Description : When the RET instruction at the end of subroutine is executed, a. the information where the stack is iniatialized is transferred to the stack pointer b. the memory address of the RET instruction is ... two data bytes stored in the top two locations of the stack are transferred to the stack pointer
Last Answer : c. two data bytes stored in the top two locations of the stack are transferred to the program counter
Description : When a subroutine is called, the address of the instruction following the CALL instructions stored in/on the a. stack pointer b. accumulator c. program counter d. stack
Last Answer : d. stack
Description : The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit
Last Answer : c) 40, 8 bit
Description : The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit d) 40, 8 byte
Description : A stack pointer is a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory. b. a register that decodes and executes 16-bit arithmetic expression. c. The first memory location where a subroutine address is stored. d. a register in which flag bits are stored
Last Answer : a. a 16-bit register in the microprocessor that indicate the beginning of the stack memory.
Description : Which of the following registers is used to keep track of address of the memory location where the next instruction is located? a. Memory Address Register b. Memory Data Register c. Instruction Register d. Program Register
Last Answer : d. Program Register
Description : Which of the following registers is used to keep track of address of the memory location where the next instruction is located? a. Memory address register b. Memory data register c. Instruction register d. Program counter
Last Answer : d. Program counter
Description : Which of the following registers is loaded with the contents of the memory location pointed by the PC? a. Memory address register b. Memory data register c. Instruction registers d. Program counter
Last Answer : c. Instruction registers
Description : Which of the following registers is loaded with the contents of the memory location pointed by the PC? a. Memory address registers b. Memory data registers c. Instruction register d. Program counter
Last Answer : c. Instruction register
Description : If the three points (k, 2k), (2k, 3k) and (3, 1) are collinear then k is equal to -Maths 9th
Last Answer : (d) 3Let (x, y) be the co-ordinates of the third vertex of the triangle. Then\(rac{0+2+x}{3}\) = 1 and \(rac{0+0+y}{3}\) = 1⇒ 2 + \(x\) = 3 and y = 3 ⇒ \(x\) = 1, y = 3. ∴ Co-ordinates of vertices of the triangle ... - y3) + x2 (y2 - y3) + x3(y1 - y2)]= \(rac{1}{2}\) [0+6+0] = \(rac{6}{2}\) = 3.
Description : For a given material, if E, C, K and m are Young's modulus, shearing modulus, bulk modulus and Poisson ratio, the following relation does not hold good (A) E = 9KC/3K + C (B) E = 2K (1 + 2/m) (C) E = 2C (1 + 1/m) (D) E = 3C (1 - 1/m)
Last Answer : (C) E = 2C (1 + 1/m)
Description : The relationship between Young’s modulus (E), Bulk modulus (K) and Poisson’s ratio (μ) is given by a. E=2K(1-2μ) b. E=3K(1-2μ) c. E=2K(1-2μ) d. E=2K(1-3μ)
Last Answer : b. E=3K(1-2μ)
Description : Return instruction is written in_ to written to main program: a. Subroutine b. Main program c. Botha &b d. None of these
Last Answer : a. Subroutine
Description : When subroutine is called contents of program counter is location address of __ instruction following call instruction is stored on _ __and program execution is transferred to __ address. a. Non ... , Stack and Main program Cc. Executable, Queue and Subroutine d. Executable, Stack and Subroutine
Last Answer : d. Executable, Stack and Subroutine
Description : The coprocessors operate in ______ with a processor on the same buses and with the same instruction _______. a) Parallel, byte stream. b) Series, byte stream. c) Series, bite stream d) Parallel, bite stream.
Last Answer : a) Parallel, byte stream.
Description : In immediate addressing the operand is placed a. in the CPU register b. after OP code in the instruction c. in memory d. in stack
Last Answer : b. after OP code in the instruction
Description : Any method for controlling access to or use of memory is known a. Memory map b. Memory protection c. Memory management d. Memory instruction
Last Answer : b. Memory protection
Description : What is the control unit's function in the CPU? a. To transfer data to primary storage b. to store program instruction c. to perform logic operations d. to decode program instruction
Last Answer : b. to store program instruction
Description : A compiler is a translating program which a. Translates instruction of a high level language into machine language b. Translates entire source program into machine language program c. It is not involved in program’s execution d. All of above
Last Answer : d. All of above
Description : The subprogram finish the return instruction recovers the return address from the: a. Queue b. Stack c. Program counter d. Pointer
Last Answer : b. Stack
Description : A 32-bit address bus allows access to a memory of capacity(a) 64 Mb (b) 16 Mb (c) 1Gb (d) 4 Gb 2.Which processor structure is pipelined? a) all x80 processors b) all x85 processors c) all x86 processors
Last Answer : c) all x86 processors
Description : The use of spooler programs and/or …. Hardware allows personal computer operators to do the processing work at the same time a printing operation is in progress a. Registered mails b. Memory c. CPU d. Buffer
Last Answer : d. Buffer
Description : A CPU handles interrupt by executing interrupt service subroutine................. (A) by checking interrupt register after execution of each instruction (B) by checking interrupt register ... cycle (C) whenever an interrupt is registered (D) by checking interrupt register at regular time interval
Last Answer : (A) by checking interrupt register after execution of each instruction
Description : Various machine level components are: a. Address register > Program counter c Data register d. Accumulator register e. Memory of 2K,16 bits/word RAM f. Multiplexers g. Allof these
Last Answer : g. Allof these
Description : L2 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these
Last Answer : b. On Mother Board
Description : L1 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these
Last Answer : a. On Processor
Description : A plastic card similar to a credit card but having some memory and a microprocessor embedded within it is a. Punched paper tape b. Chip card c. Card punch
Last Answer : a. Punched paper tape
Description : A is written as separate unit, apart from main and called whenever necessary: a. Subroutine b. Code c. Block d. None of these
Description : Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these
Last Answer : a. Memory unit
Description : A time sharing system imply a. more than one processor in the system b. more than one program in memory c. more than one memory in the system d. None of above
Last Answer : b. more than one program in memory
Description : The first electronic general purpose digital computer built by Motley and Accrete called ENIAC did not work on the stored program concept. How many number s could it store in its internal memory? a. 100 b. 20 c. 40 d. 80
Last Answer : b. 20
Description : What does the disk drive of a computer do? a. Rotate the disk b. Read the disk c. Load a program from the disk into the memory d. Both b and c
Last Answer : d. Both b and c
Description : The first electronic general purpose digital computer built by Mauchly and Eckert called ENIA did not work on the stored program principle. How many numbers could it store in its internal memory? a. 100 b. 20 c. 40 d. 80
Description : Secondary memory can store____: a. Program store code b. Compiler c. Operating system d. All of these
Last Answer : d. All of these
Description : how to make acall from cailf an not be there
Last Answer : Why do you want to lie to your girlfriend?
Description : How does the microprocessor differentiate between data and instruction
Last Answer : When the first m/c code of an instruction is fetched and decoded in the instruction register, the microprocessor recognizes the number of bytes required to fetch the entire ... will be considered as data & the byte after the data will be treated as the next instruction.
Description : Why do we use XRA A instruction
Last Answer : The XRA A instruction is used to clear the contents of the Accumulator and store the value 00H.
Description : Explain the different instruction formats with examples
Last Answer : The instruction set is grouped into the following formats • One byte instruction MOV C,A • Two byte instruction MVI A,39H • Three byte instruction JMP 2345H
Description : Mention the categories of instruction and give two examples for each category
Last Answer : The instructions of 8085 can be categorized into the following five • Data transfer MOV Rd,Rs STA 16-bit • Arithmetic ADD R DCR M • Logical XRI 8-bit RAR • Branching JNZ CALL 16-bit • Machine control HLT NOP
Description : What is an instruction?
Last Answer : An instruction is a binary pattern entered through an input device to command the microprocessor to perform that specific function
Description : Define instruction cycle, machine cycle and T-state
Last Answer : Instruction cycle is defined, as the time required completing theexecution of an instruction. Machine cycle is defined as the time required completing one operation of accessing memory, I/O or ... request. Tcycle is defined as one subdivision of the operation performed in one clock period
Description : Explain the difference between a JMP instruction and CALL instruction.
Last Answer : A JMP instruction permanently changes the program counter. A CALL instruction leaves information on the stack so that the original program execution sequence can be resumed.
Description : How many operations are there in the instruction set of 8085 microprocessor?
Last Answer : There are 74 operations in the 8085 microprocessor.
Description : CISC stands for: a. Complex instruction set computer b. Camper instruct set of computer c. Compared instruction set computer d. None of these
Last Answer : a. Complex instruction set computer
Description : RISC stands for: a. Reduced Instruction set computer b. Reduced Instruct set compare c. Reduced instruction stands computer d. All of these 107. DEC stands for:
Last Answer : a. Reduced Instruction set computer
Description : ISA stands for: a. Instruct set area b. Instruction set architecture c. Both a and b d. None of these
Last Answer : b. Instruction set architecture
Description : Which is not the main feature of DEC Alpha: a. 64 Bit RISC processor b. Designed to replace 32 VAX(CISC) c. Seven stage split integer/floating point pipeline d. Variable Instruction length
Last Answer : d. Variable Instruction length
Description : How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second
Last Answer : a. 2.5 Million instruction per second
Description : Which is most commonly measured in terms of MIPS previously million instruction per second: a. Microprocessor b. Performance of a microprocessor c. Assembly line d. None of thes
Last Answer : b. Performance of a microprocessor