Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Cylinder having inner diameter to wall thickness ratio less than 15 are
a) Thin cylinders
b) Thick Cylinders
c) Moderate cylinders
d) none of the above
by

1 Answer

Answer :

b) Thick Cylinders
by

Related questions

In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Description : In a thick-cylinder pressurized from inside, the hoop stress is maximum at a) The center of the wall thickness b) the outer radius c) the inner radius d) both the inner and the outer radii

Last Answer : c) the inner radius

In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum at the inner surface and minimum at the outer surface c) maximum at the inner surface and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Description : In a thick cylindrical shell subjected to an internal pressure (p), the radial stress across the thickness of a cylinder is a) maximum at the outer surface and minimum at the inner surface b) maximum ... and zero at the outer surface d) maximum at the outer surface and zero at the inner surface

Last Answer : c) maximum at the inner surface and zero at the outer surface

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Description : A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Last Answer : (D) 1/10

A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under pi and po will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under internal fluid pressure’ pi will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Description : A thick cylinder under external fluid pressure’ p0′ will have maximum stress at the 1. Outer radius 2. Inner radius 3. Mean radius 4. None

Last Answer : 2. Inner radius

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these

Last Answer : (c) outer surface of shaft

Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Description : Hoop shrinking in thick cylinders is done to achieve (a) Increased stresses (b) Decreased stresses (c ) Uniform stresses (d) None

Last Answer : Hoop shrinking technique is used to make the stresses on the cylinder walls evenly distributed around the circumference of the cylinder, which results in a uniform stress distribution. This is important for ... under load. It also makes sure that the cylinder can withstand the pressure inside it.

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Description : What is the ratio of hoop stresses in a spherical vs cylindrical shell of same diameter, thickness and under same pressure? a. 4:1 b. 2:1 c. 1:2 d. 1:4

Last Answer : c. 1:2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Description : A water main 1 m in diameter contains a fluid having pressure 1 N/mm2. If the maximum permissible tensile stress in the metal is 20 N/mm2, th thickness of the metal required would be a) 2 cm b) 2.5cm c) 1 cm d) 0.5 cm

Last Answer : b) 2.5cm

A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.

Last Answer : c) 210 MPa

The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Description : The maximum strain in a thick cylinder under pi will be a) σh/E+μ σl/E b) σh/ E+ μσr/E c) σr/E+μ σl/E d) None

Last Answer : b) σh/ E+ μσr/E

Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Description : Lame’s equation used to find the thickness of the cylinder is based on maximum strain failure. a) True b) False

Last Answer : b) False

Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Description : Lame's theory is associated with a) thick cylindrical shells b) thin cylindrical shells c) direct and bending stresses d) none of these

Last Answer : a) thick cylindrical shells

Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Description : Maximum shear stress in a hollow shaft subjected to a torsional moment is at the a. Middle of thickness. b. At the inner surface of the shaft. c. At the outer surface of the shaft. d. At the middle surface of the shaft.

Last Answer : c. At the outer surface of the shaft.

The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Description : The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside diameter D/2, in torsion, is a.1/4 b. 1/2 c. 1/16 d. 15/16

Last Answer : d. 15/16

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

Arithmetic mean area can be used in heat transfer problem to calculate the heat flow by conduction through a cylinder which is (A) Thin walled having the value of Ao Ai /< 2 (B) Thick walled (C) Having the value of Ao /Ai > 2 (D) Both (B) and (C)

Description : Arithmetic mean area can be used in heat transfer problem to calculate the heat flow by conduction through a cylinder which is (A) Thin walled having the value of Ao Ai /< 2 (B) Thick walled (C) Having the value of Ao /Ai > 2 (D) Both (B) and (C)

Last Answer : (A) Thin walled having the value of Ao Ai /< 2

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Description : The polar moment of inertia of a hollow shaft of outer diameter (D) and inner diameter (d) is given by. (a)π/16(D3-d3) (b) π/16(D4-d4) (c) π/16(D4-d4) (d) π/16(D4-d4/d)

Last Answer : (b) π/16(D4-d4)

When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an increase in diameter and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Description : When a thin cylindrical shell is subjected to an internal pressure, there will be a) a decrease in diameter and length of the shell b) an increase in diameter and length of the shell c) an ... and decrease in length of the shell d) a decrease in diameter and increase in length of the shell

Last Answer : b) an increase in diameter and length of the shell

Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its(A) Inner diameter(B) Outer diameter(C) Thickness(D) Neither inner nor outer diameter

Description : Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its (A) Inner diameter (B) Outer diameter (C) Thickness (D) Neither inner nor outer diameter

Last Answer : (D) Neither inner nor outer diameter

Consider a disk queue with I/O requests on the following cylinders in their arriving order: 6,10,12,54,97,73,128,15,44,110,34,45 The disk head is assumed to be at cylinder 23 and moving in the direction of decreasing number of cylinders. Total number of cylinders in the disk is 150. The disk head movement using SCAN-scheduling algorithm is: (1) 172 (2) 173 (3) 227 (4) 228

Description : Consider a disk queue with I/O requests on the following cylinders in their arriving order: 6,10,12,54,97,73,128,15,44,110,34,45 The disk head is assumed to be at cylinder 23 and moving in the direction ... . The disk head movement using SCAN-scheduling algorithm is: (1) 172 (2) 173 (3) 227 (4) 228

Last Answer : (2) 173

Muff coupling is designed as a ......... A. Thick cylinder B. Thin cylinder C. Solid shaft D. Hollow shaft

Description : Muff coupling is designed as a ......... A. Thick cylinder B. Thin cylinder C. Solid shaft D. Hollow shaft

Last Answer : D. Hollow shaft

Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined

Last Answer : (b) No it is flexible

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Description : Compute the maximum shearing stress developed in a phosphor bronze spring having mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. and G = 42 GPa. a. 51 MPa b. 31.89 MPa c. 80 MPa d. 70 MPa

Last Answer : b. 31.89 MPa

A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number of active coils is 10. If the mean coil diameter is reduced to 10 mm, the stiffness of the spring is approximately a. increased by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Description : A compression spring is made of music wire of 2 mm diameter having a shear strength and shear modulus of 800 Mpa and 80 Gpa respectively. The mean coil diameter is 20mm, free length is 40 mm, and the number ... by 8 times b. decreased by 2 times c. increased by 2 times d. decreased by 8 times

Last Answer : a. increased by 8 times

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Description : The thick shell is made from laminations to get (a) Increased stresses (b) Decreased stresses (c) Uniform stresses (d) None

Last Answer : (c) Uniform stresses

Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Description : Which stress is constant in a thick shell a) σh b) σl c) σr d) None

Last Answer : b) σl

Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Description : Maximum shear stress in a thick shell is a) (σh+ σl)/2 b) (σh+ σr)/2 c) (σh– σl)/2 d) None

Last Answer : b) (σh+ σr)/2

In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Description : In a thick shell which stress is negligible a) σh b) σl c) σr d) None

Last Answer : b) σl

Minimum thickness of wall where single Flemish bond can be used is (A) Half brick thick (B) One brick thick (C) One and a half bricks thick (D) Two bricks thick

Description : Minimum thickness of wall where single Flemish bond can be used is (A) Half brick thick (B) One brick thick (C) One and a half bricks thick (D) Two bricks thick

Last Answer : Answer: Option C

A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Last Answer : (B) Inner diameter