Description : For the same material, length and given torque a hoolow shaft weighs ---------- a solid shaft. a. less than b. more than. c. equal to d. not equal to.
Last Answer : a. less than
Description : A solid shaft of same cross sectional area and of same material as that of a hollow shaft can resist a. Less torque. b. More torque. c. Equal torque. d. Unequal torque.
Last Answer : a. Less torque.
Description : The strength of a hollow shaft for the same length, material and weight is ---------- a solid shaft. a. less than. b. more than. c. equal to. d. not equal to.
Last Answer : b. more than.
Description : The strength of a hollow shaft is ……… for the same length, material and weight of a solid shaft. (a) More (b) Less (c) Equal (d) None of these
Last Answer : (b) Less
Description : For same length, same material, same length a. Weight of solid shaft is less than weight of hollow shaft b. Weight of solid shaft is more than weight of hollow shaft c. Weight of hollow and solid shafts will be same d. Sometime more sometime less
Last Answer : b. Weight of solid shaft is more than weight of hollow shaft
Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft
Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft
Description : The strain energy will be higher in which shaft under the same torque (a) Solid shaft (b) Hollow shaft (c) Same in Solid as well as hollow shaft (d) None
Last Answer : (b) Hollow shaft
Description : The stiffness of solid shaft is---------- than the stiffness of hollow shaft with same weight. a) less b) more c) equal d) not equal
Last Answer : b) more
Description : The strength of hollow shaft is more than the strength of solid shaft of ---------weight. a) same b) different c) equal d) not equa
Last Answer : a) same
Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7
Last Answer : a. 15/16
Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa
Last Answer : (c) 286 Mpa
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D
Last Answer : (c) π/4fs(D4-d4)/D
Description : Solid shaft is ----------than hollow shaft of same weight. a) cheaper b) costlier c) not costlier d) not cheaper
Last Answer : b) costlier
Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same
Last Answer : d. Only torque transmitting capacity of the shaft is same
Description : From strength point of view, whether hollow or solid shaft will be preferable (a) Solid shaft (b) Hollow shaft (c) Both solid as well as hollow shaft (d) None
Last Answer : b) Hollow shaft
Description : For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these
Last Answer : (a) t = Tr/J
Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius
Last Answer : b. In a solid shaft maximum shear stress occurs at center
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa
Last Answer : (b) 82 Mpa
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : The torque transmitted by a solid shaft is (a)π/4fsd3 (b) π/16fsd3 (c) π/32fsd3 (d) π/64fsd3
Last Answer : (b) π/16fsd3
Description : The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)
Last Answer : (b) π/16(D4-d4)
Description : .In case of a hollow shaft the average torsional energy/unit volume is given by a. (τ2/4C) x (D2+d2/D2) b. (τ2/C) x (D2+d2/D2) c. (τ2/4C) x (D+d/D2) d. (τ/C) x (D2+d2/D2)
Last Answer : a. (τ2/4C) x (D2+d2/D2)
Description : A hollow circular tube with a 2.3-cm I.D. and 2.5-cm O.D. is rigidly supported at its ends. A 2.5 kN-m torque is applied at the center of this tube. What is the maximum shear stress acting on this tube? (a) 2.87Mpa (b) 4.27 Mpa (c) 6.92 Mpa (d) 10.2 Mpa
Last Answer : (a) 2.87Mpa
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.
Last Answer : c. At the outer surface of the shaft.
Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : b. Angle of twist
Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : c. torque
Description : Equivalent bending moment in a shaft subjected to axial load P, torque T and bending moment M is (a) Meq = 0.5 [M + (M2 + T2)0.5]0.5 (b) Meq = 0.5 [M + (M2 + T2)0.5] (c) Meq = ( M2 + T2)0.5 (d) None
Last Answer : (b) Meq = 0.5 [M + (M2 + T2)0.5]
Description : Equivalent torque in a shaft subjected to axial load P, torque T and bending moment M is (a) Teq = (Pa2 + M2 + T2) (b) Teq = (Pa2 + M2 + T2)0.5 (c)Teq = ( M2 + T2)0.5 (d) None
Last Answer : c)Teq = ( M2 + T2)0.5
Description : A shaft turns at 150 rpm under a torque of 1500 N-m. Power transmitted is (a) 15p kW (b) 10p kW (c) 7.5p kW (d) 5p kW (IES 1999) Hint: P = 2pNT/60
Last Answer : (c) 7.5p kW
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : A shaft a. Is always subjected to pure torsion b. Combination of M & T but no end thrust c. Combination of torque & end thrust but no bending moment d. May be subjected to a combination of M, T and end thrust
Last Answer : d. May be subjected to a combination of M, T and end thrust
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.
Last Answer : c. Zero at centre to maximum at circumference.
Description : Maximum shear stress of a solid shaft is given by a. 16T/πd b. 16T/πd2 c. 16T/πd3 d. 16T/πd4
Last Answer : c. 16T/πd3
Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16
Last Answer : d. 15/16
Description : Which of the following assumptions are made in torsion theory? a. Shaft is perfectly straight b. Material of the shaft is heterogeneous c. Twist cannot be uniform along the length of the shaft d. Shaft is perfectly curve v
Last Answer : a. Shaft is perfectly straight b. Material of the shaft is heterogeneous
Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm
Last Answer : b) 5 cm
Description : The polar moment of inertia of a solid circular shaft of diameter (d) is (a)πd2/16 (b) πd3/32 (c) πd4/32 (d) πd4/64
Last Answer : (c) πd4/32
Description : Two shafts A and B are made of the same material. The diameter of the shaft A is twice as that of shaft B. The power transmitted by the shaft A will be ........... of shaft B. (a) twice (b) four times (c) eight times (d) sixteen times
Last Answer : (c) eight times
Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False
Last Answer : a) True
Description : The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight. a) True b) False
Last Answer : b) False
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : Solid shaft is costlier than hollow shaft of same weight. a) True b) False