A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

A cylinder is said to be thin if the ratio of its thickness and diameter, is less than
(A) 1/25
(B) 1/20
(C) 1/15
(D) 1/10
by

1 Answer

Answer :

(D) 1/10
by

Related questions

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

In rapid sand filters the ratio of length and diameter of the lateral, should not be greater than (A) 10 (B) 15 (C) 20 (D) 25

Description : In rapid sand filters the ratio of length and diameter of the lateral, should not be greater than (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : (C) 20

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

Minimum thickness of the base of a flexible pavement, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : Minimum thickness of the base of a flexible pavement, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option A

The maximum thickness of concrete floor of a cement warehouse, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : The maximum thickness of concrete floor of a cement warehouse, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : (D) 25 cm

The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option C

A film is said to be thin if its thickness is (a) Much smaller than wavelength of light (b) Comparable with one wavelength of light (c) Of the order of nanometer (10-9 m) (d) Of the order of Pico meter (10-12 m)

Description : A film is said to be thin if its thickness is (a) Much smaller than wavelength of light (b) Comparable with one wavelength of light (c) Of the order of nanometer (10-9 m) (d) Of the order of Pico meter (10-12 m)

Last Answer : (b) Comparable with one wavelength of light

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Last Answer : (A) Zero

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 m

Description : The minimum cover in a slab should neither be less than the diameter of bar nor less than (A) 10 mm (B) 15 mm (C) 25 mm (D) 13 mm

Last Answer : Answer: Option B

Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Description : Stresses in a thin cylindrical shell under internal pressure is independent of a. Diameter b. Thickness c. Length d. Diameter and thickness

Last Answer : c. Length

Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Description : Among the cylindrical and spherical thin vessels of same material, diameter and pressure which has the lesser thickness a. Cylindrical shell b. Spherical shell c. Cylindrical shell with semi spherical heads d. None

Last Answer : b. Spherical shell

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Last Answer : (D) 1/8

The nominal thickness of an expansion joint in brick walls, is kept more than (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm

Description : The nominal thickness of an expansion joint in brick walls, is kept more than (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm

Last Answer : Answer: Option D

For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Description : For a longitudinal reinforcing bar in a column, the minimum cover shall neither be less than the diameter of bar nor less than (A) 15 mm (B) 25 mm (C) 30 mm (D) 40 mm

Last Answer : Answer: Option D

For a poorly graded sub-grade soil, thickness of sub-base, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 30 cm

Description : For a poorly graded sub-grade soil, thickness of sub-base, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 30 cm

Last Answer : Answer: Option D

Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Description : Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Last Answer : (A) 10 cm

The thickness of a reinforced brick partition wall, is generally kept (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : The thickness of a reinforced brick partition wall, is generally kept (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 m

Description : An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 mm

Last Answer : Answer: Option D

A column is regarded as long column if the ratio of its effective length and lateral dimension, exceeds (A) 10 (B) 15 (C) 20 (D) 25

Description : A column is regarded as long column if the ratio of its effective length and lateral dimension, exceeds (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option B

For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Description : For normal cases, stiffness of a simply supported beam is satisfied if the ratio of its span to its overall depth does not exceed (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m

Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the  sight on the down-slope, must be less than  (A) 30 m  (B) 25 m  (C) 20 m  (D) 15 m 

Last Answer : (B) 25 m 

For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Description : For the design of a simply supported T-beam the ratio of the effective span to the overall depth of the beam is limited to (A) 10 (B) 15 (C) 20 (D) 25

Last Answer : Answer: Option C

For a comfortable travel on Highways, the centrifugal ratio should not exceed (A) 0.10 (B) 0.15 (C) 0.20 (D) 0.25

Description : For a comfortable travel on Highways, the centrifugal ratio should not exceed (A) 0.10 (B) 0.15 (C) 0.20 (D) 0.25

Last Answer : Answer: Option D

direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure developed during the test (C) As the test progresses the area under shear, gradually changes (D) None of these

Description : direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure ... C) As the test progresses the area under shear, gradually changes (D) None of these

Last Answer : Answer: Option C

The condition will be called as thin flange, when the flange thickness becomes less the: (a) 10mm (b) 12mm (c) 16mm* (d) 15mm

Description : The condition will be called as thin flange, when the flange thickness becomes less the: (a) 10mm (b) 12mm (c) 16mm* (d) 15mm

Last Answer : (c) 16mm*

To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Description : To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Last Answer : Answer: Option D

The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm

Description : The thickness of bituminous carpet varies from (A) 20 to 25 mm (B) 50 to 75 mm (C) 75 to 100 mm (D) 100 to 120 mm

Last Answer : Answer: Option A

The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Less than 1 in beams but greater than 1 in channels

Description : The ratio of the thickness of web to that of flange of steel rolled structural beams and channels is (A) Less than 1 (B) Equal to 1 (C) Greater than 1 (D) Less than 1 in beams but greater than 1 in channels

Last Answer : Answer: Option A

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Last Answer : Answer: Option B

The minimum diameter of a sewer is kept A. 10 cm B. 15 cm C. 20 cm D. 25 cm

Description : The minimum diameter of a sewer is kept A. 10 cm B. 15 cm C. 20 cm D. 25 cm

Last Answer : ANS: B

To prevent movement of moisture from sub-grade to road pavement at the same level as that of water-table, thickness of a cut off layer of coarse sand, is (A) 15 cm (B) 20 cm (C) 30 cm (D) 45 cm

Description : To prevent movement of moisture from sub-grade to road pavement at the same level as that of water-table, thickness of a cut off layer of coarse sand, is (A) 15 cm (B) 20 cm (C) 30 cm (D) 45 cm

Last Answer : Answer: Option A

For compacting plain concrete road surface of thickness less than 20 cm, we use (A) Internal vibrator (B) Screed vibrator (C) Form vibrator (D) None of these

Description : For compacting plain concrete road surface of thickness less than 20 cm, we use (A) Internal vibrator (B) Screed vibrator (C) Form vibrator (D) None of these

Last Answer : Answer: Option B

For compacting plain concrete road surface of thickness less than 20 cm, the following vibrator is used. [ A ] Internal vibrator [ B ] Screed vibrator [ C ] Form vibrator [ D ] None of the above

Description : For compacting plain concrete road surface of thickness less than 20 cm, the following vibrator is used. [ A ] Internal vibrator [ B ] Screed vibrator [ C ] Form vibrator [ D ] None of the above

Last Answer : [ B ] Screed vibrator

Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its(A) Inner diameter(B) Outer diameter(C) Thickness(D) Neither inner nor outer diameter

Description : Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its (A) Inner diameter (B) Outer diameter (C) Thickness (D) Neither inner nor outer diameter

Last Answer : (D) Neither inner nor outer diameter

Vessel is said to be thin if a. D/t =20 b. D/t=10 c. D/t >20 d. D/t >10

Description : Vessel is said to be thin if a. D/t =20 b. D/t=10 c. D/t >20 d. D/t >10

Last Answer : c. D/t >20

An internal mouthpiece is said to be running free if the length of the mouthpiece is __________ the diameter of the orifice. (A) Less than twice (B) More than twice (C) Less than three times (D) More than three times

Description : An internal mouthpiece is said to be running free if the length of the mouthpiece is __________ the diameter of the orifice. (A) Less than twice (B) More than twice (C) Less than three times (D) More than three times

Last Answer : Answer: Option C

The minimum cover to the ties or spirals should not be less than (A) 15 mm (B) 20 mm (C) 25 mm (D) 50 mm

Description : The minimum cover to the ties or spirals should not be less than (A) 15 mm (B) 20 mm (C) 25 mm (D) 50 mm

Last Answer : Answer: Option C

For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30

Description : For a given material Young's modulus is 200 GN/m2 and modulus of rigidity is 80 GN/m2 . The value of Poisson's ratio is (A) 0.15 (B) 0.20 (C) 0.25 (D) 0.30

Last Answer : (C) 0.25