Pick out the wrong statement. (A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1 (B) For calculating forces and efficiency of riveted joint, either rivet diameter or rivet hole diameter is used in case of pressure vessel and in structural work (C) Longitudinal joint is normally made butt joint to maintain the circularity of the vessel (D) Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm

Pick out the wrong statement.
(A) For a pressure vessel to be classified as 'thin vessel', the ratio of wall
thickness to mean radius is less than 0.1
(B) For calculating forces and efficiency of riveted joint, either rivet
diameter or rivet hole diameter is used in case of pressure vessel and in structural
work
(C) Longitudinal joint is normally made butt joint to maintain the circularity
of the vessel
(D) Maximum diameter of the opening provided in a pressure vessel, which
does not require any compensation is 200 mm
by

1 Answer

Answer :

Option B
by

Related questions

The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Description : The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Last Answer : Option A

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (i) Butt joint

Failure of riveted joints is due to (A) Tearing of the plates between the rivet hole and the edge of the plate (B) Tearing of plates between rivets (C) Shearing of rivets (D) All the above

Description : Failure of riveted joints is due to  (A) Tearing of the plates between the rivet hole and the edge of the plate  (B) Tearing of plates between rivets  (C) Shearing of rivets  (D) All the above 

Last Answer : (D) All the above 

Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the possibility of tower wall collapse (B) Packed towers are preferred over plate towers for handling corrosive and foamy liquids (C) Diameter of randomly packed tower is normally more than 1.2 metres (D) Due to uneven supply and improper distribution of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Description : Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the ... of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Last Answer : (C) Diameter of randomly packed tower is normally more than 1.2 metres

The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Description : The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Last Answer : c) 21.5 mm*

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Description : Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Last Answer : (D) 40

Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Description : Cylinder having inner diameter to wall thickness ratio less than 15 are a) Thin cylinders b) Thick Cylinders c) Moderate cylinders d) none of the above

Last Answer : b) Thick Cylinders

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Description : When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Last Answer : (D) Double riveted double cover butt joint

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm

Last Answer : (D) 200 mesh screen has 200 openings per linear cm

Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a measure of its capacity and is equal to the residence time when the density of reaction mixture is constant (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty (D) In an ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Description : Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a ... ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Last Answer : (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Last Answer : Answer: Option C

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Description : An open-ended cylinder of radius and thickness is subjected to internal pressure . The Young's modulus for the material is and Poisson's ratio is . The longitudinal strain is (A) Zero (B) pr/TE (C) pr/2TE (D) None of these

Last Answer : (A) Zero

Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or thermosetting (C) Branching in case of cross-linked polymers caused by small amount of impurities in bifunctional monomer formulation reduces its solubility and increases the softening point (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Description : Pick out the wrong statement. (A) Linear polymers are formed from bifunctional groups only and are normally thermoplastic (B) Cross-linked branched chain polymers are either elastometric or ... (D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Last Answer : D) Dibasic acids reacts with dihydric alcohols to give polyesters using addition polymerisation reaction

Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Description : Root and face bends from an 8mm thick butt weld require testing. The specimens are cut to 20mm wide. The code calls for a 4t bend. Which of the following rollers should be selected for the testing? a) 50mm radius b) 50mdiameter c) 32mm radius d) 32mm diameter

Last Answer : d) 32mm diameter

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

According to Unwin's formula, the diameter of a rivet of plate of thickness is : (A) d = 6.05 t (B) d = 1.5 t + 4 (C) d = t(D) d = t + 1.5

Description : According to Unwin's formula, the diameter of a rivet of plate of thickness is :  (A) d = 6.05 t (B) d = 1.5 t + 4  (C) d = t (D) d = t + 1.5 

Last Answer : (A) d = 6.05 t

Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (ii) Lap joint

Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Description : Pick out the wrong statement. (A) Trouton's ratio of non-polar liquids is calculated using Kistyakowsky equation (B) Thermal efficiency of a Carnot engine is always less than 1 (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation (D) None of these

Last Answer : (C) An equation relating pressure, volume and temperature of a gas is called ideal gas equation

Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ions and forms amino acids(B) Calcium present in the fertiliser helps in correcting the soil acidity(C) Particle size range of a good granular fertiliser is 10-15 mesh and itcontains less moisture as compared to finely divided powder form of fertiliser(D) Ammonium nitrate fertiliser is obtained as a by-product in an integratedsteel plant having by-product coke ovens

Description : Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ... nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

Last Answer : (D) Ammonium nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

Pick out the wrong statement. (A) A ferromagnetic material becomes paramagnetic above the 'Curie temperature' (B) Permanent magnets are made of hard materials, whereas electromagnets require soft magnetic materials (C) Soft magnetic materials (e.g., pure iron) have higher permeability and low hysterisis loss and coercive forces (D) Tungsten steel and alnico are not hard magnetic materials

Description : Pick out the wrong statement. (A) A ferromagnetic material becomes paramagnetic above the 'Curie temperature' (B) Permanent magnets are made of hard materials, whereas electromagnets require soft ... hysterisis loss and coercive forces (D) Tungsten steel and alnico are not hard magnetic materials

Last Answer : Option D

Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Last Answer : c. Greater

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Description : A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Last Answer : (D) 1/10

Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given ‘L/V’ ratio (B) The extraction per unit of total height for a short packed column is more effective than for a tall column, in case of liquid-liquid extraction(C) Natural draft cooling towers are made of ferroconcrete and its cross￾section is wider at the bottom(D) Vander wall adsorption is also called chemisorption

Description : Pick out the wrong statement. (A) With decrease in feed temperature, the number of plates required for binary distillation decreases for a given L/V' ratio (B) The extraction per unit ... and its cross￾section is wider at the bottom (D) Vander wall adsorption is also called chemisorption

Last Answer : (D) Vander wall adsorption is also called chemisorption

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Description : A spherical pressure vessel is made of thin magnesium plate 0.25 cm thick. The main diameter of the sphere is 600 cm and allowable stress in tension is 900 kg/cm2. The safe internal gas pressure for the vessel would be a) 0.5 kg/cm2 b) 1.5 kg/cm2 c) 4.5 kg/cm2 d) 5.7 kg/cm2

Last Answer : b) 1.5 kg/cm2

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is called the Stanton number (C) The Peclet number is a measure of the ratio of energy transport by convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Description : Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is ... convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Last Answer : (D) The Colburn jH factor for heat transfer is given by Nst Npr

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Last Answer : A. 575

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Last Answer : a) 575

Pick out the correct statement. (A) Compression ratio of an Otto engine is comparatively higher than a diesel engine (B) Efficiency of an Otto engine is higher than that of a diesel engine for the same compression ratio (C) Otto engine efficiency decreases with the rise in compression ratio, due to decrease in work produced per quantity of heat (D) Diesel engine normally operates at lower compression ratio than an Otto engine for an equal output of work

Description : Pick out the correct statement. (A) Compression ratio of an Otto engine is comparatively higher than a diesel engine (B) Efficiency of an Otto engine is higher than that of a diesel ... Diesel engine normally operates at lower compression ratio than an Otto engine for an equal output of work

Last Answer : (B) Efficiency of an Otto engine is higher than that of a diesel engine for the same compression ratio

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160

Description : A circular solid of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates at 600 rpm, the kinetic energy of the flywheel, in joules is 1. 395 2. 790 3. 1580 4. 3160

Last Answer : 2. 790

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

Pick out the wrong statement. (A) Surface tension of a liquid is because of the difference in magnitude of adhesive & cohesive forces(B) A hydrometer used for the determination of specific gravities of liquidsworks on the principle of buoyant forces(C) In case of unsteady fluid flow, the velocity at any given point does notchange with time(D) Turbulent fluid flow is characterised by the rapid fluctuation ofinstantaneous pressure & velocity at a poin

Description : Pick out the wrong statement. (A) Surface tension of a liquid is because of the difference in magnitude of adhesive & cohesive forces (B) A hydrometer used for the determination of ... Turbulent fluid flow is characterised by the rapid fluctuation of instantaneous pressure & velocity at a poin

Last Answer : (C) In case of unsteady fluid flow, the velocity at any given point does not change with time

Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Description : Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2.k), when the insulation thickness is __________ mm. (A) 15 (B) 25 (C) 10 (D) 30

Last Answer : (B) 25

A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None

Description : A thin cylindrical under internal pressure can fail along the a. Longitudinal joint b. Circumferential joint c. Longitudinal as well as circumferential joint d. None

Last Answer : c. Longitudinal as well as circumferential joint

Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Description : Pick out the wrong statement. (A) Reciprocal of the resistance to heat flow is called thermal conductance (B) Unit of thermal conductance is W/°K (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A (D) None of these

Last Answer : (C) Thermal conductance of a wall of thickness 'L', thermal conductivity 'k' and heat flow area 'A' is kL/A

The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Description : The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Last Answer : Answer: Option B

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

In case of an eccentric loading on a bracket subjected to moment M, the tangential force developed in any rivet, at right angles to its radius vector r is (A) Mr/ r² (B) r²/Mr(C) Mr²/ r² (D) Mr/ r²

Description : In case of an eccentric loading on a bracket subjected to moment M, the tangential force  developed in any rivet, at right angles to its radius vector r is  (A) Mr/ r²  (B) r²/Mr (C) Mr²/ r²  (D) Mr/ r² 

Last Answer : (A) Mr/ r²