What is the voltage rating of a switch?

What is the voltage rating of a switch?
by

1 Answer

Answer :

The maximum voltage allowable in the circuit in which the switch  is installed.
by

Related questions

What is the current rating of a switch?

Description : What is the current rating of a switch?

Last Answer : The maximum current a switch is designed to carry.

What does the voltage rating of a fuse indicate?

Description : What does the voltage rating of a fuse indicate?

Last Answer : The ability of the fuse to quickly extinguish the arc after the fuse element melts and the maximum voltage that cannot jump across the gap of the fuse after the fuse opens.

How rating of main switch and cable is selected for Industrial Installation.

Description : How rating of main switch and cable is selected for Industrial Installation.

Last Answer : 1. Rating of Main Switch or Fuse Rating is decided in industrial installation: Rating of main switch or fuse is based up the starting current of motor. For calculating starting current is considered 2 ... take 1.5 times the rated current or full load current. & thus cable rating is decided.

What does the wattage rating of a resistor indicate?

Description : What does the wattage rating of a resistor indicate?

Last Answer : Its ability to dissipate heat

The floppy disks you are using have a rating of 96 TPI. What does this mean?

Description : The floppy disks you are using have a rating of 96 TPI. What does this mean?

Last Answer : The disks can hold 96 tracks per inch.

List the four factors you should use to select wire for a specified current rating.

Description : List the four factors you should use to select wire for a specified current rating.

Last Answer : Conductor size, the material it is made of the location of the wiren in a circuit, and the type of insulation used.

. If the power distribution system shown in figure 2-22 uses selective tripping, what is the time delay rating for each of the circuit breakers shown?

Description : . If the power distribution system shown in figure 2-22 uses selective tripping, what is the time delay rating for each of the circuit breakers shown?

Last Answer : CB1-long time delay; CB2, CB3-short time delay; CB4 through

What does the current rating of a fuse indicate?

Description : What does the current rating of a fuse indicate?

Last Answer : The amount of current the fuse will allow without opening.

What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Description : What happens if a soldering gun switch is pressed for periods longer than 30 seconds?

Last Answer : It will overheat and could burn the insulation of the wire being soldered.

What type of bias makes a diode act as a closed switch?

Description : What type of bias makes a diode act as a closed switch?

Last Answer : Forward bias.

If the ignition switch is placed in the ON position and all the engine instruments operate properly except the gas gauge, where would the fault probably be?

Description : If the ignition switch is placed in the ON position and all the engine instruments operate properly except the gas gauge, where would the fault probably be?

Last Answer : Between point (3) and the gas gauge tank unit ground.

What device is used to switch power from the normal source to an alternate source for nonvital users?

Description : What device is used to switch power from the normal source to an alternate source for nonvital users?

Last Answer : What device is used to switch power from the normal source to an alternate source for nonvital users?

When cleaning the parts of a tape transport, why should you switch lint-free cloths and swabs often?

Description : When cleaning the parts of a tape transport, why should you switch lint-free cloths and swabs often?

Last Answer : You may transfer dirt or oxide particles from one part of the tape transport to another

If a switch must be checked with power applied, what type of meter is used?

Description : If a switch must be checked with power applied, what type of meter is used?

Last Answer : A voltmeter.

What two types of meters can be used to check a switch?

Description : What two types of meters can be used to check a switch?

Last Answer : An ohmmeter and a voltmeter.

What is the common name used for an accurate snap acting switch?

Description : What is the common name used for an accurate snap acting switch?

Last Answer : A microswitch.

What type of switch is used if it is necessary to guard against a circuit being accidentally turned

Description : What type of switch is used if it is necessary to guard against a circuit being accidentally turned

Last Answer : A locked-position switch.

What type of switch should be used to control a circuit that requires a temporary actuation signal?

Description : What type of switch should be used to control a circuit that requires a temporary actuation signal?

Last Answer : A momentary switch.

In describing a switch by the number of positions of the actuator, what are the two possible configurations for a single pole, double-throw switch?

Description : In describing a switch by the number of positions of the actuator, what are the two possible configurations for a single pole, double-throw switch?

Last Answer : Two-position and three-position.

What classification of a switch is used when you describe it as a rocker switch?

Description : What classification of a switch is used when you describe it as a rocker switch?

Last Answer : The type of actuator.

What is one example of an automatic switch?

Description : What is one example of an automatic switch?

Last Answer : A thermostat, an automobile distributor, a limit switch, etc.

What is one example of a manual switch?

Description : What is one example of a manual switch?

Last Answer : A light switch, an ignition switch, television channel selector, etc.

What is the difference between a manual and an automatic switch?

Description : What is the difference between a manual and an automatic switch?

Last Answer : A manual switch must be turned on or off by a person. An automatic switch turns a circuit on or off without the action of a person

What is the voltage rating of the capacitor ?

Description : What is the voltage rating of the capacitor ?

Last Answer : : The maximum voltage that the capacitor operates is called the voltage rating of the capacitor. This voltage rating of the capacitor is expressed by the letter V.

What is the voltage in a 30 and Omega circuit with a power rating of 480W?

Description : What is the voltage in a 30 and Omega circuit with a power rating of 480W?

Last Answer : Need answer

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Description : If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Last Answer : Answer: C

AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Description : AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Last Answer : Answer: A

Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Description : Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit? A. voltage rating B. weight per unit length C. current rating D. inductance per unit length

Last Answer : Answer: C

A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Description : A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Last Answer : Answer: A

Define the followings. Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Description : Define the followings.   Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Last Answer : Insulation level - it is the combination of rated voltage, the corresponding impulse withstand voltage, which together characterize the insulation of the equipment as regards its ability to withstand ... wave of power frequency (50 Hz) which the insulation of equipment should withstand. 

On what factor voltage rating of the capacitor depend?

Description : On what factor voltage rating of the capacitor depend?  

Last Answer : The voltage rating of the capacitor depends on the distance between the plates of the capacitor. If the voltage exceeds, the electrons across the space between the plates can result in permanent damage to the capacitor. 

If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Description : If 200w, 100 w and 60 w lamps connected in series with 230V AC , which lamp glow brighter? Each lamp voltage rating is 230V.

Last Answer :  Each bulb when independently working will have currents (W/V= I)  For 200 Watt Bulb current (I200) =200/230=0.8696 A  For 100 Watt Bulb current (I100) =100/230=0.4348 A  ... current through it. So minimum power dissipated across it as min current X equal Voltage across =s min power dissipation

The voltage of a capacitor 12F with a rating of 2J energy is a) 0.57 b) 5.7 c) 57 d) 570

Description : The voltage of a capacitor 12F with a rating of 2J energy is a) 0.57 b) 5.7 c) 57 d) 570

Last Answer : a) 0.57

The capacity of a battery is expressed in terms of A. Current rating B. Voltage rating C. Ampere hour rating D. None of the above

Description : The capacity of a battery is expressed in terms of A. Current rating B. Voltage rating C. Ampere hour rating D. None of the above

Last Answer : C. Ampere hour rating

54] In operating a 400hz transformer at 50Hz A. Only voltage is reduced in the same proportion as the frequency B. Only KVA rating is reduced in the same proportion as the frequency C. Both voltage and KVA rating are reduced in the same proportion as frequency d. None of the above

Description : 4] In operating a 400hz transformer at 50Hz A. Only voltage is reduced in the same proportion as the frequency B. Only KVA rating is reduced in the same proportion as the frequency C. Both voltage and KVA rating are reduced in the same proportion as frequency D. None of the above

Last Answer : B. Only KVA rating is reduced in the same proportion as the frequency

47 Cross over windings are used in A. Low voltage side of high kVA rating transformers B. Current transformers C. High voltage side of high kVA rating transformers D. High voltage side of low kVA rating transformers

Description : 47 Cross over windings are used in A. Low voltage side of high kVA rating transformers B. Current transformers C. High voltage side of high kVA rating transformers D. High voltage side of low kVA rating transformers

Last Answer : D. High voltage side of low kVA rating transformers

4 Helical coils can be used on A. Low voltage side of high kVA transformers B. High frequency transformers C. High voltage side of small capacity transformers D. High voltage side of high kVA rating transformers

Description : 4 Helical coils can be used on A. Low voltage side of high kVA transformers B. High frequency transformers C. High voltage side of small capacity transformers D. High voltage side of high kVA rating transformers

Last Answer : A) low voltage side of high KVA transformer

The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :

Description : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

Last Answer : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be : 34.64 kVA

To measure insulation resistance of equipments of voltage rating upto 440 V the megger generator must generate...

Description : To measure insulation resistance of equipments of voltage rating upto 440 V the megger generator must generate   (a) 220 V (b) 440 V (c) 500 V (d) None of these 

Last Answer : 500 V

A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. A. the dark lamp must be replaced B. there is a ground in the line with the dark lamp C. there are grounds in two of the three phases D. the voltage to the dark lamp is less than that of the system

Description : A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. ... of the three phases D. the voltage to the dark lamp is less than that of the system

Last Answer : Answer: A

In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a slight ground on all three phases B. the switch must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Description : In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a ... must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Last Answer : Answer: C

In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL-0007 A. the control fuse is the wrong amperage not allowing full current to pass through B. the stop switch is open C. an open in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Last Answer : Answer: B

A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Description : A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above

Last Answer : Answer: D

When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic position B. adjusted with the voltage regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Description : When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic ... regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Last Answer : Answer: C

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

If reading the AC voltage from the line lead of a 440 VAC controller the range switch illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. Unable to safely read with this meter.

Description : If reading the AC voltage from the line lead of a 440 VAC controller the range switch illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. Unable to safely read with this meter.

Last Answer : Answer: A

If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Description : If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Last Answer : Answer: B