Maximum shear stress of a solid shaft is given by a. 16T/πd b. 16T/πd2 c. 16T/πd3 d. 16T/πd4

Maximum shear stress of a solid shaft is given by  
a. 16T/πd
b. 16T/πd2
c. 16T/πd3
d. 16T/πd4
by

1 Answer

Answer :

c. 16T/πd3
by

Related questions

The polar moment of inertia of a solid circular shaft of diameter (d) is (a)πd2/16 (b) πd3/32 (c) πd4/32 (d) πd4/64

Description : The polar moment of inertia of a solid circular shaft of diameter (d) is (a)πd2/16 (b) πd3/32 (c) πd4/32 (d) πd4/64

Last Answer : (c) πd4/32

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow shaft maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius

Last Answer : b. In a solid shaft maximum shear stress occurs at center

A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced in the shaft, is (A) Zero (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Description : A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced  in the shaft, is  (A) Zero  (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Last Answer : (B) 16T/ 3

A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength

Last Answer : (a) maximum normal stress theory

A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p

Last Answer : (d) 27/p

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment

Last Answer : d. Is ability to resist maximum twisting moment

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T

Last Answer : d. 2M/T

Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Last Answer : c. Zero at centre to maximum at circumference.

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

Variation of shear stress in a shaft is (a) Parabolic (b) Linear (c) Cubical (d) None

Description : Variation of shear stress in a shaft is (a) Parabolic (b) Linear (c) Cubical (d) None

Last Answer : b) Linear

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Description : The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these

Last Answer : (a) Uniform rate

The shear stress is minimum at (a) Axis of the shaft (b) Outer surface of the shaft (c) Anywhere inside the shaft (d) None of these

Description : The shear stress is minimum at (a) Axis of the shaft (b) Outer surface of the shaft (c) Anywhere inside the shaft (d) None of these

Last Answer : (c) Anywhere inside the shaft

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : b. Angle of twist

For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.

Last Answer : c. torque

The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Description : The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform

Last Answer : a. Linear

For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these

Description : For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these

Last Answer : (a) t = Tr/J

Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above

Description : Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above

Last Answer : a. is zero

For the same material, length and given torque, a hollow shaft weighs……………… a solid shaft. (a) Less than (b) More than (c) Equal to (d) None of these

Description : For the same material, length and given torque, a hollow shaft weighs……………… a solid shaft. (a) Less than (b) More than (c) Equal to (d) None of these

Last Answer : (a) Less than

For the same material, length and given torque a hoolow shaft weighs ---------- a solid shaft. a. less than b. more than. c. equal to d. not equal to.

Description : For the same material, length and given torque a hoolow shaft weighs ---------- a solid shaft. a. less than b. more than. c. equal to d. not equal to.

Last Answer : a. less than

Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Description : Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Last Answer : b) (σh+ σr)/2

Considering σh, σl and σr, maximum shear stress will be a) (σh—σl) /2 b) (σl— σh) /2 c) (σh + σr) /2 d) None

Description : Considering σh, σl and σr, maximum shear stress will be a) (σh—σl) /2 b) (σl— σh) /2 c) (σh + σr) /2 d) None

Last Answer : c) (σh + σr) /2

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa

Last Answer : (a) 2.87Mpa

Shear stress in a I-section beam is maximum art the (a) Outermost fiber (b) At the junction of web and flange (c) Central fiber (d) None

Description : Shear stress in a I-section beam is maximum art the (a) Outermost fiber (b) At the junction of web and flange (c) Central fiber (d) None

Last Answer : b) At the junction of web and flange

Shear stress is maximum at the (a) Outermost fiber (b) Central fiber (c) Neither outermost nor central fiber (d) None

Description : Shear stress is maximum at the (a) Outermost fiber (b) Central fiber (c) Neither outermost nor central fiber (d) None

Last Answer : (b) Central fiber

The shear stress acting on the neutral axis of a beam is _____ a. maximum b. minimum c. zero d. none of the above

Description : The shear stress acting on the neutral axis of a beam is _____ a. maximum b. minimum c. zero d. none of the above

Last Answer : a. maximum

Maximum shear stress in a triangular section ABC of height H and base B occurs at _________ a. H b. H/2 c. H/3 d. neutral axis

Description : Maximum shear stress in a triangular section ABC of height H and base B occurs at _________ a. H b. H/2 c. H/3 d. neutral axis

Last Answer : b. H/2

The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Description : The average shear stress in a beam of circular section is _______ times the maximum shear stress. a. 0.75 b. 1.5 c. 4/3 d. equa

Last Answer : a. 0.75

A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2

Last Answer : b. 281.25 mm2

A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Description : A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa? a. 27.311 mm b. 75.56 mm c. 142.72 mm d. 692.10 mm

Last Answer : c. 142.72 mm

The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above

Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above

Last Answer : a. circular cross-section

What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2

Description : What is the average shear stress acting on a rectangular beam, if 50 N/mm2is the maximum shear stress acting on it? a. 31.5 N/mm2 b. 33.33 N/mm2 c. 37.5 N/mm2 d. 42.5 N/mm2

Last Answer : b. 33.33 N/mm2

The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Description : The bending moment ‘M’ and a torque ‘T’ is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then ‘M’ is equal to (A) T/2 (B) T (C) 2 T (D) 4 T

Last Answer : (A) T/2

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Last Answer : c) 16M/πdᵌ

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ

Last Answer : b) 32M/πdᵌ

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability

Last Answer : d. Good cast ability

The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]

Description : The shear stress concentration factor (Ks) in mechanical springs is given as _____ a. (1 + 0.5 / C) b. 0.615 / C c. (1 + 0.615 / C) d. [(4C – 1) / (4C + 1)] + [0.615 / C]

Last Answer : a. (1 + 0.5 / C)