In a precision planter the height of seed drop: A. Should be as close to be ground level as is possible. B. Should be at least 1 m from the ground level. C. Is not a factor to be considered? D. None of These

In a precision planter the height of seed drop:
A. Should be as close to be ground level as is possible.
B. Should be at least 1 m from the ground level.
C. Is not a factor to be considered?
D. None of These
by

1 Answer

Answer :

A. Should be as close to be ground level as is possible.
by

Related questions

The precision planter is: A. Seed drill B. Broadcaster C. Dibbler D. Dofaan

Description : The precision planter is: A. Seed drill B. Broadcaster C. Dibbler D. Dofaan

Last Answer : Dibbler

n the following the precision planter is: A. seed drill B. broadcaster C. Dibbler D. dofaan

Description : n the following the precision planter is: A. seed drill B. broadcaster C. Dibbler D. dofaan

Last Answer : C. Dibble

The Height Gauge for a level crossing should be located at least --------- from the gate post a) 3 meters b) 5 meters c) 8 meters* d) 10 meters

Description : The Height Gauge for a level crossing should be located at least --------- from the gate post a) 3 meters b) 5 meters c) 8 meters* d) 10 meters

Last Answer : c) 8 meters*

Height of Low level platform for passengers for BG is --- high (a) 0.455 m* (b) 0.560 m (c) 0.650 m (d) 0.760 m

Description : Height of Low level platform for passengers for BG is --- high (a) 0.455 m* (b) 0.560 m (c) 0.650 m (d) 0.760 m

Last Answer : (a) 0.455 m*

Height of high level platform for passengers for BG is --- high (a) 0.455 m (b) 0.560 m (c) 0.650 m (d) 0.760 m*

Description : Height of high level platform for passengers for BG is --- high (a) 0.455 m (b) 0.560 m (c) 0.650 m (d) 0.760 m*

Last Answer : (d) 0.760 m*

The height of formation depends upon the a) Ground contours and the gradient adopted* b) Ground contour only c) Gradient adopted only d) Rainfall intensity over the year

Description : The height of formation depends upon the a) Ground contours and the gradient adopted* b) Ground contour only c) Gradient adopted only d) Rainfall intensity over the year

Last Answer : a) Ground contours and the gradient adopted*

Height gauges should be located at a minimum distance of….. from gate post. (a) 5 m (b) 7.5m (c) 8m* (d)10m

Description : Height gauges should be located at a minimum distance of….. from gate post. (a) 5 m (b) 7.5m (c) 8m* (d)10m

Last Answer : (c) 8m*

Height of platform of a flag station in cutting above rail level is (a) Same height as Rail level (b) 305 mm above rail level (c) 455 mm above rail level (d) 840mm above rail level*

Description : Height of platform of a flag station in cutting above rail level is (a) Same height as Rail level (b) 305 mm above rail level (c) 455 mm above rail level (d) 840mm above rail level*

Last Answer : (d) 840mm above rail level*

Maximum height of low level cistern from top of W.C. pan should be (a) 65 cm. (b) 30 cm. (c) 8 (d) 120 cm. (e) 80 cm.

Description : Maximum height of low level cistern from top of W.C. pan should be (a) 65 cm. (b) 30 cm. (c) 8 (d) 120 cm. (e) 80 cm.

Last Answer : b) 30 cm. (c) 8

For Box Culverts Danger level is to be taken as a) at the top of slab b)one third height below bottom of slab c) at the bottom of slab* d) None of the above

Description : For Box Culverts Danger level is to be taken as a) at the top of slab b)one third height below bottom of slab c) at the bottom of slab* d) None of the above

Last Answer : c) at the bottom of slab*

The maximum height above rail level for B.G. goods platform is ……. Mm (a) 1000mm (b) 1050mm (c) 1065mm* (d) 1075mm

Description : The maximum height above rail level for B.G. goods platform is ……. Mm (a) 1000mm (b) 1050mm (c) 1065mm* (d) 1075mm

Last Answer : (c) 1065mm*

What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Description : What is maximum height above rail level for low-level passenger platform for BG? (a) 300mm (b) 455mm* (c) 525mm (d) 550mm

Last Answer : (b) 455mm

Maximum height above rail level of high passenger Platform a. 860 mm b. 900 mm c. 840 mm&* d. 875 mm

Description : Maximum height above rail level of high passenger Platform a. 860 mm b. 900 mm c. 840 mm&* d. 875 mm

Last Answer : c. 840 mm&*

The bottom of side drains should be below the formation level by at least------------ a) 45 cm b )30 cm* c) 15 cm d) 60 cm

Description : The bottom of side drains should be below the formation level by at least------------ a) 45 cm b )30 cm* c) 15 cm d) 60 cm

Last Answer : b )30 cm*

The difference between seed drill and planter is a) Variation in hill to hill spacing b) Number of seed per hill is more uniform in planter c) Seed delivery tube d) Furrow opener e) Both a and b Ans. e

Description : The difference between seed drill and planter is a) Variation in hill to hill spacing b) Number of seed per hill is more uniform in planter c) Seed delivery tube d) Furrow opener e) Both a and b Ans. e

Last Answer : ans e

Uniformity measure of a planter is a) Equal seed spacing b) Equal number of seed dropped per hill c) Minimum variation in different openers d) All of the above Ans. d

Description : Uniformity measure of a planter is a) Equal seed spacing b) Equal number of seed dropped per hill c) Minimum variation in different openers d) All of the above Ans. d

Last Answer : ans d

Blower is part of: A. Planter. B. Zero till drill C. Pneumatic seed drill D. Till plant machine

Description : Blower is part of: A. Planter. B. Zero till drill C. Pneumatic seed drill D. Till plant machine

Last Answer : Pneumatic seed drill

The equipment used for dropping seeds in a continuous stream and the spacing between plant to plant in a row is not constant is: A. Seed drill B. Planter C. Trans planter D. All are correct

Description : The equipment used for dropping seeds in a continuous stream and the spacing between plant to plant in a row is not constant is: A. Seed drill B. Planter C. Trans planter D. All are correct

Last Answer : Seed drill

Dibbler is a: A. Seed drill B. Planter C. Trans planter D. None of these

Description : Dibbler is a: A. Seed drill B. Planter C. Trans planter D. None of these

Last Answer : Planter

Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter

Description : Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter

Last Answer : d) Transplanter

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm

Description : n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm

Last Answer : b) 600 mm*

In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm

Description : In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm

Last Answer : c) 450 mm*

Can you start a clematis in planter and transfer to ground?

Description : Can you start a clematis in planter and transfer to ground?

Last Answer : Need Answer

Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from the metering device within a few centimetres of the furrow bottom. (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Last Answer : d) All of the above.

The commonly used power transmission system in ferti seed drills are: a) China-sprocket and gears b) Gears and belt pulleys c) Belt pulleys and cams d) Belt pulleys and chain sprocket

Description : The commonly used power transmission system in ferti seed drills are: a) China-sprocket and gears b) Gears and belt pulleys c) Belt pulleys and cams d) Belt pulleys and chain sprocket

Last Answer : d) Belt pulleys and chain sprocket

In order to do fly levelling the following type of methodology is adopted (a) Rise & fall method (b) Height of instrument method (c) Both the above* (d) None of the above

Description : In order to do fly levelling the following type of methodology is adopted (a) Rise & fall method (b) Height of instrument method (c) Both the above* (d) None of the above

Last Answer : c) Both the above*

The wash hand basin shall be fixed at a height of (a) 75-80 cm* (b) 75 cm (c) 80 cm (d) Not specified

Description : The wash hand basin shall be fixed at a height of (a) 75-80 cm* (b) 75 cm (c) 80 cm (d) Not specified

Last Answer : (a) 75-80 cm*

Defect of High joint is due to ? (i) Early trimming of weld (ii) Excess provision of height during alignment.* (iii) Early grinding of weld (iv) None of above

Description : Defect of High joint is due to ? (i) Early trimming of weld (ii) Excess provision of height during alignment.* (iii) Early grinding of weld (iv) None of above

Last Answer : (ii) Excess provision of height during alignment.

Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

Description : Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

Last Answer : (iv) Nil/Less provision of height during alignment.

Which gauge is used to measure the height of rail at the time of aligning of rails for AT welding? (i) Height gauge.* (ii) Vertical gauge (iii) Horizontal gauge (iv) As decided by site supervisor

Description : Which gauge is used to measure the height of rail at the time of aligning of rails for AT welding? (i) Height gauge.* (ii) Vertical gauge (iii) Horizontal gauge (iv) As decided by site supervisor

Last Answer : (iv) As decided by site supervisor

Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Description : Torch is kept at height from top surface of rail head? (i) 30 to 55 mm (ii) 35 to 40 mm (iii) 40 to 45 mm

Last Answer : (iii) 40 to 45 mm

Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm

Description : Height of crucible is kept from top surface of mould? (i) 30 mm (ii) 40 mm (iii) 50 mm* (iv) 60 mm

Last Answer : (iii) 50 mm*

Facia boards of platform shelters shall have a minimum horizontal clearance of ……. from C.L. of track at a minimum height of 4.61m above RL. a) 2360 mm b) 3660 mm c) 3000 mm d) 1600 mm*

Description : Facia boards of platform shelters shall have a minimum horizontal clearance of ……. from C.L. of track at a minimum height of 4.61m above RL. a) 2360 mm b) 3660 mm c) 3000 mm d) 1600 mm*

Last Answer : d) 1600 mm*

The height gauge need to be provided in a) ROB b) RUB* c) FOB d) Fly Over

Description : The height gauge need to be provided in a) ROB b) RUB* c) FOB d) Fly Over

Last Answer : b) RUB*

Maximum height of rolling stock on BG should be (a) 2745mm (b) 3250mm (c) 3450mm (d) 4140mm*

Description : Maximum height of rolling stock on BG should be (a) 2745mm (b) 3250mm (c) 3450mm (d) 4140mm*

Last Answer : (d) 4140mm*

What is the height of 60 kg rail section? a. 180 mm b. 172 mm* c. 185 mm d. 165 mm

Description : What is the height of 60 kg rail section? a. 180 mm b. 172 mm* c. 185 mm d. 165 mm

Last Answer : b. 172 mm*

Sensitivity calibration against temp. variation shall be carried out. (i) At least once in month* (ii) quarterly. (iii) at least once in six months (iv) Any of above.

Description : Sensitivity calibration against temp. variation shall be carried out. (i) At least once in month* (ii) quarterly. (iii) at least once in six months (iv) Any of above.

Last Answer : i) At least once in month*

………….. soil has the least SBC of the soil. a) Hard moorum b) Stiff clay c) Black cotton soil* d) Soft rock

Description : ………….. soil has the least SBC of the soil. a) Hard moorum b) Stiff clay c) Black cotton soil* d) Soft rock

Last Answer : c) Black cotton soil*

Deep screening of entire track must be done at least:- (a) Once in a quarter. (b) Once in a year. (c) Once in 5 years. (d) Once in 10 years.*

Description : Deep screening of entire track must be done at least:- (a) Once in a quarter. (b) Once in a year. (c) Once in 5 years. (d) Once in 10 years.*

Last Answer : (d) Once in 10 years.*

In a precise diet and nutrition study, you need to determine the average weight and average height of a group each to a precision of 1%. The minimum sample size required is w) 10 x) 100 y) 1000 z) 10,000

Description : In a precise diet and nutrition study, you need to determine the average weight and average height of a group each to a precision of 1%. The minimum sample size required is w) 10 x) 100 y) 1000 z) 10,000 

Last Answer : ANSWER: Z -- 10,000 

On a project the project manager should strive for a "Quality Level" that : 1. is the highest level possible 2. is as close to the project objectives as possible 3. represents the least cost to the project. 4. Exceeds the specified requirements of the project.

Description : On a project the project manager should strive for a "Quality Level" that : 1. is the highest level possible  2. is as close to the project objectives as possible  3. represents the least cost to the project.  4. Exceeds the specified requirements of the project.

Last Answer : 2. is as close to the project objectives as possible

The shadow of a tower standing on level ground is found to be 40 m longer when the Sun’s altitude is 30° than when it is 60°. Find the height of the tower. -Maths 9th

Description : The shadow of a tower standing on level ground is found to be 40 m longer when the Sun’s altitude is 30° than when it is 60°. Find the height of the tower. -Maths 9th

Last Answer : this is the answer

Settlement of foundations or Tilted piers and abutments will be considered as distressed bridge as a) Group I* b) Group II c) Both of the above d) None of the above

Description : Settlement of foundations or Tilted piers and abutments will be considered as distressed bridge as a) Group I* b) Group II c) Both of the above d) None of the above

Last Answer : a) Group I*

In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per 30 metre tape duly corrected for temperature, slope and sag, the angular error of closure not to exceed (where n is the number of traverse legs) (A) 50" n(B) 30" n(C) 60" n (D) None of these

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such operations c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR d. An approach using bearing, elevation, and, optionally, distance information

Description : A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such operations c. An ... by an ILS or a PAR d. An approach using bearing, elevation, and, optionally, distance information

Last Answer : c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such operations c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

Description : A precision Approach Procedure is defined as: a. An approach using bearing, elevation and distance information b. An approach with a crew of at least 2 pilots trained for such ... An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

Last Answer : c. An instrument approach procedure utilizing azimuth and glide path information provided by an ILS or a PAR

Formula for average service life of belt at a given speed is a) Life(hrs)= [ Belt length (mm)/ Total fatique rates]*100 b) Life(hrs)=[Total fatique rates / Belt length (mm)]*100 c) Life(hrs)=[Belt length (m)/ Total fatique rates]*100 d) None of the above

Description : Formula for average service life of belt at a given speed is a) Life(hrs)= [ Belt length (mm)/ Total fatique rates]*100 b) Life(hrs)=[Total fatique rates / Belt length (mm)]*100 c) Life(hrs)=[Belt length (m)/ Total fatique rates]*100 d) None of the above

Last Answer : a) Life(hrs)= [ Belt length (mm)/ Total fatique rates]*100

Size of cubicle of a booking office is kept as (a) 1.20 x 1.50 m (b) 1.50 x 1.20 m (c) 1.50 x 1.80 m (d) 1.80 x 1.50 m*

Description : Size of cubicle of a booking office is kept as (a) 1.20 x 1.50 m (b) 1.50 x 1.20 m (c) 1.50 x 1.80 m (d) 1.80 x 1.50 m*

Last Answer : (d) 1.80 x 1.50 m*

For new lines, width of formation in bank for N.G single line is (a) 3.35 m (b) 3.70 m* (c ) 5.25 m (e) 5.85 m

Description : For new lines, width of formation in bank for N.G single line is (a) 3.35 m (b) 3.70 m* (c ) 5.25 m (e) 5.85 m

Last Answer : b) 3.70 m*