Description : What method is used to allow a voltmeter to have several ranges?
Last Answer : The use of resistors in series with the meter movement.
Description : When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?
Last Answer : A leaking transistor
Description : When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?
Last Answer : Normal gain.
Description : What are two transistor tests that can be done with an ohmmeter?
Last Answer : Gain and junction resistance.
Description : What must be done to a circuit before you can use an ohmmeter for testing?
Last Answer : It must be de-energized.
Description : When checking a diode with an ohmmeter, what is indicated by two high resistance measurements?
Last Answer : The diode is open or has a high-forward resistance.
Description : When testing an SCR with an ohmmeter, the SCR will conduct if what two elements are shorted together?
Last Answer : Gate and anode.
Description : When you are using an ohmmeter to test a transistor, what range settings should be avoided?
Last Answer : Any range setting that produces a current flow through the transistor that exceeds 1 milliamp (usually R x 1 range)
Description : Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?
Last Answer : De-energized
Description : How could you check a 1/500-ampere fuse with an ohmmeter?
Last Answer : Use a resistor in series with the fuse when you check it with the ohmmeter.
Description : You have just checked a 1/500-ampere fuse with an ohmmeter and find it is open. Checking the replacement fuse shows the replacement fuse is open also. Why would the replacement fuse indicate open?
Last Answer : The ohmmeter causes more than 1/500 ampere through the fuse when you check the fuse, thus it opens the fuse.
Description : You have just checked a fuse with an ohmmeter and find that the fuse is shorted. What should you
Last Answer : Put it back in the circuit. A good fuse will have zero ohms of resistance.
Description : What area of an ohmmeter scale should be used when measuring circuits?
Last Answer : The middle of the scale.
Description : How is a series-type ohmmeter connected to the circuit being measured?
Last Answer : The ohmmeter is connected in series with the resistance to be measured.
Description : What other measurement can an ohmmeter make?
Last Answer : Circuit continuity.
Description : What electrical quantity is measured by an ohmmeter?
Last Answer : Resistance.
Description : The R x 100 resistance selection on an ohmmeter has what amount of resistance compared to the R x 10 selection?
Last Answer : 1/10.
Description : . A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?
Last Answer : Zero.
Description : A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?
Description : What six types of environmental damage can occur to tapes in storage when the ideal temperature and humidity ranges are exceeded?
Last Answer : Tape deformation, oxide shedding, head-to-tape sticking, layer to-layer sticking, dirt build-up, and excessive tape and head wear.
Description : Environmental damage to magnetic tape can occur when the tape is stored in an area that exceeds what ideal temperature and humidity ranges?
Last Answer : Ideally, use and store tape at 60 to 80ยบ F and at 40 to 60% relative humidity.
Description : Besides setting up the meter for expected voltage ranges, what must be strictly observed when taking dc voltage readings?
Last Answer : Polarit
Description : What is used to allow an ammeter to measure different ranges?
Last Answer : Shunt resistors (internal or external).
Description : What was the purpose of several computer manufacturers cooperating to develop ASCII code for processing and transmitting data?
Last Answer : To standardize a binary code to give the computer user the capability of using several machines to process data regardless of the manufacturer.
Description : In 1969, what did several scientists conclude about optical fiber loss?
Last Answer : mpurities in the fiber material caused the signal loss in optical fibers. The basic fiber material did not prevent the light signal from reaching the end of the fiber.
Description : Answer: e The role of nutritional support in the cancer patient remains an important component of overall therapy. Preoperative nutritional support should be given only to those patients who ... of bowel rest; this atrophy is not reversed by currently available total parenteral nutrition solutions
Last Answer : Which of the following hormones can be expected to be released as part of the stress response? a. Antidiuretic hormone (ADH) b. Aldosterone c. Insulin d. Epinephrine nswer: a, b, d ... This hormone has the exact opposite effect of insulin, which promotes glucose storage and uptake by the cells
Description : Walton Food Products decided to use agents to reach industrial accounts several years ago. Logically, this decision was based on which one of the following? A)Steady demand for the firm's ... C)Walton's desire to reduce selling costs D)The willingness of agents to provide market information
Last Answer : C)Walton's desire to reduce selling costs
Description : Which of the following is/are correct with reference to Abstract class and interface ? (a) A class can inherit only one Abstract class but may inherit several interfaces. (b) An Abstract class can provide complete and default ... true (C) Both (a) and (b) are true (D) Neither (a) nor (b) is true
Last Answer : Answer: C
Description : What is an ohmmeter ?
Last Answer : : An ohmmeter is a conductive resistor. This determines the amount or resistance of any conductor.
Description : What are the advantage of ohmmeter?
Last Answer : Need answer
Description : When checked with an ohmmeter how should a properly functioning capacitor respond?
Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. millivolt meter and a jumper B. ohmmeter C. megohm meter D. high potential tester
Last Answer : Answer: A
Description : On some electrical generating equipment one outboard bearing pedestal is insulated from the bedplate. To check this insulation with the machine assembled you should use a____________. A. ohmmeter with the ... C. megohm meter with the machine running D. voltmeter and ampmeter with the machine running
Last Answer : Answer: B
Description : Conductor resistance may be INDIRECTLY measured by using a/an _____________. A. voltmeter only B. ammeter only C. voltmeter and an ammeter D. ohmmeter only
Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit
Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding
Description : When troubleshooting a console circuit card suspected of being faulty, first check for proper voltages to the card and then _______________. A. test transistors or integrated circuits for gain and ... D. de-energize the card and check the printed circuit traces for continuity with an ohmmeter
Description : The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the ... in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil
Last Answer : Answer: D
Description : The charge of a lead-acid battery is checked with a _____________. A. manometer B. hydrometer C. viscosimeter D. ohmmeter
Description : Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter
Description : To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter
Description : An ohmmeter used to test for front-to-back resistance of a PN junction diode should produce roughly what ratio? A. 100:01:00 B. 500:01:00 C. 1000:01:00 D. 5000:01:00
Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted
Description : The charge of a lead-acid battery is checked with a/an ____________. A. manometer B. hydrometer C. voltmeter D. ohmmeter
Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter
Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality
Description : Which of the meters listed should only be used after a circuit has been electrically disconnected? A. Wattmeter B. Frequency meter C. Ammeter D. Ohmmeter
Description : An ohmmeter can be used to measure ____________. A. current flow in a circuit B. voltage between two points in a circuit C. circuit continuity D. power
Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity