Description : Relation between shear force and Concentrated load is (a) dV/dx= 0 (b) dV/dx=– W (c) dV/dx=–W (d) None
Last Answer : (a) dV/dx= 0
Description : Relation between shear force and UDL is (a) dV/dx=+ w (b) dV/dx=– w (c) dV/dx=± w (d) None
Last Answer : (b) dV/dx=– w
Description : The relation between bending moment and concentrated load is (a) dM/dx=0 (b) dM/dx= –Vx (c) dM/dx= Vx (d) None
Last Answer : (c) dM/dx= Vx
Description : In a cantilever subjected to a combination of concentrated load, uniformly distributed load and uniformly varying load, Maximum bending moment is (a) Where shear force=0 (b) At the free end (c) At the fixed end (d) At the mid-point
Last Answer : (c) At the fixed end
Description : Relation between bending moment and shear force is (a) dM/dx = -Vx (b) dM/dx = ±Vx (c) dM/dx = Vx (d) None
Last Answer : (c) dM/dx = Vx
Description : 7-For any part of the beam, between two concentrated load Shear force diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola
Last Answer : Na
Description : n case of a cantilever beam having concentrated loads, shear force variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : (d) None
Description : In case of a cantilever beam having concentrated loads, shear force variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : d) None
Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero
Last Answer : (d) Zero
Description : In a cantilever subjected to a concentrated load (W) at the free end and having length =l, Maximum bending moment is (a) Wl at the free end (b) Wl at the fixed end (c) Wl/2 at the fixed end (d) Wl at the free end
Last Answer : (b) Wl at the fixed end
Description : The relation between bending moment and UDL is (a) dM/dx=0 (b) dM/dx= –Vx (c) dM/dx= Vx (d) None
Last Answer : c) dM/dx= Vx
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola
Last Answer : (c) Line inclined to x-axis
Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law
Last Answer : (c) Follows a parabolic law
Description : Macaulays method is more convenient for beams carrying a. Single concentrated load. b.UDL c. Multi loads d.None.
Last Answer : c. Multi loads
Description : Maximum bending moment in a S.S. beam having a concentrated load at the centre will be (a) WL (b) WL/2 (c) WL/4 (d) None
Last Answer : (c) WL/4
Description : A concentrated load P acts on a simply supported beam of span L at a distance L/3 from the left support. The bending moment at the point of application of the load is given by (a) PL/3 (b) 2PL/3 (c) PL/9 (d) 2PL/9
Last Answer : (d) 2PL/9
Description : A sudden jump anywhere on the Bending moment diagram of a beam is caused by (a) Couple acting at that point (b) Couple acting at some other point (c) Concentrated load at the point (d) Uniformly distributed load or Uniformly varying load on the beam
Last Answer : (a) Couple acting at that point
Description : For any part of a beam between two concentrated load, Bending moment diagram is a (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola
Description : In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero
Last Answer : (a) Is always zero if it does not carry couple at the end
Description : Point of contra-flexure is a (a) Point where Shear force is maximum (b) Point where Bending moment is maximum (c) Point where Bending moment is zero (d) Point where Bending moment=0 but also changes sign from positive to negative
Last Answer : (d) Point where Bending moment=0 but also changes sign from positive to negative
Description : At a point in a simply supported or overhanging beam where Shear force changes sign and = 0, Bending moment is (a) Maximum (b) Zero (c) Either increasing or decreasing (d) Infinity
Last Answer : (a) Maximum
Description : Wahl’s stress concentration factor is used in close coiled springs under axial load to account for (a) Shear effect (b) Bending effect (c) Compression effect (d) none
Last Answer : (b) Bending effect
Description : A closed helical spring under axial load is designed on the basis of (a) Shear (b) Compression (c) Bending (d) None
Last Answer : (a) Shear
Description : When two helical springs of equal lengths are arranged to form a cluster spring, then a. Shear stress in each spring will be equal b. Load taken by each spring will be half the total load c. Only A is correct d. Both A and B is correct
Last Answer : d. Both A and B is correct
Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed
Last Answer : b) 468.6N/mm²
Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None
Last Answer : (b) Shear stresses
Description : When a close-coiled helical spring is subjected to an axial load, it is said to be under. (a) Bending (b) Shear (c) Torsion (d) Crushing
Last Answer : (c) Torsion
Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both
Last Answer : (d) direct and bending stress both
Description : When sinking is accounted in a continuous beam the shear force is a.modified b.same c.zero d.infinite
Last Answer : a.modified
Description : A beam is designed on the basis of a. Maximum bending moment b. Minimum shear force. c.Maximum bending moment as well as for maximum shear force d. None.
Last Answer : c.Maximum bending moment as well as for maximum shear force
Description : Deflection due to shear force as compared to bending moment will be a.equal b.less c.More d.None.
Last Answer : b.less
Description : The design of a beam is based on strength criteria, if the beam is sufficiently strong to resist ----------------. a.Shear force b.deflection c. both a and b. d. none of the above.
Last Answer : a.Shear force
Description : A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange
Last Answer : c. neutral axis of the section
Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2
Last Answer : b. 281.25 mm2
Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm
Last Answer : c. 142.72 mm
Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data
Last Answer : c. 8.88 N/mm2
Description : Shear force in a beam is (a) Parallel to the length (b) Perpendicular to the length (c) Neither parallel nor perpendicular to the length (d) None
Last Answer : (b) Perpendicular to the length
Description : In case of a cantilever beam, shear force at the fixed end will be (a) Maximum (b) Minimum (c) Zero (d) None
Description : The slope of shear force line at any section of the beam is also called (a) Bending moment at that section (b) Rate of loading at that section (c) Maximum Shear force (d) Maximum bending moment
Last Answer : (b) Rate of loading at that section
Description : Point of contra-flexure is also called (a) Point of maximum Shear force (b) Point of maximum Bending moment (c) Point of inflexion (d) Fixed end
Last Answer : (c) Point of inflexion
Description : A sudden increase or decrease in shear force diagram between any two points indicates that there is (a) No loading between the two points (b) Point loads between the two points (c) U.D.L. between the two points (d) None of these
Last Answer : (b) Point loads between the two points
Description : The rate of change of bending moment is equal to (a) Shear force (b) Slope (c) Deflection (d) None of these
Last Answer : (a) Shear force
Description : A cantilever beam of length of 2m carries a U.D.L. of 150 N/m over its whole span. The maximum shear force in the beam will be (a) 150 N (b) 300 N (c) 150 N-m (d) 600 N-m
Last Answer : (b) 300 N
Description : In prestressed concrete members, the shear force depends upon (a) Distributed load (b) Torsion (c) Concentrated load (d) Variation in net bending moment
Last Answer : (d) Variation in net bending moment
Description : Shear deflection of a cantilever of length L, cross sectional area A and shear modulus G, under a concentrated load W at its free end, is (A) (2/3) (WL/AG) (B) (1/3) (WL²/EIA) (C) (3/2) (WL/AG) (D) (3/2) (WL²/AG
Last Answer : (C) (3/2) (WL/AG
Description : The length of a wire is increased by 1 mm on the application of a certain load. In a wire of the same material but of twice the length and half the radius, the same force will produce an elongation of (a) 0.5 mm (b) 2 mm (c) 4 mm (d) 8 mm
Last Answer : (d) 8 mm
Description : Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these
Last Answer : Answer: Option C
Description : In case of a cantilever beam having concentrated loads, bending moment variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : (a) Linear
Description : Variation of bending moment due to concentrated loads will be (a) Linear (b) Parabolic (c) Cubic (d) None