Description : The variation of shear stress in a circular shaft subjected to torsion is a. Linear b. Parabolic c. Hyperbolic. d. Uniform
Last Answer : a. Linear
Description : Variation of bending strain in a beam has (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None
Last Answer : (b) Linear variation
Description : Variation of bending stresses in a beam have (a) Parabolic variation (b) Linear variation (c) Cubical variation (d) None
Description : Shear stress variation is (a) Linear (b) Polynomial (c) Parabolic (d) None
Last Answer : (c) Parabolic
Description : n case of a cantilever beam having concentrated loads, shear force variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : (d) None
Description : In case of a cantilever beam having concentrated loads, shear force variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : d) None
Description : In case of a cantilever beam having UDL, bending moment variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : (b) Parabolic
Description : In case of a cantilever beam having concentrated loads, bending moment variation will be (a) Linear (b) Parabolic (c) Cubic (d) None
Last Answer : (a) Linear
Description : Variation of bending moment due to concentrated loads will be (a) Linear (b) Parabolic (c) Cubic (d) None
Description : 70. Shear strain is a (a) Linear strain (b) Parabolic strain (c) Angular strain (d) None
Last Answer : (c) Angular strain
Description : Shear strain is a (a) Linear strain (b) Parabolic strain (c) Logarithmic strain (d) None
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : A transmission shaft subjected to bending loads must be designed on the basis of (a) maximum normal stress theory (b) maximum shear stress theory (c) maximum normal stress and maximum shear stress theories (d) fatigue strength
Last Answer : (a) maximum normal stress theory
Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa
Last Answer : (c) 286 Mpa
Description : A circular shaft subjected to torsion undergoes a twist of 10in a length of 120 cm. If the maximum shear stress induced is limited to 1000 kg/cm2and if modulus of rigidity G = 0.8 x 106then the radius of the shaft should be (a) p/8 (b) p/27 (c) 18/p (d) 27/p
Last Answer : (d) 27/p
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm
Last Answer : c. 587.1 mm
Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2
Last Answer : b. 14.69 N/mm2
Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2
Last Answer : c. 20.120 N/mm2
Description : The shear stress varies from centre to the surface of the shaft with (a) Uniform rate (b) Varying rate (c) Remains same (d) None of these
Last Answer : (a) Uniform rate
Description : The shear stress is minimum at (a) Axis of the shaft (b) Outer surface of the shaft (c) Anywhere inside the shaft (d) None of these
Last Answer : (c) Anywhere inside the shaft
Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these
Last Answer : c) Shear stress
Description : Strength of a shaft a. Is equal to maximum shear stress in the shaft at the time of elastic failure b. Is equal to maximum shear stress in the shaft at the time of rupture c. Is equal to torsional rigidity d. Is ability to resist maximum twisting moment
Last Answer : d. Is ability to resist maximum twisting moment
Description : Which of the following is incorrect? a. In a solid shaft maximum shear stress occurs at radius = radius of shaft b. In a solid shaft maximum shear stress occurs at center c. In a hollow ... maximum shear stress occurs at outer radius d. In a hollow shaft minimum shear stress occurs at inner radius
Last Answer : b. In a solid shaft maximum shear stress occurs at center
Description : For two shafts joined in parallel, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : b. Angle of twist
Description : For two shafts joined in series, the --------------- in each shaft is same. a. shear stress. b. Angle of twist c. torque d. torsional stress.
Last Answer : c. torque
Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.
Last Answer : c. At the outer surface of the shaft.
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : Maximum shear stress of a solid shaft is given by a. 16T/πd b. 16T/πd2 c. 16T/πd3 d. 16T/πd4
Last Answer : c. 16T/πd3
Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.
Last Answer : c. Zero at centre to maximum at circumference.
Description : The shape of the bending moment diagram over the length of a beam, having no external load, is always (A) Linear (B) Parabolic (C) Cubical (D) Circular
Last Answer : (A) Linear
Description : The shape of the bending moment diagram over the length of a beam, carrying a uniformly distributed load is always (A) Linear (B) Parabolic (C) Cubical (D) Circular
Last Answer : (B) Parabolic
Description : The shape of the bending moment diagram over the length of a beam, carrying a uniformly increasing load, is always (A) Linear (B) Parabolic (C) Cubical (D) Circular
Last Answer : (C) Cubical
Description : In a cantilever carrying a uniformly varying load starting from zero at the free end, the shear force diagram is (a) A horizontal line parallel to x-axis (b) A line inclined to x-axis (c) Follows a parabolic law (d) Follows a cubic law
Last Answer : (c) Follows a parabolic law
Description : The distribution of shear stress in a stream of fluid in a circular tube is (A) Linear with radius for turbulent flow only (B) Linear with radius for laminar flow only (C) Linear with radius for both laminar & turbulent flow (D) Parabolic with radius for both laminar & turbulent flow
Last Answer : (C) Linear with radius for both laminar & turbulent flow
Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None
Last Answer : (c) Shear considerations only
Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting
Last Answer : b) Tensile
Description : Which property is not required for shaft materials? a. High shear and tensile strength b. Good mach inability c. High fatigue strength d. Good cast ability
Last Answer : d. Good cast ability
Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa
Last Answer : (b) 82 Mpa
Description : Actual stress in the bolts of a flanged coupling of a shaft will be (a) More than the designed strength (b) Less than the designed strength (c) Neither more nor less than the designed strength (d) None
Last Answer : (b) Less than the designed strength
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : c) 16M/πdᵌ
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdᵌ c) 16M/πdᵌ d) 8M/πdᵌ
Last Answer : b) 32M/πdᵌ
Description : For a solid or a hollow shaft subject to a twisting moment T, the torsional shearing stress t at a distance r from the centre will be (a) t = Tr/J (b) t = Tr (c) t = TJ/r (d) none of these
Last Answer : (a) t = Tr/J
Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2
Last Answer : c. 50.57 N/mm2
Description : Stress in the cross section of a shaft at the centre ________ a. is zero b. decreases linearly to the maximum value of at outer surface c. both a. and b. d. none of the above
Last Answer : a. is zero
Description : The criteria for the design of a shaft is the stress at (a) The external surface (b) The axis (c) Any inside layer (d) Any of these
Last Answer : (a) The external surface
Description : Which of the machine component is designed under bending stress? a. Shaft b. Arm of a lever c. Key d. Belts and ropes
Last Answer : b. Arm of a lever
Description : Wahl suggested the correction in the stress factor to account for a. the additional transverse shear stress b. stress concentration c. fatigue stress d. axial stress
Last Answer : b. stress concentration
Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive
Last Answer : c. torsional shear