The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the  forward speed of the planter
b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b)
d) None of the above
by

1 Answer

Answer :

c) Both (a) and (b)
by

Related questions

Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from the metering device within a few centimetres of the furrow bottom. (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Description : Variation in the drop size of seed can be minimised by (a) Using a short, smooth, small diameter tube with the discharge end close to bottom of furrow. (b) Discharging the seed directly from ... (c) Mechanically transferring the seeds from the metering unit in the furrow. (d) All of the above.

Last Answer : d) All of the above.

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

Seed drill uniformity can be measured by a) Number of seed per rotation of metering unit b) Spacing between seeds c) a and b both d) none of these Ans. c

Description : Seed drill uniformity can be measured by a) Number of seed per rotation of metering unit b) Spacing between seeds c) a and b both d) none of these Ans. c

Last Answer : ans c

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism

Last Answer : (d) Inclined plate metering mechanism

The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Description : The metering mechanism which is suitable for the metering of small seeds as well as large grains. (a) Internal double run mechanism (b) Fluted wheel mechanism (c) Stationary opening with auger (d) None of the above

Last Answer : (a) Internal double run mechanism

The equipment used for dropping seeds in a continuous stream and the spacing between plant to plant in a row is not constant is: A. Seed drill B. Planter C. Trans planter D. All are correct

Description : The equipment used for dropping seeds in a continuous stream and the spacing between plant to plant in a row is not constant is: A. Seed drill B. Planter C. Trans planter D. All are correct

Last Answer : Seed drill

Seed drills differ from the planters in respect of a) metering mechanism b) ground wheel design c) transmission system between ground wheel and roller wheel d) none of the above

Description : Seed drills differ from the planters in respect of a) metering mechanism b) ground wheel design c) transmission system between ground wheel and roller wheel d) none of the above

Last Answer : a) metering mechanism

Planters differ from a seed drill in respect of- (A) kind of power transmission system (B)kind of metering mechanism (C)kind of furrow opener used (D)all of the above

Description : Planters differ from a seed drill in respect of- (A) kind of power transmission system (B)kind of metering mechanism (C)kind of furrow opener used (D)all of the above

Last Answer : (B)kind of metering mechanism

The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Description : The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Last Answer : b. Fluted wheel mechanism

n the following the precision planter is: A. seed drill B. broadcaster C. Dibbler D. dofaan

Description : n the following the precision planter is: A. seed drill B. broadcaster C. Dibbler D. dofaan

Last Answer : C. Dibble

Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter

Description : Equipment for placing seeding in the soil called: a) Seed drill b) Seed cum fertilizer drill c) Planter d) Transplanter

Last Answer : d) Transplanter

Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Description : Cleaning of sugarcane is obtained at peripheral speed A. 12-15m/sec B. 18-20m/sec C. 20-25m/sec D. 25-30m/sec

Last Answer : B. 18-20m/sec

Closer group spacing and accurate hill spacing is obtained with a) Rotary valve b) Transfer wheel c)Both a & b d)All of the above

Description : Closer group spacing and accurate hill spacing is obtained with a) Rotary valve b) Transfer wheel c)Both a & b d)All of the above

Last Answer : c)Both a & b

In check rowing the seed spacing is a. constant b. continuous c. same as the rows d. none of these

Description : In check rowing the seed spacing is a. constant b. continuous c. same as the rows d. none of these

Last Answer : c. same as the rows

The difference between seed drill and planter is a) Variation in hill to hill spacing b) Number of seed per hill is more uniform in planter c) Seed delivery tube d) Furrow opener e) Both a and b Ans. e

Description : The difference between seed drill and planter is a) Variation in hill to hill spacing b) Number of seed per hill is more uniform in planter c) Seed delivery tube d) Furrow opener e) Both a and b Ans. e

Last Answer : ans e

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Description : Cut-off device is not required with (a) Inclined plate metering (b) Horizontally plate metering (c) Vertically plate metering (d) All of the above

Last Answer : (a) Inclined plate metering

Most commonly used for the metering mechanism for fertilizer a. Spur wheel b. Serrated wheel c. Star wheel d. Auger type

Description : Most commonly used for the metering mechanism for fertilizer a. Spur wheel b. Serrated wheel c. Star wheel d. Auger type

Last Answer : a. Spur wheel

Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Description : Capacity of field choppers (chaff cutter) is affected by.... (a) Capacity of the feed mechanism (cross-sectional area) (b) Rate of advance of material through throat considered as to be same linear speed of feed mechanism (c) Density of forage material (d) All of the above

Last Answer : (d) All of the above

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Description : In a horizontal plate type planter maximum obtainable value of cell fill is : A.Greater then 100% B.Less than 100% C.200% D.None of the above

Last Answer : A.Greater then 100%

Uniformity measure of a planter is a) Equal seed spacing b) Equal number of seed dropped per hill c) Minimum variation in different openers d) All of the above Ans. d

Description : Uniformity measure of a planter is a) Equal seed spacing b) Equal number of seed dropped per hill c) Minimum variation in different openers d) All of the above Ans. d

Last Answer : ans d

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder

Last Answer : a.) Decreasing cylinder peripheral speed.

Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate

Last Answer : a)peripheral speed of the drum

Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above

Last Answer : M. Cylinder peripheral speed

Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50

Description : Improved uniformity is obtained if seed tube is inclined rear ward at _________ with vertical. a)5-15° b)15-30° c)30-40° d)40-50

Last Answer : b)15-30°

The metering mechanism used in potato planter is: A. Fluted roller B. Brush feed type C. Picker wheel type D. Cell feed type

Description : The metering mechanism used in potato planter is: A. Fluted roller B. Brush feed type C. Picker wheel type D. Cell feed type

Last Answer :  Picker wheel type

Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above

Description : Chain drives are stable for a) Constant speed ratio between parallel shafts b) Distance between centre to centre is moderate c) Dirty and dusty environment d) All of the above

Last Answer : d) All of the above

The mechanism which picks up seeds from the seed box and delivers them in to the seed tube is known as? [a] Seed Enhancer Mechanism [b] Seed Metering Mechanism [c] Seed Placing Mechanism [d] Seed Augmenting Mechanism [e] None of the above

Description : The mechanism which picks up seeds from the seed box and delivers them in to the seed tube is known as? [a] Seed Enhancer Mechanism [b] Seed Metering Mechanism [c] Seed Placing Mechanism [d] Seed Augmenting Mechanism [e] None of the above

Last Answer : [d] Seed Augmenting Mechanism

The mechanism of a seed drill or fertilizer distributor which delivers seeds or fertilizers from the hopper at selected rates is called . a) Seed drill b) Seed box c) Seed metering mechanism d) Covering device

Description : The mechanism of a seed drill or fertilizer distributor which delivers seeds or fertilizers from the hopper at selected rates is called . a) Seed drill b) Seed box c) Seed metering mechanism d) Covering device

Last Answer : Seed metering mechanism  

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100

Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Description : Application rate of sprayer is affected by a. forward of speed b. number of nozzle c. rate of discharge d. all of the above

Last Answer : d. all of the above

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above

Last Answer : b) Decrease in the kinetic angle of repose

.total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above

raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement

Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement

Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

Nozzle spacing on boom is governed by a.) Type of spray b.) Height of crops c.) Density of crop d.) All of the above

Description : Nozzle spacing on boom is governed by a.) Type of spray b.) Height of crops c.) Density of crop d.) All of the above

Last Answer : d.) All of the above

The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Description : The mechanical cleaning of sugar cane is done due to A. The different in the peripheral velocity of rollers B. Rough surface provided Or the outer surface of rollers C. Blow of air which forces the extraneous material out of the machine D. All of the above

Last Answer : D. All of the above

A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660

Last Answer : a. 11

_______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Description : _______ designates the shape of gross peripheral and cross-sectional boundaries of the soil working tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Last Answer : c) Edge shape

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k

Last Answer : B. 28.8 x 10-2k

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Last Answer : b) 28.8 * 10-2k

Cell fill is affected by (a) Seed size (b) Cell speed (c) Cell size (d) All of the above

Description : Cell fill is affected by (a) Seed size (b) Cell speed (c) Cell size (d) All of the above

Last Answer : d) All of the above

Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above

Last Answer : (a) Increase threshing efficiency

Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above

Last Answer : d) All of the above

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm