If the ignition switch is placed in the ON position and all the engine instruments operate properly except the gas gauge, where would the fault probably be?

If the ignition  switch is placed in the ON position and all the engine  instruments operate properly except the gas gauge, where  would the fault probably be?
by

1 Answer

Answer :

Between point (3) and the gas gauge tank unit ground.
by

Related questions

Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle

Last Answer : ANSWER : A

Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Description : Use of gasoline blend like tetraethyl lead in internal combustion engine a. increases the octane rating of the fuel b. allows engine to operate at higher compression ratio c. avoids auto-ignition of fuel d. all of the above

Last Answer : ANSWER d. all of the above

Is it possible for a transmission line to operate improperly at certain frequencies and properly at others?

Description : Is it possible for a transmission line to operate improperly at certain frequencies and properly at others?

Last Answer : Yes, it is quite common.

The violent noises heard in an engine during the process of combustion after the position has passed over the top dead center is known as? 1. Stationary 2. Spark ignition 3. Detonation 4. all of these

Description : The violent noises heard in an engine during the process of combustion after the position has passed over the top dead center is known as? 1. Stationary 2. Spark ignition 3. Detonation 4. all of these

Last Answer :     <!-- [endif] -->ans 3

Prior to starting an AC generator prime mover, the voltage regulator cutout switch should be placed in the __________. A. manual position B. bus neutral position C. raise voltage position D. transfer position

Description : Prior to starting an AC generator prime mover, the voltage regulator cutout switch should be placed in the __________. A. manual position B. bus neutral position C. raise voltage position D. transfer position

Last Answer : Answer: A

In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Description : In a typical velocity servo block diagram what device is placed in the feedback loop that is not present in the position servo?

Last Answer : Tachometer.

If a free gyro is placed at the equator at 1200 in a vertical position; in what position should it be at 1800?

Description : If a free gyro is placed at the equator at 1200 in a vertical position; in what position should it be at 1800?

Last Answer : Horizontal.

how do I disconnect the wires from a 1999 dodge ram 2500 clutch safety ignition switch?

Description : how do I disconnect the wires from a 1999 dodge ram 2500 clutch safety ignition switch?

Last Answer : Need Answer

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Last Answer : Answer: B

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Last Answer : Answer: B

Which of the following terms is used to describe inability to breathe easily except in an upright position? a) Orthopnea Patients with orthopnea are placed in a high Fowler’s position to facilitate breathing. b) Dyspnea Dyspnea refers to labored breathing or shortness of breath. c) Hemoptysis Hemoptysis refers to expectoration of blood from the respiratory tract. d) Hypoxemia Hypoxemia refers to low oxygen levels in the blood.

Description : Which of the following terms is used to describe inability to breathe easily except in an upright position? a) Orthopnea Patients with orthopnea are placed in a high Fowler's position to facilitate ... blood from the respiratory tract. d) Hypoxemia Hypoxemia refers to low oxygen levels in the blood.

Last Answer : a) Orthopnea Patients with orthopnea are placed in a high Fowler’s position to facilitate breathing.

The longer a fault exists in a) the more tedious its removal becomes b) the more costly it is to detect and correct c) the less likely it is to be properly corrected d) All of the mentioned

Description : The longer a fault exists in a) the more tedious its removal becomes b) the more costly it is to detect and correct c) the less likely it is to be properly corrected d) All of the mentioned

Last Answer : d) All of the mentioned

What are the fault-finding techniques to be used if the equipment fails to operate correctly?

Description : What are the fault-finding techniques to be used if the equipment fails to operate correctly?

Last Answer : 1. Pin point the problem - what is not happening asexpected.2. Read the error messages, error codes if any from theequipment.3. Refer the manual for troubleshooting points follow the stepsprovided.4. Talk to the expert and explain the problem and inform theobserved behavior of the equipment.

What are the fault-finding techniques to be used if the equipment fails to operate correctly?

Description : What are the fault-finding techniques to be used if the equipment fails to operate correctly?

Last Answer : 1. Pin point the problem - what is not happening asexpected.2. Read the error messages, error codes if any from theequipment.3. Refer the manual for troubleshooting points follow the stepsprovided.4. Talk to the expert and explain the problem and inform theobserved behavior of the equipment.

Will rotor earth fault relay operate for earth fault in main exciter winding or RCU Diode Bridge also?

Description : Will rotor earth fault relay operate for earth fault in main exciter winding or RCU Diode Bridge also? 

Last Answer : Yes. 

Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Description : Which of the following statements is incorrect? (a) Station batteries are used to operate relay only (b) The lightning arresters are basically surge diverters (c) An impedance relay has maximum fault current when fault occurs near the relay (d) A high speed relay has an operation of 1 to 2 cycles

Last Answer : (a) Station batteries are used to operate relay only

If a relay fails to operate for a fault within its reach, it is said to

Description : If a relay fails to operate for a fault within its reach, it is said to

Last Answer : If a relay fails to operate for a fault within its reach, it is said to Under reach

The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All (a) to (c)

Description : The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All (a) to (c)

Last Answer :  All (a) to (c)

25. The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All (a) to (c)

Description : The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All (a) to (c)

Last Answer :  All (a) to (c)

18. The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All above

Description : The various types of the instruments, which requires during audit need to be a) Easy to carry b) Easy to operate c) Inexpensive d) All above

Last Answer : all of the above

The various types of instruments required during audit is not need to be…. a) Easy to carry b) Inexpensive c) Easy to operate d) Unreadable

Description : The various types of instruments required during audit is not need to be…. a) Easy to carry b) Inexpensive c) Easy to operate d) Unreadable

Last Answer : Unreadable

Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Description : Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Last Answer : ∙ B. reverse bias

Photodiodes operate properly with:

Description : Photodiodes operate properly with:

Last Answer : reverse bias

What is the function of watchdog timer? a) The watchdog Timer is an external timer that resets the system if the software fails to operate properly. b) The watchdog Timer is an internal timer that sets the system if the software fails to operate properly. c) The watchdog Timer is an internal timer that resets the system if the software fails to operate properly. d) None of them

Description : What is the function of watchdog timer? a) The watchdog Timer is an external timer that resets the system if the software fails to operate properly. b) The watchdog Timer is an internal timer ... internal timer that resets the system if the software fails to operate properly. d) None of them

Last Answer : b) The watchdog Timer is an internal timer that sets the system if the software fails to operate properly.

What is the function of watchdog timer? a) The watchdog Timer is an external timer that resets the system if the software fails to operate properly. b) The watchdog Timer is an internal timer that sets the system if the software fails to operate properly. c) The watchdog Timer is an internal timer that resets the system if the software fails to operate properly. d) None of them

Description : What is the function of watchdog timer? a) The watchdog Timer is an external timer that resets the system if the software fails to operate properly. b) The watchdog Timer is an internal timer ... internal timer that resets the system if the software fails to operate properly. d) None of them

Last Answer : c) The watchdog Timer is an internal timer that resets the system if the software fails to operate properly.

A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem probably lies in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem ... in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow speed and half speed. The problem probably lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow ... lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: d Explanation: The knock sensor,is a microphone type sensor that detects ping or pre-ignition noise so that the ignition timing can be retarded while the camshaft position sensor, senses ... the engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 volts were applied to the 'setpoint module' B. 'reduction gear lube oil pressure' fell below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Description : An open-circuit fault between the pressure switch and the 'annunciator module' shown in the illustration would cause the alarm circuit to react in the same manner as if ___________. EL-0094 A. 3.5 ... below switch setting C. 50 PSI were applied to the 'setpoint module' D. the pressure switch closed

Last Answer : Answer: B

. Consider the above state transition diagram of a switch.Which of the following represents an invalid state transition? a) OFF to ON b) ON to OFF c) FAULT to ON Q15. Peer Reviews are also called as :- a) Inspection b) Walkthrough

Description : . Consider the above state transition diagram of a switch.Which of the following represents an invalid state transition? a) OFF to ON b) ON to OFF c) FAULT to ON Q15. Peer Reviews are also called as :- a) Inspection b) Walkthrough

Last Answer : c) FAULT to ON

What is the purpose of the earth fault indication on the switch board?

Description : What is the purpose of the earth fault indication on the switch board?

Last Answer : It detects and indicates phase to earth fault on a circuit.

What causes ignition to occur in a diesel engine?

Description : What causes ignition to occur in a diesel engine?

Last Answer : When the piston compresses the fuel-air mixture, the spark ignites it, causing combustion

The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period

Description : The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period

Last Answer : ANSWER : A

In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Description : In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed

Last Answer : ANSWER : C

Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Last Answer : ANSWER : C

In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)

The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Description : The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Last Answer : Which of the following is not true for two stroke engine as compared to four stroke engine? a. Less cooling is required b. Greater lubrication is required c. More uniform torque on crankshaft d. Complete exhaust of products of combustion (Ans:a)

The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Description : The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure

Last Answer : Ans :c

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Last Answer : ANSWER c. Both a and b.

Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Description : Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Last Answer : ANSWER b. compression ignition engine

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Last Answer : ANSWER c. Both a and b

Combustion in compression ignition engine is a. homogeneous b. heterogeneous c. laminar d. turbulent

Description : Combustion in compression ignition engine is a. homogeneous b. heterogeneous c. laminar d. turbulent

Last Answer : ANSWER b. heterogeneous

For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Description : For spark ignition engine, the equivalence ratio of mixture entering the combustion chamber has values (A) for idling and for peak power conditions (B) for both idling and peak power conditions (C) for idling and for peak power conditions (D) for both idling and peak power conditions

Last Answer : ANSWER (B) for both idling and peak power conditions

A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel cycle is higher than the Otto cycle, at a fixed compression ratio c. The compression ratio of a diesel engine is higher than that of an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Description : A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel ... an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Last Answer : ANSWER c. The compression ratio of a diesel engine is higher than that of an S.I engine

Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Description : Rate of burning in the compression ignition engine can be controlled by a. rate of injection of fuel b. rate of air taken into carburetor c. both a. and b. d. none of the above

Last Answer : ANSWER a. rate of injection of fuel

The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Description : The compression ratio cannot be increased beyond certain limit as it results in a. auto-ignition of fuel b. detonation c. engine knocking d. all the above

Last Answer : ANSWER d. all the above

Which of the following cycle is used for Compression Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : Which of the following cycle is used for Compression Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer b. Diesel cycle

Which of the following cycle is used for Spark Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : Which of the following cycle is used for Spark Ignition engine? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer a. Otto cycle

Spark plug is provided in a/an (A) Engine having carburettor (B) Diesel engine (C) Compression ignition engine (D) Both (B) & (C)

Description : Spark plug is provided in a/an (A) Engine having carburettor (B) Diesel engine (C) Compression ignition engine (D) Both (B) & (C)

Last Answer : (A) Engine having carburettor