Stress under suddenly applied load is (a) Three times than the gradually applied load (b) equal to the that due to gradually applied load (c) Less than that due to gradually applied load (d) none

Stress under suddenly applied load is
(a) Three times than the gradually applied load
(b) equal to the that due to gradually applied load
(c) Less than that due to gradually applied load
(d) none
by

1 Answer

Answer :

(d) none
by

Related questions

In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.

Description : In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.

Last Answer : c.with an impact.

The maximum stress intensity due to a suddenly applied load is x-times the stress intensity produced by the load of the same magnitude applied gradually. The value of x is (A) 1 (B) 2 (C) 3 (D) 1/2

Description : The maximum stress intensity due to a suddenly applied load is x-times the stress intensity produced by the load of the same magnitude applied gradually. The value of x is (A) 1 (B) 2 (C) 3 (D) 1/2

Last Answer : (B) 2

The ratio of the stresses produced by a suddenly applied load and by a gradually applied load on a bar, is (A) 1/4 (B) 1/2 (C) 1 (D) 2

Description : The ratio of the stresses produced by a suddenly applied load and by a gradually applied load on a  bar, is  (A) 1/4  (B) 1/2  (C) 1  (D) 2 

Last Answer : (D) 2 

Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed

Last Answer : b) 468.6N/mm²

The range within which a load can be applied on a rectangular column, to avoid any tensile stress,is (a) One-half of the base (b) One-fifth of the base (c) One-fourth of the base (d) One-fifth of the base

Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress,is (a) One-half of the base (b) One-fifth of the base (c) One-fourth of the base (d) One-fifth of the base

Last Answer : (b) One-fifth of the base

For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Last Answer : (c) d/4

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (a) One-half of the radius (b) One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Last Answer : (c) One-quarter of the radius

Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Last Answer : c. Zero at centre to maximum at circumference.

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct

Last Answer : d. Both A and B is correct

Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none

Last Answer : (b) Bending effect

Real stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Description : Real stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Last Answer : b) Changing area of cross section

Unit stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Description : Unit stress after load application is based on (a) Original area of cross section (b) Changing area of cross section (c) Final area of cross section under maximum load (d) None

Last Answer : (a) Original area of cross section

Breaking stress is (a) greater than the ultimate stress (b) Less than the ultimate stress (c) equal to the ultimate stress (d) None

Description : Breaking stress is (a) greater than the ultimate stress (b) Less than the ultimate stress (c) equal to the ultimate stress (d) None

Last Answer : (a) greater than the ultimate stress

A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Last Answer : (a) 2.87Mpa

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

For long columns, the value of buckling load is……………..crushing load. (a) Less than (b) More than (c) Equal to (d) None of these

Description : For long columns, the value of buckling load is……………..crushing load. (a) Less than (b) More than (c) Equal to (d) None of these

Last Answer : (a) Less than

In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression spring should be a. lees than natural frequency of vibration b. twenty times the natural frequency of vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Description : In a square and ground helical spring the effective number of turns is incresead by a. 1 b. 2 c. 1.5 d. 0 Ans: b 77. Frequency of the fluctuating load of helical compression ... vibration c. slightly greater than the natural frequency d. twenty times less than the natural frequency of vibration

Last Answer : d. twenty times less than the natural frequency of vibration

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Description : A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Last Answer : (b) Y-Y axis

A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Description : A shaft is said to be in pure torsion if a. Turning moment is applied at one end and other end is free b. Turning force is applied at one end and other end is free c. Two opposite turning moments are applied to the shaft d. Combination of torsional load and bending load is applied to the shaft

Last Answer : c. Two opposite turning moments are applied to the shaft

According to Euler’s column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends. (a) equal to (b) two times (c) four times (d) eight times

Description : According to Euler’s column theory, the crippling load for a column of length (l) fixed at both ends is __________ the crippling load for a similar column hinged at both ends. (a) equal to (b) two times (c) four times (d) eight times

Last Answer : (c) four times

With identical beam and column, buckling occurs as compared to bending under a (a) Lesser load (b) Larger load (c) Equal load (d) None

Description : With identical beam and column, buckling occurs as compared to bending under a (a) Lesser load (b) Larger load (c) Equal load (d) None

Last Answer : (a) Lesser load

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Last Answer : (d) direct and bending stress both

When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Description : When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Last Answer : (b) Bottom fibre

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram

Last Answer : (d) Trust diagram

Rapture stress is (a) Breaking stress (b) Load at the braking point/A (c) Load at the breaking point/Neck area (d) Maximum Stress

Description : Rapture stress is (a) Breaking stress (b) Load at the braking point/A (c) Load at the breaking point/Neck area (d) Maximum Stress

Last Answer : (c) Load at the breaking point/Neck area

Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None

Description : Linear stress strain curve is for a (a) Load ∞ displacement (b) Load ∞ ( 1/displacement) (c) Load = ( displacement)2 (d) None

Last Answer : (a) Load ∞ displacement

The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Description : The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Last Answer : (c) Yield point

Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Description : Design of a thin shell under pressure is done on the basis of a. Radial stress b. Longitudinal stress c. Hoop stress d. All the three stresses

Last Answer : c. Hoop stress

Deflection due to shear force as compared to bending moment will be a.equal b.less c.More d.None.

Description : Deflection due to shear force as compared to bending moment will be a.equal b.less c.More d.None.

Last Answer : b.less

Actual stress in the bolts of a flanged coupling of a shaft will be (a) More than the designed strength (b) Less than the designed strength (c) Neither more nor less than the designed strength (d) None

Description : Actual stress in the bolts of a flanged coupling of a shaft will be (a) More than the designed strength (b) Less than the designed strength (c) Neither more nor less than the designed strength (d) None

Last Answer : (b) Less than the designed strength

A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Description : A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile  load W. The strain energy stored in the bar is  (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Last Answer : (D) W²L/2AE

The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid(C) The flow of fluid through the pipe is suddenly brought to rest by closing of the valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Description : The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid (C) The flow of fluid through the pipe is suddenly brought to ... valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Last Answer : Answer: Option C

Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Last Answer : d. Is ability to resist maximum twisting moment

When a section is subjected to two equal and opposite forces tangentially to the section, the stress produced is known as (a) Tensile stress (b) Lateral stress (c) Shear stress (d) No stress

Description : When a section is subjected to two equal and opposite forces tangentially to the section, the stress produced is known as (a) Tensile stress (b) Lateral stress (c) Shear stress (d) No stress

Last Answer : (c) Shear stress

The direct stress included in a long column is………….. as compared to bending stress. (a) More (b) Less (c) Same (d) Negligible

Description : The direct stress included in a long column is………….. as compared to bending stress. (a) More (b) Less (c) Same (d) Negligible

Last Answer : d) Negligible

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

A column that fails due to direct stress is called (a) Short column (b) Long column (c) Medium column (d) Slender column

Description : A column that fails due to direct stress is called (a) Short column (b) Long column (c) Medium column (d) Slender column

Last Answer : (a) Short column

The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Description : The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Last Answer : a. 0.75

A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

Which of the machine component is designed under bending stress? a. Shaft b. Arm of a lever c. Key d. Belts and ropes

Description : Which of the machine component is designed under bending stress? a. Shaft b. Arm of a lever c. Key d. Belts and ropes

Last Answer : b. Arm of a lever

Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Description : Two concentric springs with stiffness equal to 100 N/mm and 80 N/mm respectively, when subjected to load of 900N will deflect by a. 9mm b. 11.25 mm c. 5mm d. 31.5 mm

Last Answer : c. 5mm

In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Description : In comparison with a simply supported beam of same span and load , a continuous beam has a.less maximum bending moment b. same bending moment c. higher maximum bending moment d. twice the bending moment

Last Answer : a.less maximum bending moment