The ratio of the stresses produced by a suddenly applied load and by a gradually applied load on a bar, is (A) 1/4 (B) 1/2 (C) 1 (D) 2

The ratio of the stresses produced by a suddenly applied load and by a gradually applied load on a 

bar, is 

(A) 1/4 

(B) 1/2 

(C) 1 

(D) 2 

by

1 Answer

Answer :

(D) 2 

by

Related questions

The maximum stress intensity due to a suddenly applied load is x-times the stress intensity produced by the load of the same magnitude applied gradually. The value of x is (A) 1 (B) 2 (C) 3 (D) 1/2

Description : The maximum stress intensity due to a suddenly applied load is x-times the stress intensity produced by the load of the same magnitude applied gradually. The value of x is (A) 1 (B) 2 (C) 3 (D) 1/2

Last Answer : (B) 2

A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile load W. The strain energy stored in the bar is (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Description : A bar L metre long and having its area of cross-section A, is subjected to a gradually applied tensile  load W. The strain energy stored in the bar is  (A) WL/2AE (B) WL/AE (C) W²L/AE (D) W²L/2AE

Last Answer : (D) W²L/2AE

In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.

Description : In the strain energy method of slope and deflection ,load is applied a. gradually b.suddenly c.with an impact. d.None.

Last Answer : c.with an impact.

Stress under suddenly applied load is (a) Three times than the gradually applied load (b) equal to the that due to gradually applied load (c) Less than that due to gradually applied load (d) none

Description : Stress under suddenly applied load is (a) Three times than the gradually applied load (b) equal to the that due to gradually applied load (c) Less than that due to gradually applied load (d) none

Last Answer : (d) none

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid(C) The flow of fluid through the pipe is suddenly brought to rest by closing of the valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Description : The hammer blow in pipes occurs when (A) There is excessive leakage in the pipe (B) The pipe bursts under high pressure of fluid (C) The flow of fluid through the pipe is suddenly brought to ... valve (D) The flow of fluid through the pipe is gradually brought to rest by closing of the valve

Last Answer : Answer: Option C

The ratio of average values of shear stresses produced on the bed and the banks of a channel due to flowing water is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Equal to zero

Description : The ratio of average values of shear stresses produced on the bed and the banks of a channel due to flowing water is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Equal to zero

Last Answer : Answer: Option C

Gradually applied static loads do not change with time their (A) Magnitude (B) Direction (C) Point of application (D) All the above

Description : Gradually applied static loads do not change with time their  (A) Magnitude  (B) Direction  (C) Point of application  (D) All the above

Last Answer : (D) All the above

Have you always grown up gradually, changing a little at a time, or have there been points in your life when you've changed suddenly?

Description : Have you always grown up gradually, changing a little at a time, or have there been points in your life when you've changed suddenly?

Last Answer : answer:Wow: my vote for best question of the month. I don't know how much I want to share in an open forum - but regardless of the intimacy of my, or others' posts here - it certainly was ... , probably unnecessarily but I can't help it. Fortunately, it's never too late to have a happy childhood.

A storm is predicted if atmospheric pressure – (1) Rises suddenly (2) Rises gradually (3) Falls suddenly (4) Falls gradually

Description : A storm is predicted if atmospheric pressure – (1) Rises suddenly (2) Rises gradually (3) Falls suddenly (4) Falls gradually

Last Answer : (3) Falls suddenly Explanation: Atmospheric pressure is basically the weight of air in the atmosphere above the reservoir, so the level of mercury continues to change until the weight of mercury in the ... reduces the weight of air above the reservoir so the mercury level drops to a lower level.

A storm is predicted if atmospheric pressure (1) rises suddenly (2) rises gradually (3) falls suddenly (4) falls gradually

Description : A storm is predicted if atmospheric pressure (1) rises suddenly (2) rises gradually (3) falls suddenly (4) falls gradually

Last Answer :  falls suddenly

In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

If all the dimensions of a bar are increased in the proportion n : 1, the proportion with which the maximum stress produced in the prismatic bar by its own weight, will increase in the ratio (A) 1 : n (B) n : 1 (C) 1 : (1/n) (D) 1 : n

Description : If all the dimensions of a bar are increased in the proportion n : 1, the proportion with which the maximum stress produced in the prismatic bar by its own weight, will increase in the ratio (A) 1 : n (B) n : 1 (C) 1 : (1/n) (D) 1 : n

Last Answer : (B) n : 1

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends

Description : A pressure conduit laid underground, may not be subjected to  (A) Internal pressure of water  (B) Pressure due to external load  (C) Longitudinal temperature stress  (D) Longitudinal stresses due to unbalanced pressure to bends 

Last Answer : (C) Longitudinal temperature stress 

Ab and Ac are the cross sections of bronze and copper bars of equal lengt b c are their respective stresses due to load P. If Pb and Pc are the loads shared by them, (where Eb and Ec are their modulii). (A) b c = Eb /Ec (B) P = Pb + Pc (C) P = Ab b + Ac b (D) All the above

Description : Ab and Ac  are the cross sections of bronze and copper bars of equal lengt b c  are their  respective stresses due to load P. If Pb and Pc  are the loads shared by them, (where Eb and Ec  are  their modulii) ... /Ec (B) P = Pb + Pc (C) P = Ab b + Ac b (D) All the above 

Last Answer : (D) All the above 

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on the column, should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Last Answer : Answer: Option B

The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above

Last Answer : Answer: Option D

The critical combination of stresses for corner region in cement concrete roads is (A) Load stress + warping stress frictional stress (B) Load stress + warping stress + frictional stress (C) Load stress + warping stress (D) Load stress + frictional stress

Description : The critical combination of stresses for corner region in cement concrete roads is (A) Load stress + warping stress frictional stress (B) Load stress + warping stress + frictional stress (C) Load stress + warping stress (D) Load stress + frictional stress

Last Answer : Answer: Option C

The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Description : The transverse reinforcements provided at right angles to the main reinforcement. (a) To distribute the load. (b) To resist the temp stresses (c) To resist the shrinkage stresses (d) All the above

Last Answer : (d) All the above

The ratio of maximum and average shear stresses on a rectangular section, is (A) 1 (B) 1.25 (C) 1.5 (D) 2.5

Description : The ratio of maximum and average shear stresses on a rectangular section, is  (A) 1  (B) 1.25  (C) 1.5  (D) 2.5 

Last Answer : (C) 1.5

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %

Description : If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is (A) 0.496 % (B) 0.596 % (C) 0.696 % (D) 0.796 %

Last Answer : Answer: Option C

__________ iron is produced, when molten pig iron is allowed to cool gradually. (A) White cast (B) Grey cast (C) Wrought (D) None of these

Description : __________ iron is produced, when molten pig iron is allowed to cool gradually. (A) White cast (B) Grey cast (C) Wrought (D) None of these

Last Answer : (B) Grey cast

A simply supported beam which carries a uniformly distributed load has two equal overhangs. To have maximum B.M. produced in the beam least possible, the ratio of the length of the overhang to the total length of the beam, is (A) 0.207 (B) 0.307 (C) 0.407 (D) 0.508

Description : A simply supported beam which carries a uniformly distributed load has two equal overhangs. To  have maximum B.M. produced in the beam least possible, the ratio of the length of the overhang  to the total length of the beam, is  (A) 0.207  (B) 0.307  (C) 0.407  (D) 0.508 

Last Answer : (A) 0.207 

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (C) Gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve (D) None of these

Description : Transition curves are introduced at either end of a circular curve, to obtain (A) Gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the ... specified amount at the junction of the transition curve with main curve (D) None of these

Last Answer : (B) Gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve

direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure developed during the test (C) As the test progresses the area under shear, gradually changes (D) None of these

Description : direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure ... C) As the test progresses the area under shear, gradually changes (D) None of these

Last Answer : Answer: Option C

To ensure uniform pressure distribution, the thickness of the foundation, isA) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Description : To ensure uniform pressure distribution, the thickness of the foundation, is A) Kept uniform throughout (B) Increased gradually towards the edge (C) Decreased gradually towards the edge (D) Kept zero at the edge

Last Answer : Answer: Option C

When the flow in an open channel is gradually varied, the flow is said to be (A) Steady uniform flow (B) Steady non-uniform flow (C) Unsteady uniform flow (D) Unsteady non-uniform flow

Description : When the flow in an open channel is gradually varied, the flow is said to be (A) Steady uniform flow (B) Steady non-uniform flow (C) Unsteady uniform flow (D) Unsteady non-uniform flow

Last Answer : Answer: Option B

Gradually varied flow is (A) Steady uniform (B) Non-steady non-uniform (C) Non-steady uniform (D) Steady non-uniform

Description : Gradually varied flow is (A) Steady uniform (B) Non-steady non-uniform (C) Non-steady uniform (D) Steady non-uniform

Last Answer : Answer: Option D

The atmospheric pressure with rise in altitude decreases (A) Linearly (B) First slowly and then steeply (C) First steeply and then gradually (D) Unpredictable

Description : The atmospheric pressure with rise in altitude decreases (A) Linearly (B) First slowly and then steeply (C) First steeply and then gradually (D) Unpredictable

Last Answer : Answer: Option B

Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Description : Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Last Answer : (a) Same

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

Explain the effect of eccentric load with sketch w.r.t stresses developed

Description : Explain the effect of eccentric load with sketch w.r.t stresses developed

Last Answer : Effect of eccentric load: A load whose line of action does not coincide with the axis of a member is called an eccentric load .The distance between the eccentric axis of the body and the point of ... member. Thus the resultant stresses due to direct as well as bending stresses in the member

Stanley loved fishing and also loved boasting about how an amazing person he is. One day he went into a bar after fishing, and started telling people in the bar about something that just happened. 'So I was fishing by the waters, really nice breeze, and suddenly there was this person who creeped from behind and wanted to stab me in the stomach. Because I'm so good in Kung Fu, I turned back and WHAM! I slapped him in the face!' Everyone enjoyed the rest of the story when one person asked him: 'You're lying, Stan, are you?' How did the man knew that Stanley was lying? -Riddles

Description : Stanley loved fishing and also loved boasting about how an amazing person he is. One day he went into a bar after fishing, and started telling people in the bar about something that just happened. 'So I was ... : 'You're lying, Stan, are you?' How did the man knew that Stanley was lying? -Riddles

Last Answer : How can the man stab Stanley in the stomach if he's creeping up from BEHIND?

If the stress produced by a prismatic bar is equal to the working stress, the area of the cross￾section of the prismatic bar, becomes (A) Zero (B) Infinite (C) Maximum (D) Minimum

Description : If the stress produced by a prismatic bar is equal to the working stress, the area of the cross￾section of the prismatic bar, becomes  (A) Zero  (B) Infinite  (C) Maximum  (D) Minimum

Last Answer : (B) Infinite 

Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is an important factor for road safety and depends on the initial velocity ( v 0 ) and the braking capacity, or deceleration, ?a that is caused by the braking. A car travelling at speed 72km/hr suddenly applies the brake with the deceleration of 5m/s2. Find the stopping distance of the car -Science

Description : Stopping distance of vehicles : When brakes are applied to a moving vehicle, the distance it travels before stopping is called stopping distance. It is an important factor for road safety and depends on ... the brake with the deceleration of 5m/s2. Find the stopping distance of the car -Science

Last Answer : Here u=72 km/hr = 72×10003600m/s=2072×10003600m/s=20 m/s , v=0 a= -5 m/s2 Now using the relation v2=u2+2asv2=u2+2as 0=(20)2+2×(−5)×s0=(20)2+2×(−5)×s s=40ms=40m

What term is applied to dry stream channels with nearly vertical walls and flat bottoms which are characteristic of semi-arid regions. They may suddenly become filled with torrential waters after heavy rains. The term has a Spanish origin.

Description : What term is applied to dry stream channels with nearly vertical walls and flat bottoms which are characteristic of semi-arid regions. They may suddenly become filled with torrential waters after heavy rains. The term has a Spanish origin.

Last Answer : ANSWER: ARROYO

The deflection of a uniform circular bar of diameter d and length , which extends by an amount under a tensile pull , when it carries the same load at its mid-span, is (A) el/2d (B) e²l/3d² (C) el²/3d² (D) e²l²/3d

Description : The deflection of a uniform circular bar of diameter d and length , which extends by an  amount under a tensile pull , when it carries the same load at its mid-span, is  (A) el/2d (B) e²l/3d² (C) el²/3d² (D) e²l²/3d

Last Answer : (C) el²/3d

A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm

Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a  load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending  strain energy stored in the ... (A) 411 N mm  (B) 511 N mm  (C) 611 N mm  (D) 711 N mm 

Last Answer : (C) 611 N mm 

In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Description : In a bar of large length when held vertically and subjected to a load at its lower end, its own￾weight produces additional stress. The maximum stress will be (A) At the lower cross-section (B) At the built-in upper cross-section (C) At the central cross-section (D) At every point of the bar

Last Answer : (B) At the built-in upper cross-section

When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Last Answer : (C) Tensile stress

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

The range within which a load can be applied on a rectangular column, to avoid any tensile stress, is (A) One-half of the base (B) One-fifth of the base (C) One-fourth of the base (D) One-fifth of the base

Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress,  is  (A) One-half of the base  (B) One-fifth of the base  (C) One-fourth of the base  (D) One-fifth of the base 

Last Answer : (B) One-fifth of the base 

For keeping the stress wholly compressive the load may be applied on a circular column anywhere within a concentric circle of diameter (A) d/2 (B) d/3 (C) d/4 (D) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywhere within a concentric circle of diameter (A) d/2 (B) d/3 (C) d/4 (D) d/8

Last Answer : (C) d/4

The internal molecular attraction of a soil, the cohesion (A) Decreases as the moisture content increases (B) Increases as the moisture content decreases (C) Is more in well compacted clays (D) Depends upon the external applied load

Description : The internal molecular attraction of a soil, the cohesion (A) Decreases as the moisture content increases (B) Increases as the moisture content decreases (C) Is more in well compacted clays (D) Depends upon the external applied load

Last Answer : Answer: Option C

Terzaghi's theory of one dimensional consolidation assumes (A) Load is applied in one direction (B) Coefficient of permeability is constant (C) Excess pore water drains out only in the vertical direction (D) All the above

Description : Terzaghi's theory of one dimensional consolidation assumes (A) Load is applied in one direction (B) Coefficient of permeability is constant (C) Excess pore water drains out only in the vertical direction (D) All the above

Last Answer : Answer: Option D

When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Last Answer : Answer: Option C

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2