A moving system force in an analog instruments which causes the moving system to deflect from its zero position.

A moving system force in an analog instruments which causes the moving system to
deflect from its zero position.
by

1 Answer

Answer :

deflecting force
by

Related questions

A moving system force in analog instruments which ensures that the deflection of the pointer for a given value of measured quantity always has the same value

Description : A moving system force in analog instruments which ensures that the deflection of the pointer for a given value of measured quantity always has the same value

Last Answer : controlling force

A force in analog instrument which quickly brings the moving system to rest in its final position.

Description : A force in analog instrument which quickly brings the moving system to rest in its final position.

Last Answer : damping force

Which of the following forces does not act on the moving systems of analog instruments?

Description : Which of the following forces does not act on the moving systems of analog instruments?

Last Answer : an electrostatic force

Current range extension in moving coil instruments can be achieved by placing a ___ in shunt with the instrument.

Description : Current range extension in moving coil instruments can be achieved by placing a ___ in shunt with the instrument.

Last Answer : low resistance resistor

The zero-adjust control in an analog type ohmmeter is used to

Description : The zero-adjust control in an analog type ohmmeter is used to

Last Answer : compensate for the differing internal battery voltage

Majority of analog measuring instrument utilizes one of the following effects.

Description : Majority of analog measuring instrument utilizes one of the following effects.

Last Answer : magnetic effect

A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value B. deflect to zero and remain at that position C. swing to a high reading and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Description : A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value ... and gradually decrease D. swing to zero then gradually increase with slight pointer movements down scale

Last Answer : Answer: B

Induction type instruments are mostly used as ___

Description : Induction type instruments are mostly used as ___

Last Answer : watt-hour meter

Electrostatic instruments are exclusively used as

Description : Electrostatic instruments are exclusively used as

Last Answer : voltmeters

Electrostatic instruments are exclusively used as

Description : Electrostatic instruments are exclusively used as

Last Answer : voltmeters

Which electrical instruments below is the most sensitive?

Description : Which electrical instruments below is the most sensitive?

Last Answer : PMMC

Attraction and repulsion instruments are considered

Description : Attraction and repulsion instruments are considered

Last Answer : moving iron instruments

Errors due to frictions of the meter movement, incorrect spring tension, improper calibration or faulty instruments:

Description : Errors due to frictions of the meter movement, incorrect spring tension, improper calibration or faulty instruments:

Last Answer : instrument errors

As the deflection of the moving system increases, the controlling torque in an indicating instrument.

Description : As the deflection of the moving system increases, the controlling torque in an indicating instrument.

Last Answer : increases

A small swamping resistance is connected in series with operating coil of a moving coil ammter in order to compensate for the effects of ____

Description : A small swamping resistance is connected in series with operating coil of a moving coil ammter in order to compensate for the effects of ____

Last Answer : temperature variation

In a moving coil ammeter, a ___ is connected in series with the coil to compensate for temperature variations

Description : In a moving coil ammeter, a ___ is connected in series with the coil to compensate for temperature variations

Last Answer : swamping resistors

Moving-iron instrument has a/an scale

Description : Moving-iron instrument has a/an scale

Last Answer : squared

To increase the measuring capability of a moving-iron ac ammeter, a __ should be used.

Description : To increase the measuring capability of a moving-iron ac ammeter, a __ should be used.

Last Answer : different number of turns of coils

Permanent-magnet moving coil instrument can be used in

Description : Permanent-magnet moving coil instrument can be used in

Last Answer : dc work only

Meters with moving coil are normally used for measuring ____

Description : Meters with moving coil are normally used for measuring ____

Last Answer : dc only

What is the reason why the scale of a permanent-magnet moving coil instrument is uniform?

Description : What is the reason why the scale of a permanent-magnet moving coil instrument is uniform?

Last Answer : because it is spring controlled

What is the typical full-scale voltage across a moving coil voltmeter?

Description : What is the typical full-scale voltage across a moving coil voltmeter?

Last Answer : 50mV

What is the typical full-scale deflection current of a moving coil instrument?

Description : What is the typical full-scale deflection current of a moving coil instrument?

Last Answer : 50mA

When the vertical input is 0V, the electron beam may be position at the __ of the screen.

Description : When the vertical input is 0V, the electron beam may be position at the __ of the screen.

Last Answer : vertical center

How will you check zero of a level D.P. transmitter while is line ?

Description : How will you check zero of a level D.P. transmitter while is line ? 

Last Answer : ١. Close both the isolation valves. ٢. Open the vent valve on L.P. leg and H.P. leg drain. ٣. Check and adjust zero if necessary. 

What is absolute zero pressure ?

Description : What is absolute zero pressure ?

Last Answer : Absolute zero = 760 mm Hg Vacuum.

How do you do a zero check on a D.P. transmitter ?

Description : How do you do a zero check on a D.P. transmitter ?

Last Answer : Close one of the valve either H.P. or L.P. open the equalizing valve. The O/P should read zero.

What is the force acting on the pointer of an indicating instrument when it is in motion?

Description : What is the force acting on the pointer of an indicating instrument when it is in motion?

Last Answer : controlling, damping and deflecting torques

The electric field applied in vertical directional to the cathode rays moving horizontally deflect them in __________

Description : The electric field applied in vertical directional to the cathode rays moving horizontally deflect them in __________

Last Answer : The electric field applied in vertical directional to the cathode rays moving horizontally deflect them in __________ ... a) and (b) D. None of these

A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value for the capacitor B. first swing quickly to 'zero', then gradually move up the scale as the capacitor charges C. immediately deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Description : A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance ... deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Last Answer : Answer: C

What are Intrinsically safe system ?

Description : What are Intrinsically safe system ?

Last Answer : Intrinsic safety is a technique for designing electrical equipment for safe use in locations made hazardous by the presence of flammable gas or vapors in air. "Defn. :" Intrinsically safe circuit is ... , unfortunately, been adopted in all countries. However two sets of codes in common use are.  

What is two wire and three wire R.T.D. system ?

Description : What is two wire and three wire R.T.D. system ?  

Last Answer : Two wire R .T .D. system : Two wire RTD system use for short distance like a compressor field local panel. Three wire System : Three wire system use for long distance coke a field to control Run. The third wire is used for compensation of lead wire resistance. 

What is purge level system ?

Description : What is purge level system ?

Last Answer : This method is also known as bubbler method of level measurement. A pipe is installed vertically with its open end at the zero level. The other end of the pipe is connected to a regulated ... liquids where the transmitter cannot be directly connected to process eg... Acids, Some organic liquids.

In RF and microwave system, what instrument is used to measure the incidental and reflected signals?

Description : In RF and microwave system, what instrument is used to measure the incidental and reflected signals?

Last Answer : reflectometer

Draw block diagram of instrumentation system. State function.

Description : Draw block diagram of instrumentation system. State function.

Last Answer : Primary transducer: The sensor which comes in contact with the measurement medium to sense the quantity. Variable conversion element: the transducer which converts the sensor ... transmitted through suitable transmission medium to the operator or presented with the help of indicators.

What is a thyristor ? What are its uses ?

Description : What is a thyristor ? What are its uses ?

Last Answer : A thyristor is a special kind of semi conductor device that uses internal feedback to produce latching action. Use : Used for controlling large amounts of load power in motors, heaters, lighting systems etc ... the latches like a open switch. This latch will always stay in open or close position.  

What is feed back control ? What is feed forward control ? Discuss its application ?

Description : What is feed back control ? What is feed forward control ? Discuss its application ?

Last Answer : Feed back control: Feed back control involves the detection of the controlled variable and counteracting of charges its it's value relative to set point, by adjustment of a manipulated ... controller for a particular process application, two factors time and gain must be considered.    

Draw a potentiometer temp. Measuring circuits and explain its?

Description : Draw a potentiometer temp. Measuring circuits and explain its?  

Last Answer : OPERATION : The input to the instrument is a measurement of some in the processes using a sensing element ( such as thermocouple ) or a device to produce direct voltage, which is the voltage (signal) ... to zero results ( null point ) the balancing ( servo motor is be longer driven )   

What do you call an oscilloscope that uses sampling techniques in processing signals having frequencies beyond its normal capabilities?

Description : What do you call an oscilloscope that uses sampling techniques in processing signals having frequencies beyond its normal capabilities?

Last Answer : sampling oscilloscope

A meter has a full-scale current of 50uA, what is its sensitivity?

Description : A meter has a full-scale current of 50uA, what is its sensitivity?

Last Answer : Is=1/50uA=20kohm/V

What do you call of an instrument that depends for its operation on the reaction between magnetic flux set up by currents in fixed windings and other currents set up by electromagnet induction in movable conducting parts?

Description : What do you call of an instrument that depends for its operation on the reaction between magnetic flux set up by currents in fixed windings and other currents set up by electromagnet induction in movable conducting parts?

Last Answer : induction instrument

What is that meter that depends for its operation on the forces attraction and repulsion

Description : What is that meter that depends for its operation on the forces attraction and repulsion

Last Answer : electrostatic instrument

A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Description : A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Last Answer : False.

What is a filter used for ?

Description : What is a filter used for ?

Last Answer : The half wave and full wave signals are pulsating D . C . voltages. The use of such voltages is limited to charging batteries, running D. C. motors, and a few other applications. What we really ... voltage from a battery. To get a constant voltage from this, we can use a capacitor input filter. 

What is Zener Diode ? What is a voltage Regulator ?

Description : What is Zener Diode ? What is a voltage Regulator ?

Last Answer : The breakdown region of a p n diode can be made very sharp and almost vertical Diodes with almost vertical breakdown region are known as Zever Diodes. A Zener diodes operating in the breakdown ... VOLTAGE REGULATOR : The output remains constant despite changes in input voltage due to Zever effect.  

What is transistor ? What are the different types ?

Description : What is transistor ? What are the different types ?

Last Answer : A transistor is a three lagged semi conductor device. Basically a transistor means (transfer - resister). Whether the transistor is pnp or npn it resembles two diodes (back to back). The one of the left ... transistor : Emitter - Base - Forward Bias. Collector - Base - Reverse Bias. 

What is CB, CE and CC configuration ?

Description : What is CB, CE and CC configuration ?

Last Answer : Buffer : A device or a circuit used to isolate two pt'ne circuits or stages. The emitter follows is a example of buffer. Alpha = IC / IE Beta = IC / IB

How will you test a transistor with a multimeter. ?

Description : How will you test a transistor with a multimeter. ?

Last Answer : 1. Emitter +ve of meter and Base -ve output = Low resistance 2. Emitter -ve of meter and base +ve output = High resistance. 3. Collector +ve and Base -ve output = Low. 4. Collector -ve and base +ve output = High. Emitter : Collector = High Resistance. PNP : Opposite Results. 

What does a transmitter output start from 3-15 psi or (0.2 - 1 Kg/Cm2) or 4 - 20 ma. etc. ?

Description : What does a transmitter output start from 3-15 psi or (0.2 - 1 Kg/Cm2) or 4 - 20 ma. etc. ? 

Last Answer : The transmitter output stance from what is known as "live zero". This system has specific advantages : 1. The systems automatically alarms when the signal system becomes inoperative. ... transmitter operating, but transmitting a zero measurement and a failure, in the signal system. 

What is Furnace Draft control ?

Description : What is Furnace Draft control ? 

Last Answer : Balanced draft boilers are generally used negative furnace pressure. When both forced draft and induced draft are used together, at some point in the system the pressure will be the same as that of atmosphere. ... have is a very slight (about 0.1" H20 ) negative pressure of the top of furnace.