A three phase induction motor is drawing 16 Ampere at 440 Volts. If the operating power factor of the motor is 0.90 and the motor efficiency is 92%, then the mechanical shaft power output of the motor is a) 12.04 kW b) 10.09 kW c) 10.97 kW d) None of the above

A three phase induction motor is drawing 16 Ampere at 440 Volts. If the operating

power factor of the motor is 0.90 and the motor efficiency is 92%, then the mechanical

shaft power output of the motor is

a) 12.04 kW b) 10.09 kW

c) 10.97 kW d) None of the above
by

1 Answer

Answer :

b) 10.09 kW
by

Related questions

The power generation potential in mini hydro power plant for a water flow of 3 m3 /sec with a head of 14 meters and with a system efficiency of 55% is a) 226.6 kW b) 76.4 kW c) 23.1 kW d) none of the above

Description : The power generation potential in mini hydro power plant for a water flow of 3 m3 /sec with a head of 14 meters and with a system efficiency of 55% is a) 226.6 kW b) 76.4 kW c) 23.1 kW d) none of the above

Last Answer : a) 226.6 kW

A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Description : A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Last Answer : Answer: B

Which of the following statements are true? i) reactive current is necessary to build up the flux for the magnetic field of inductive devices ii) some portion of reactive current is converted into work iii) the cosine of angle between kVA and kVAr vector is called power factor iv) the cosine of angle between kW and kVA vector is called power factor a) i & iv b) ii & iii c) i & iii d) iii & iv

Description : Which of the following statements are true? i) reactive current is necessary to build up the flux for the magnetic field of inductive devices ii) some portion of reactive current is converted into work iii) the cosine of angle ... called power factor a) i & iv b) ii & iii c) i & iii d) iii & iv

Last Answer : a) i & iv

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Description : A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Last Answer : Answer: C

A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Last Answer : Answer: B

The component of electric power which yields useful mechanical power output is known as a) apparent power b) active power c) reactive power d) none of the above

Description : The component of electric power which yields useful mechanical power output is known as a) apparent power b) active power c) reactive power d) none of the above

Last Answer : b) active power

2000 kJ of heat is supplied to 500 kg of ice at 0oC. If the latent heat of fusion of ice is 335 kJ/kg then the amount of ice in kg melted will be a) 1.49 b) 83.75 c) 5.97 d) None of the above

Description : 2000 kJ of heat is supplied to 500 kg of ice at 0oC. If the latent heat of fusion of ice is 335 kJ/kg then the amount of ice in kg melted will be a) 1.49 b) 83.75 c) 5.97 d) None of the above

Last Answer : c) 5.97

The energy conversion efficiency of a solar cell does not depend on a) solar energy insolation b) inverter c) area of the solar cell d) maximum power output

Description : The energy conversion efficiency of a solar cell does not depend on a) solar energy insolation b) inverter c) area of the solar cell d) maximum power output

Last Answer : b) inverter

An electric heater draws 5 kW of power for continuous hot water generation in an industry. How much quantity of water in litres per min can be heated from 30oC to 85oC ignoring losses?. a) 1.3 b) 78.18 c) 275 d) none of the above

Description : An electric heater draws 5 kW of power for continuous hot water generation in an industry. How much quantity of water in litres per min can be heated from 30oC to 85oC ignoring losses?. a) 1.3 b) 78.18 c) 275 d) none of the above

Last Answer : a) 1.3

The electrical power unit Giga Watt (GW) may be written as a) 1,000,000 MW b) 1,000 MW c) 1,000 kW d) 1,000,000 W

Description : The electrical power unit Giga Watt (GW) may be written as a) 1,000,000 MW b) 1,000 MW c) 1,000 kW d) 1,000,000 W

Last Answer : b) 1,000 MW

The energy consumption and production patterns in a chemical plant over a 9 month period is provided in the table below; Month 1 2 3 4 5 6 7 8 9 Production in Tonnes / month 493 297 381 479 585 440 234 239 239 Energy Consumption MWh /month 78.2 75.7 76.3 76.1 78.1 70.7 73.7 64.4 72.1 Estimate the cumulative energy savings at end of the 9th month and give your inference on the result ? ( consider 9 month data for evaluation for predicted energy consumption)

Description : The energy consumption and production patterns in a chemical plant over a 9 month period is provided in  the table below; Month 1 2 3 4 5 6 7 8 9 Production in Tonnes / month 493 ... and give your inference on the  result ? ( consider 9 month data for evaluation for predicted energy consumption)

Last Answer : It is required to use the equations Y= mX + C and  nC + mΣX = ΣY  cΣX + mΣX2 = ΣXY Month X =  Production in  Tonnes /  month Y =Energy  Consumption MWh  /month  X 2 XY 1 493 78.2 ... 73.7 54756 17240.63 8 239 64.4 57121 15402.96 9 239 72.1 57121 17228.98 3387 665.3 1410683 253221

A 3 phase, 400 volts, 50 Hz, 100 kW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a...

Description : A 3 phase, 400 volts, 50 Hz, 100 kW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of: (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm

Last Answer : 1470rpm

n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In each batch about 120 kgs of material is dried. a. The quantity of moisture removed per batch. b. What is the total quantity ( sensible & latent) of heat required to evaporate the moisture, if the latent heat of water is 540 kcal/kg at atmospheric conditions, Ignore heat absorbed by the solids c. Find the quantity of steam required for the drying process (per batch), if steam at 4 kg/cm2 is used for generating hot air in the dryer and the dryer efficiency is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.

Description : n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture  is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In  each batch about 120 ... dryer and the dryer efficiency  is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.

Last Answer : Given that   Qty of material dried per batch - 120 Kgs  Moisture at inlet - 60% a. The quantity of moisture removed per batch.  Water quantity in a wet batch - 120 x 0.6 = 72 Kgs.  Quantity of bone dry ... - 48/0.95 = 50.5 Kgs.  Equivalent water in a dry batch - 50.5 - 48 = 2.5 Kgs.

An oil fired boiler is retrofitted to fire coconut shell chips. Boiler thermal efficiency drops from 82% to 70%. What will be the percentage change in energy consumption to generate the same output a) 12% increase b) 14.6% increase c) 17.1% decrease d) 17.1% increase

Description : An oil fired boiler is retrofitted to fire coconut shell chips. Boiler thermal efficiency drops from 82% to 70%. What will be the percentage change in energy consumption to generate the same output a) 12% increase b) 14.6% increase c) 17.1% decrease d) 17.1% increase

Last Answer : d) 17.1% increase

In a manufacturing plant, following data are gathered for a given month: Production - 1200 pieces; specific energy consumption - 1000 kWh/piece; variable energy consumption - 950 kWh/piece. The fixed energy consumption of the plant for the month Paper 1 –Set A with Solutions _______________________ Bureau of Energy Efficiency 6 is ------- a) 6,000 kWh b)10,000 kWh c) 12,000 kWh d) 60,000 kWh

Description : In a manufacturing plant, following data are gathered for a given month: Production - 1200 pieces; specific energy consumption - 1000 kWh/piece; variable energy consumption - 950 kWh/piece. The fixed energy consumption of the plant ... ----- a) 6,000 kWh b)10,000 kWh c) 12,000 kWh d) 60,000 kWh

Last Answer : d) 60,000 kWh

Which one is not an energy consumption benchmark parameter? a) kcal/kWh of electricity generated b) kg/ oC. c) kW/ton of refrigeration d) kWh/kg of yarn

Description : Which one is not an energy consumption benchmark parameter? a) kcal/kWh of electricity generated b) kg/ oC. c) kW/ton of refrigeration d) kWh/kg of yarn

Last Answer : b) kg/ oC.

The benchmarking parameter for a vapour compression refrigeration system is a) kW / kg of refrigerant used b) kcal / m3 of chilled water c) BTU / Ton of Refrigeration d) kW / Ton of Refrigeration

Description : The benchmarking parameter for a vapour compression refrigeration system is a) kW / kg of refrigerant used b) kcal / m3 of chilled water c) BTU / Ton of Refrigeration d) kW / Ton of Refrigeration

Last Answer : d) kW / Ton of Refrigeration

A building intended to be used for commercial purpose will be required to follow Energy conservation building code under Energy Conservation Act, 2001 provided its a) connected load is 120 kW and above b) contract demand is 100 kVA and above c) connected load is100 kW and above or contract demand is 120 kVA and above

Description : A building intended to be used for commercial purpose will be required to follow Energy conservation building code under Energy Conservation Act, 2001 provided its a) connected load is 120 kW and above b) ... and above c) connected load is100 kW and above or contract demand is 120 kVA and above

Last Answer : c) connected load is100 kW and above or contract demand is 120 kVA and above

A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging.

Description : A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the ... the motor will be (A) 23.06 kW (B) 24.11 kW (C) 25.01 kW (D) 26.21 kW

Last Answer : A 400 V, 50 Hz 30 hp, three-phase induction motor is drawing 50 A current at 0.8 power factor lagging. The stator and rotor copper losses are 1.5 kW and 900 W respectively. The friction and windage losses are 1050 W and the core losses are 1200 W. The air-gap power of the motor will be 25.01 kW

A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw

Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw

Last Answer : Answer: C

The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be (A) 600 W. (B) 625 W (C) 650 W (D) 700 W

Description : The rotor power output of a 3-phase induction motor is 15 KW and corresponding slip is 4%. The rotor copper loss will be (A) 600 W. (B) 625 W (C) 650 W (D) 700 W

Last Answer : Ans: B Rotor copper losses = rotor input- rotor output and output = (1-s) input ∴ Input = output/(1-s) = 15000 /1-0.04 = 15625 ∴ loss = 15625 -1500 = 625 watt

The rotor power output of a 3 -phase induction motor is 15 kW and the corresponding slip is 4%. The rotor..

Description : The rotor power output of a 3 -phase induction motor is 15 kW and the corresponding slip is 4%. The rotor copper losses will be: (A) 600 W (B) 625 W (C) 650 W (D) 700 W

Last Answer : The rotor power output of a 3 -phase induction motor is 15 kW and the corresponding slip is 4%. The rotor copper losses will be: 625 W

Which of the following statements is correct concerning the motor performance curves and data table shown in the illustration? EL-0006 A. The motor RPM at full load is 1737 RPM. B. The motor draws 12.62 kw from the switchboard when operating at full load. C. If the motor was developing 10 HP its power factor would be 0.92. D. All of the above.

Description : Which of the following statements is correct concerning the motor performance curves and data table shown in the illustration? EL-0006 A. The motor RPM at full load is 1737 RPM. B. The motor draws 12.62 kw ... If the motor was developing 10 HP its power factor would be 0.92. D. All of the above.

Last Answer : Answer: D

In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace, producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 TPD GCV of coal : 4500 kcal/kg Power Purchased from Grid : 82400 kWh / day Specific Energy consumption for Kiln producing Sponge Iron: 120 kWh / ton sponge iron Calculate the following 1. Specific Energy Consumption of Induction melting furnace in terms of kWh/ton of molten steel 2. Specific Energy Consumption of the entire plant, in terms of kcal/kg of molten steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Description : In a 100 TPD Sponge Iron plant, the sponge iron is fed to the Induction melting furnace,  producing molten steel at 88% yield. The Energy consumption details are as follows: Coal Consumption : 130 ... molten  steel (product). 3. Total Energy Consumption of Plant in Tons of Oil Equivalent (TOE )

Last Answer :  a) Specific Energy Consumption of Induction Melting Furnace  Molten Steel Production from the Induction melting furnace per day  = 100 x 88/100 = 88 TPD Total Energy Consumption of the Plant = 82400 kWh ... mark c) Total Energy consumption of Plant in ToE  = 655864000/107  = 65.586 ToE

Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the blanks 3 Non Contact Infrared Thermometer cannot measure temperature of objects placed in hazardous places True/False 4 To measure the RPM of a Flywheel, ______ type of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used. Fill in the blanks 5 In a switch yard, _____ instrument is used to identify the loose joints and terminations Fill in the blanks 6 Every Designated Consumer shall have its first energy audit conducted by ________ Energy Auditor within ______ months of

Description :  Answer the following S. No Statement Chose the correct  answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM  meter is used and for a visible shaft-end _______ type of  RPM meter is used.

Last Answer : Sr  No Statement Chose the correct  answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and  SO2 True/False False 2 Ultrasonic Flow Meter uses the  principle of____& ____ ... ]  10 In a gasification system the  reduction zone is above the  combustion zone True/False False

To maximize the combustion efficiency, which of the following in the flue gas needs to be done? a) maximize O2 b) maximize CO2 c) minimize CO2 d) maximize CO

Description : To maximize the combustion efficiency, which of the following in the flue gas needs to be done? a) maximize O2 b) maximize CO2 c) minimize CO2 d) maximize CO

Last Answer : b) maximize CO2

In a boiler, fuel substitution of coal with rice husk results in a) energy conservation b) energy efficiency c) both energy conservation and energy efficiency d) carbon neutrality

Description : In a boiler, fuel substitution of coal with rice husk results in a) energy conservation b) energy efficiency c) both energy conservation and energy efficiency d) carbon neutrality

Last Answer : d) carbon neutrality

Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Description : Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Last Answer : a) Dry Bulb Temperature and Wet bulb Temperature Dry bulb Temperature is an indication of the sensible heat content of air-water vapour  mixtures Wet bulb Temperature is a measure of ... of capital cost. This is a broad indicator of the annual return expected from initial capital investment

Assume CO2 equivalent emissions by the use of a 60 W incandescent lamp are of the order of 60 g/hr. If it is replaced by a 5 W LED lamp then the equivalent CO2 emissions will be a) nil b) 5 g/hr c) 12 g/hr d) 300 g/hr

Description : Assume CO2 equivalent emissions by the use of a 60 W incandescent lamp are of the order of 60 g/hr. If it is replaced by a 5 W LED lamp then the equivalent CO2 emissions will be a) nil b) 5 g/hr c) 12 g/hr d) 300 g/hr

Last Answer : b) 5 g/hr

A 400kW, 3-phase, 440V, 50Hz induction motor has a speed of 950 r.p.m. on fullload. The machine has 6 poles. The slip of the machine will be _______________. (A) 0.06 (B) 0.10 (C) 0.04 (D) 0.05

Description : A 400kW, 3-phase, 440V, 50Hz induction motor has a speed of 950 r.p.m. on fullload. The machine has 6 poles. The slip of the machine will be _______________. (A) 0.06 (B) 0.10 (C) 0.04 (D) 0.05

Last Answer : Ans: D N = Ns (1-S) 950 = 120 x 50 (1-S)/6 S = 0.05

What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Description : What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Last Answer : Answer: D

A project activity has several components as indicated below; S. No. Activity Preceded by Duration (in Weeks) 1 A - 8 2 B A 6 3 C A 12 4 D B 4 5 E D 5 6 F B 12 7 G E& F 9 8 H C 8 9 I F & H 5 10 J I & G 6 d. Prepare a PERT chart, estimate the duration of the project and identify the critical path.

Description : A project activity has several components as indicated below; S.  No. Activity Preceded by Duration (in  Weeks) 1 A - 8 2 B A 6 3 C A 12 4 D B 4 5 E D 5 6 F B 12 7 G E& F ... H 5 10 J I & G 6 d. Prepare a PERT chart, estimate the duration of the project and identify the  critical path.

Last Answer : PERT Diagram based on Activity on Arrow  .  E  D 5 G B 5 9 J, 6 A 6 F,12 I ,5 8 c 12 H 8 OR  PERT Diagram based on Activity on Node …………………….6 marks a. Critical Path: A-B-F-G-J …………………….1 mark  b. Estimated Project Duration: 41 weeks

A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately

Description : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the ... at half the rated speed is  (A) 0.354 (B) 0.372 (C) 0.90 (D) 0.955

Last Answer : A three-phase, 440 V, 50 Hz ac mains fed thyristor bridge is feeding a 440 V dc, 15 kW, 1500 rpm separately excited dc motor with a ripple free continuous current in the dc link under all operating conditions, Neglecting the losses, the power factor of the ac mains at half the rated speed is 0.354

A manufacturing industry plans to improve its energy performance under PAT through implementation of an energy conservation scheme. After implementation, calculate the Plant Energy Performance (PEP) with 2015-16 as the reference year. What is your inference? Given that:  The current year (2016-17 ) Annual Production – 28,750 T ,  Current year (2016-17 ) Annual Energy Consumption– 23,834 MWh,  Reference year (2015-16 ) production - 34,000 T,  Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Description : A manufacturing industry plans to improve its energy performance under PAT through  implementation of an energy conservation scheme. After implementation, calculate the  Plant Energy Performance (PEP) with 2015-16 as the ... 34,000 T,   Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Last Answer : Production factor (PF) = 28750/34000 = 0.846 …………………….1 mark Ref year equivalent energy (RYEE) = Ref Year Energy Use (RYEU) x PF   = 27,200 x 0.846= 23011MWh

A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Description : A 3-phase 50HZ SCIM takes a power input of 30 KW at its full load speed of 1440 rpm. Total stator losses are 1 KW. The slip and rotor ohmic losses at full load are a) 0.02, 600 W b) 0.04, 580 W c) 0.04, 1160 W d) 0.04, 1200 W

Last Answer : Ans: 0.04, 1160 W

The rotor frequency for a 3 phase 1000 RPM 6 pole induction motor with a slip of 0.04 is________Hz (A) 8 (B) 4 (C) 6 (D) 2

Description : The rotor frequency for a 3 phase 1000 RPM 6 pole induction motor with a slip of 0.04 is________Hz (A) 8 (B) 4 (C) 6 (D) 2

Last Answer : Ans: D Given: N=1000 rpm ; P= 6; s= 0.04; and f = NP/ 120 = 10006/120 = 50 Hz Rotor frequency fr=sf = 0.0450 = 2.0 Hz

The rotor frequency for a 3-phase 6-pole, 1000 r.p.m. induction motor with a slip of 0.04 is

Description : The rotor frequency for a 3-phase 6-pole, 1000 r.p.m. induction motor with a slip of 0.04 is (a) 2 Hz (b) 4 Hz (c) 6 Hz (d) 8 Hz  

Last Answer : 2hz is rotor frequency

A company has to choose between two projects whose cash flows are as indicated below; Project 1: i. Investment – Rs. 15 Lakhs ii. Annual cost savings – Rs. 4 lakhs. iii. Bi-annual maintenance cost – Rs. 50,000/- iv. Reconditioning and overhaul during 5th year: 6 lakhs v. Life of the project – 8 years vi. Salvage value – Rs. 5 lakhs Project 2: vii. Investment – Rs. 14 Lakhs viii. Annual cost savings – Rs. 3.5 lakhs. ix. Annual Maintenance cost – Rs. 20,000/- x. Reconditioning and overhaul during 4th year: 5 lakhs xi. Life of the project – 8 years xii. Salvage Value- 2 lakhs Which project should the company choose? The annual discount rate is 12

Description :  A company has to choose between two projects whose cash flows are as indicated  below; Project 1:  i. Investment - Rs. 15 Lakhs ii. Annual cost savings - Rs. 4 lakhs. iii. Bi-annual ... years xii. Salvage Value- 2 lakhs Which project should the company choose? The annual discount rate is 12

Last Answer : Year Project 1 Project 2 Outgo Saving NPV Outgo Saving NPV 0 15.0 0 =-15.0 14.0 0 = -14 1 0 4.0 = (4 / (1+.12)1 = 3.571 0.2 3.5 = (3.3 / (1+.12)1 = 2.95 2 0.5 4.0 = (3.5 / (1+.12)2 = 2.79 0.2 3.5 ... (1+.12)8 = 3.43 0.2 5.5  (3.5+2) = (5.3 / (1+.12)8 = 2.14 NPV = + 2.301 @12% = + 0.15

[23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Description : [23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Last Answer : C. Total transformer loss depends on volt ampere

A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the

Description : A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the machine at full load is  (A) 1.66 Nm (B) 95.50 Nm (C) 99.47 Nm (D) 624.73 Nm

Last Answer : A 400 V, 15 kW, 4-pole, 50 Hz, Y-connected induction motor has full load slip of 4%. The output torque of the machine at full load is 99.47 Nm

Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'D' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: A

Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'C' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: C

Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'B' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Description : Figure 'A' of the diagram shown in the illustration has a turns ratio of four to one. If a three-phase 440 volt supply is connected to terminals 'A-B-C', what voltage should develop across terminals 'a-b-c'? EL-0084 A. 64 volts B. 110 volts C. 190 volts D. 762 volts

Last Answer : Answer: B

The output from a power shovel is 144 cum/hr. The required number of trucks of 12 cum capacity each with 16 minute cycle time and with 80% operating efficiency will be (a) 5 (b) 4 (c) 3 (d) 2

Description : The output from a power shovel is 144 cum/hr. The required number of trucks of 12 cum capacity each with 16 minute cycle time and with 80% operating efficiency will be (a) 5 (b) 4 (c) 3 (d) 2

Last Answer : (c) 3

A 3-phase, 400 votts, 50 Hz, 100 KW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm

Description : A 3-phase, 400 votts, 50 Hz, 100 KW, 4 pole squirrel cage induction motor with a rated slip of 2% will have a rotor speed of (A) 1500 rpm (B) 1470 rpm (C) 1530 rpm (D) 1570 rpm

Last Answer : Ans: B N = NS (1-S) and NS =120 f / p =120 x 50 /4 = 1500 rpm ∴N= 1500 (1-0.02) =1470 rpm

The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated

Description : The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor ... Hz supply is  (A) 58.5 A (B) 45.0 A (C) 42.7 A (D) 55.6 A

Last Answer : The locked rotor current in a 3-phase, star connected 15 , kW 4 , pole 230 V , 50 Hz induction motor at rated conditions is 50 A. Neglecting losses and magnetizing current, the approximate locked rotor line current drawn when the motor is connected to a 236 , V 57 Hz supply is 45.0 A