What is the current rating of a switch?

What is the current rating of a switch?
by

1 Answer

Answer :

The maximum current a switch is designed to carry.
by

Related questions

What is the voltage rating of a switch?

Description : What is the voltage rating of a switch?

Last Answer : The maximum voltage allowable in the circuit in which the switch is installed.

List the four factors you should use to select wire for a specified current rating.

Description : List the four factors you should use to select wire for a specified current rating.

Last Answer : Conductor size, the material it is made of the location of the wiren in a circuit, and the type of insulation used.

What does the current rating of a fuse indicate?

Description : What does the current rating of a fuse indicate?

Last Answer : The amount of current the fuse will allow without opening.

How rating of main switch and cable is selected for Industrial Installation.

Description : How rating of main switch and cable is selected for Industrial Installation.

Last Answer : 1. Rating of Main Switch or Fuse Rating is decided in industrial installation: Rating of main switch or fuse is based up the starting current of motor. For calculating starting current is considered 2 ... take 1.5 times the rated current or full load current. & thus cable rating is decided.

What does the wattage rating of a resistor indicate?

Description : What does the wattage rating of a resistor indicate?

Last Answer : Its ability to dissipate heat

The floppy disks you are using have a rating of 96 TPI. What does this mean?

Description : The floppy disks you are using have a rating of 96 TPI. What does this mean?

Last Answer : The disks can hold 96 tracks per inch.

. If the power distribution system shown in figure 2-22 uses selective tripping, what is the time delay rating for each of the circuit breakers shown?

Description : . If the power distribution system shown in figure 2-22 uses selective tripping, what is the time delay rating for each of the circuit breakers shown?

Last Answer : CB1-long time delay; CB2, CB3-short time delay; CB4 through

What does the voltage rating of a fuse indicate?

Description : What does the voltage rating of a fuse indicate?

Last Answer : The ability of the fuse to quickly extinguish the arc after the fuse element melts and the maximum voltage that cannot jump across the gap of the fuse after the fuse opens.

What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Description : What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Last Answer : It will overheat and could burn the insulation of the wire being soldered.

What type of bias makes a diode act as a closed switch?

Description : What type of bias makes a diode act as a closed switch?

Last Answer : Forward bias.

If the ignition switch is placed in the ON position and all the engine instruments operate properly except the gas gauge, where would the fault probably be?

Description : If the ignition switch is placed in the ON position and all the engine instruments operate properly except the gas gauge, where would the fault probably be?

Last Answer : Between point (3) and the gas gauge tank unit ground.

What device is used to switch power from the normal source to an alternate source for nonvital users?

Description : What device is used to switch power from the normal source to an alternate source for nonvital users?

Last Answer : What device is used to switch power from the normal source to an alternate source for nonvital users?

When cleaning the parts of a tape transport, why should you switch lint-free cloths and swabs often?

Description : When cleaning the parts of a tape transport, why should you switch lint-free cloths and swabs often?

Last Answer : You may transfer dirt or oxide particles from one part of the tape transport to another

If a switch must be checked with power applied, what type of meter is used?

Description : If a switch must be checked with power applied, what type of meter is used?

Last Answer : A voltmeter.

What two types of meters can be used to check a switch?

Description : What two types of meters can be used to check a switch?

Last Answer : An ohmmeter and a voltmeter.

What is the common name used for an accurate snap acting switch?

Description : What is the common name used for an accurate snap acting switch?

Last Answer : A microswitch.

What type of switch is used if it is necessary to guard against a circuit being accidentally turned

Description : What type of switch is used if it is necessary to guard against a circuit being accidentally turned

Last Answer : A locked-position switch.

What type of switch should be used to control a circuit that requires a temporary actuation signal?

Description : What type of switch should be used to control a circuit that requires a temporary actuation signal?

Last Answer : A momentary switch.

In describing a switch by the number of positions of the actuator, what are the two possible configurations for a single pole, double-throw switch?

Description : In describing a switch by the number of positions of the actuator, what are the two possible configurations for a single pole, double-throw switch?

Last Answer : Two-position and three-position.

What classification of a switch is used when you describe it as a rocker switch?

Description : What classification of a switch is used when you describe it as a rocker switch?

Last Answer : The type of actuator.

What is one example of an automatic switch?

Description : What is one example of an automatic switch?

Last Answer : A thermostat, an automobile distributor, a limit switch, etc.

What is one example of a manual switch?

Description : What is one example of a manual switch?

Last Answer : A light switch, an ignition switch, television channel selector, etc.

What is the difference between a manual and an automatic switch?

Description : What is the difference between a manual and an automatic switch?

Last Answer : A manual switch must be turned on or off by a person. An automatic switch turns a circuit on or off without the action of a person

2. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. -Physics-10

Description : 2. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. -Physics-10

Last Answer : The current drawn by the electric oven can be calculated using the formula P = V × I I = P/V Substituting the values, we get I = 2000 W/220 V = 9.09 A The current drawn by the electric oven is 9.09 A which exceeds the safe limit of the circuit. This causes the fuse to melt and break the circuit.

Are there services online to help me find my current credit score rating?

Description : Are there services online to help me find my current credit score rating?

Last Answer : There are services online to help you find your current credit score rating. You can go to MyFico.com or www.experian.com/credit-education/basics.html.

A graphing calculator uses a 6.0 V battery and draws 2.6 × 10−3 A of current. What is the power rating of the calculator?

Description : A graphing calculator uses a 6.0 V battery and draws 2.6 × 10−3 A of current. What is the power rating of the calculator?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Description : Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Last Answer : Answer: A

Which of the following statements about copper wire sized by the AWG rating is correct? A. Number 12 AWG wire has a higher current rating than number 10 AWG wire. B. Number 10 AWG wire has a higher dielectric strength than number 12 AWG wire. C. Number 12 AWG wire is larger than Number 10 AWG wire. D. Number 12 AWG wire at 25°C has more resistance per 1000 feet than No. 10 AWG wire at 25°C.

Description : Which of the following statements about copper wire sized by the AWG rating is correct? A. Number 12 AWG wire has a higher current rating than number 10 AWG wire. B. Number 10 AWG wire has a higher ... Number 12 AWG wire at 25°C has more resistance per 1000 feet than No. 10 AWG wire at 25°C.

Last Answer : Answer: D

Which of the following statements concerning copper wire sized by AWG numbers is correct? A. Number 12 AWG wire has a higher current rating than 10 AWG wire. B. Number 12 AWG wire at 25°C has more resistance per 1000 ft than 10 AWG wire at 25°C. C. Number 10 AWG wire has a higher dielectric strength than 12 AWG wire. D. Number 12 AWG wire is larger than number 10 AWG wire.

Description : Which of the following statements concerning copper wire sized by AWG numbers is correct? A. Number 12 AWG wire has a higher current rating than 10 AWG wire. B. Number 12 AWG wire at 25°C has more ... dielectric strength than 12 AWG wire. D. Number 12 AWG wire is larger than number 10 AWG wire.

Last Answer : Answer: B

Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Description : Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Last Answer : Answer: C

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Description : A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Last Answer : Answer: A

Define the followings. Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Description : Define the followings.   Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Last Answer : Insulation level - it is the combination of rated voltage, the corresponding impulse withstand voltage, which together characterize the insulation of the equipment as regards its ability to withstand ... wave of power frequency (50 Hz) which the insulation of equipment should withstand. 

To determine the discharge at a section in a stream from its rating curve, the required data are (i) Slope of water surface at the section (ii) Stage at the section (ii) Current meter readings at the section The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) Only (ii) (D) Only (iii)

Description : To determine the discharge at a section in a stream from its rating curve, the required data are (i) Slope of water surface at the section (ii) Stage at the section (ii) Current meter readings at the section The correct ... ) (i) and (ii) (B) (ii) and (iii) (C) Only (ii) (D) Only (iii)

Last Answer : Answer: Option C

The capacity of a battery is expressed in terms of A. Current rating B. Voltage rating C. Ampere hour rating D. None of the above

Description : The capacity of a battery is expressed in terms of A. Current rating B. Voltage rating C. Ampere hour rating D. None of the above

Last Answer : C. Ampere hour rating

A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Description : A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Last Answer : False.

Which of the following will give your company an AAA bond rating: a. Have contribution margins higher than 30%. b. Have absolutely no debt. c. Retire all of the current outstand stock. d. Pay a dividend that is less than EPS. e. Retire bonds before they are due.

Description : Which of the following will give your company an AAA bond rating: a. Have contribution margins higher than 30%. b. Have absolutely no debt. c. Retire all of the current outstand stock. d. Pay a dividend that is less than EPS. e. Retire bonds before they are due.

Last Answer : b. Have absolutely no debt.

What is your bond rate? The prime rate is 10%; your current bond rating slipped one category (from AAA to AA). a. 12.1% b. 10.5% c. 11.4% d. 11.2%

Description : What is your bond rate? The prime rate is 10%; your current bond rating slipped one category (from AAA to AA). a. 12.1% b. 10.5% c. 11.4% d. 11.2%

Last Answer : b. 10.5%

47 Cross over windings are used in A. Low voltage side of high kVA rating transformers B. Current transformers C. High voltage side of high kVA rating transformers D. High voltage side of low kVA rating transformers

Description : 47 Cross over windings are used in A. Low voltage side of high kVA rating transformers B. Current transformers C. High voltage side of high kVA rating transformers D. High voltage side of low kVA rating transformers

Last Answer : D. High voltage side of low kVA rating transformers

The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Description : The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Last Answer : (d) upto 80 A

By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Last Answer : (e) All of the above.

Define the following terms related to circuit breaker. 1) Breaking Capacity 2) Making Capacity 3) Short time rating and 4) Normal current rating

Description : Define the following terms related to circuit breaker. 1) Breaking Capacity 2) Making Capacity 3) Short time rating and 4) Normal current rating

Last Answer : 1) Breaking Capacity: It is current (r.m.s) that a circuit breaker is capable of breaking at given recovery voltage under specified conditions (e.g. power factor, rate of rise of ... under specified conditions. The only limitation in this case is the temperature rise of current-carrying parts.

Surge current rating of an SCR specifies the maximum

Description : Surge current rating of an SCR specifies the maximum  (a) Repetitive current with sine wave (b) Non-repetitive current with sine wave (c) Non-repetitive current with rectangular wave (d) Repetitive current with rectangular wave  

Last Answer : Surge current rating of an SCR specifies the maximum Non-repetitive current with sine wave

The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :

Description : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

Last Answer : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be : 34.64 kVA

What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp?

Description : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

Last Answer : What is the line current of a circuit when the current transformer of 1000 : 5 rating measures 4 amp? (A) 5000 amp (B) 1000 amp (C) 400 amp (D) 800 amp 

The kVA rating required for a transformer that must handle a maximum load current of 8 A with a ...

Description : The kVA rating required for a transformer that must handle a maximum load current of 8 A with a secondary voltage of 2 kV will be: A. 4 kVA B. 0.25 kVA C. 16 kVA D. 8 kVA

Last Answer : The kVA rating required for a transformer that must handle a maximum load current of 8 A with a secondary voltage of 2 kV will be: 16 kVA

What are current solutions to switch to Internet-based TV and movies (see details)?

Description : What are current solutions to switch to Internet-based TV and movies (see details)?

Last Answer : answer:I can only speak for Netflix. Either get a Netflix box. OR an XBox (I have that). Pumping the signal our of the PC works, but can be a bit of a pain. And the more bandwith the better the stream.

As the switch `S` is closed in the circuit shown in figure, current passed through it is.

Description : As the switch `S` is closed in the circuit shown in figure, current passed through it is.

Last Answer : As the switch `S` is closed in the circuit shown in figure, current passed through it is. A. `4.5A` B. `6.0A` C. `3.0A` D. zero