by which microorganisms migrate across the mucosal barrier to invade the host. Which of the following mechanisms can promote bacterial translocation? a. An increased number of gut bacteria b. Altered intestinal mucosal permeability c. Decreased host defense mechanisms d. Lack of enteral feeding

Description : Under certain circumstances, the gut may become a source of sepsis and serve as the motor of systemic inflammatory response syndrome. Microbial translocation is the process by which microorganisms ... intestinal mucosal permeability c. Decreased host defense mechanisms d. Lack of enteral feeding

Last Answer : Answer: a, b, c, d 99 Translocation is promoted in three general ways: 1) altered permeability of the intestinal mucosa as caused by shock, sepsis, distant injury, or cell toxins; 2) ... trauma patient d. Fifty percent of non-nitrogen caloric requirements should be provided in the form of fat

The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Description : The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging

Last Answer : ANSWER : D

For a cold dilute feed to produce thick viscous liquor, backward feeding as compared to forward feeding results in (A) Increased economy (B) Decreased economy (C) Lower capacity (D) No effect on economy

Description : For a cold dilute feed to produce thick viscous liquor, backward feeding as compared to forward feeding results in (A) Increased economy (B) Decreased economy (C) Lower capacity (D) No effect on economy

Last Answer : (A) Increased economy

For hot feed, forward feeding as compared to backward feeding results in __________ economy. (A) Increased (B) Decreased (C) No effect on (D) None of these

Description : For hot feed, forward feeding as compared to backward feeding results in __________ economy. (A) Increased (B) Decreased (C) No effect on (D) None of these

Last Answer : (A) Increased

When two generators are on the line and are sharing the load equally, they are said to be operating in _____________. A. frequency B. series C. parallel D. resonance

Description : When two generators are on the line and are sharing the load equally, they are said to be operating in _____________. A. frequency B. series C. parallel D. resonance

Last Answer : Answer: C

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Description : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is

Last Answer : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is 0.707 lead

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

For a fixed number of ideal stages in a distillation column, as the reflux ratio is increased, the difference in composition between the top and bottomproduct streams(A) Increases(B) Decreases(C) Remain unaffected(D) Passes through a maximum

Description : For a fixed number of ideal stages in a distillation column, as the reflux ratio is increased, the difference in composition between the top and bottom product streams (A) Increases (B) Decreases (C) Remain unaffected (D) Passes through a maximum

Last Answer : (A) Increases

Few items of P/L A/c of a company are– Sales – Rs.1,60,000 Closing stock – Rs.38,000 Non-operating Expenses – Rs.800 Non-operating Income – Rs.4,800 Net Profit – Rs.28,000 What is the Operating Profit Ratio ? (A) 18% (B) 20% (C) 15% (D) 57%

Description : Few items of P/L A/c of a company are– Sales – Rs.1,60,000 Closing stock – Rs.38,000 Non-operating Expenses – Rs.800 Non-operating Income – Rs.4,800 Net Profit – Rs.28,000 What is the Operating Profit Ratio ? (A) 18% (B) 20% (C) 15% (D) 57%

Last Answer : Answer: 15%

The ripple content of load current of a converter feeding RL load is decided by

Description : The ripple content of load current of a converter feeding RL load is decided by  A) Load resistance alone B) Load inductance alone C) Both load resistance and load inductance D) Neither resistance nor inductance

Last Answer : The ripple content of load current of a converter feeding RL load is decided by Both load resistance and load inductance

A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load

Description : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component ... (B) 31% and 7.8 A (C) 66% and 6.8 A (D) 66% and 7.8 A

Last Answer : A three phase fully controlled bridge converter is feeding a load drawing a constant and ripple free load current of 10 A at a firing angle of 30o. The approximate Total harmonic Distortion (%THD) and the rms value of fundamental component of input current will respectively be 31% and 7.8 A

A stand alone engine driven synchronous generator is feeding a partly inductive load. A capacitor is now

Description : A stand alone engine driven synchronous generator is feeding a partly inductive load. A capacitor is now connected across the load to completely nullify the inductive current. For this operating condition.  ... left unaltered (D) the field current has to be reduced and fuel input left unaltered

Last Answer : A stand alone engine driven synchronous generator is feeding a partly inductive load. A capacitor is now connected across the load to completely nullify the inductive current. For this operating condition.  the field current has to be reduced and fuel input left unaltered

A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction

Description : A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction is  (A) magnetizing (B) demagnetizing (C) cross-magnetizing (D) ineffective

Last Answer : A synchronous generator is feeding a zero power factor (lagging) load at rated current. The armature reaction is demagnetizing 

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

Two AC generators of the same capacity are operating in parallel. One with a zero speed droop setting and the other with a 5% speed droop. If its capacity is not exceeded, the unit whose governor has the zero speed droop setting will _____________. A. assume the smaller share of the load B. maintain the frequency of the system C. have poor sensitivity characteristics D. have poor power response

Description : Two AC generators of the same capacity are operating in parallel. One with a zero speed droop setting and the other with a 5% speed droop. If its capacity is not exceeded, the unit whose ... B. maintain the frequency of the system C. have poor sensitivity characteristics D. have poor power response

Last Answer : Answer: B

A change in field excitation of an alternator operating in parallel will cause a change in its _____________. A. alternator frequency B. kilowatt load C. voltage output D. all of the above

Description : A change in field excitation of an alternator operating in parallel will cause a change in its _____________. A. alternator frequency B. kilowatt load C. voltage output D. all of the above

Last Answer : Answer: C

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power

Description : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, ... system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

Last Answer : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is 50 Hz

As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first and then more and more rapidly (C) Total cost first decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Description : As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first ... decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Last Answer : (C) Total cost first decreases and then increases

The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Description : The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Last Answer : (c) adjusting the governor

When an AC voltage, of variable frequency is applied to series L-C-R circuit, the current in the cirucit is the same at 4kHz. The current in the cirui

Description : When an AC voltage, of variable frequency is applied to series L-C-R circuit, the current in the cirucit is the same at 4kHz. The current in the cirui

Last Answer : When an AC voltage, of variable frequency is applied to series L-C-R circuit, the current in the cirucit ... is maximum at (x)kHz. Find the value of x