When testing an SCR with an ohmmeter, the SCR will conduct if what two elements are shorted together?

When testing an SCR with an ohmmeter, the SCR will  conduct if what two elements are shorted together?
by

1 Answer

Answer :

Gate and anode.
by

Related questions

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Description : When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Last Answer : A leaking transistor

You have just checked a fuse with an ohmmeter and find that the fuse is shorted. What should you

Description : You have just checked a fuse with an ohmmeter and find that the fuse is shorted. What should you

Last Answer : Put it back in the circuit. A good fuse will have zero ohms of resistance.

Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be returned to 'zero' on the scale? A. The lead clips should be replaced. B. The batteries should be replaced. C. The test reading should be added to each final reading. D. The test reading should be subtracted from each final reading.

Description : Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be ... be added to each final reading. D. The test reading should be subtracted from each final reading.

Last Answer : Answer: B

When an SCR is forward biased, what is needed to cause it to conduct?

Description : When an SCR is forward biased, what is needed to cause it to conduct?

Last Answer : A gate signal.

When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown control fuse C. a reading of 'zero' on a megger from one of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Last Answer : Answer: B

A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance value for the capacitor B. first swing quickly to 'zero', then gradually move up the scale as the capacitor charges C. immediately deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Description : A capacitor can be tested using a megohmmeter or an ohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should _____________. A. immediately swing to the maximum resistance ... deflect to and remain at zero D. immediately swing to a high reading and then gradually decrease

Last Answer : Answer: C

When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Description : When you are testing the gain of an audio-frequency transistor with an ohmmeter, what is indicated by a 10-to-1 resistance ratio?

Last Answer : Normal gain.

What must be done to a circuit before you can use an ohmmeter for testing?

Description : What must be done to a circuit before you can use an ohmmeter for testing?

Last Answer : It must be de-energized.

To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Description : To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Last Answer : Answer: A

A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. A. a loud growling noise will be heard B. any vibration within the feeler will cease C. the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Description : A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. ... . the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Last Answer : Answer: A

When you zero a synchro with a synchro tester, what is indicated by a jump in the synchro tester's dial when the S1 and S3 leads are momentarily shorted?

Description : When you zero a synchro with a synchro tester, what is indicated by a jump in the synchro tester's dial when the S1 and S3 leads are momentarily shorted?

Last Answer : The synchro under test is not on electrical zero.

If one branch of a parallel network is shorted, what portion of circuit current flows through the remaining branches?

Description : If one branch of a parallel network is shorted, what portion of circuit current flows through the remaining branches?

Last Answer : None.

Why should a mercury cell NOT be shorted?

Description : Why should a mercury cell NOT be shorted?

Last Answer : The danger of explosion.

Why should a mercury cell NOT be shorted?

Description : Why should a mercury cell NOT be shorted?

Last Answer : The danger of explosion.

What is the only way to cause an SCR to stop conducting?

Description : What is the only way to cause an SCR to stop conducting?

Last Answer : The forward bias must be reduced below the minimum conduction level.

The SCR is primarily used for what function?

Description : The SCR is primarily used for what function?

Last Answer : The SCR is primarily used for switching power on or off.

What are two transistor tests that can be done with an ohmmeter?

Description : What are two transistor tests that can be done with an ohmmeter?

Last Answer : Gain and junction resistance.

When checking a diode with an ohmmeter, what is indicated by two high resistance measurements?

Description : When checking a diode with an ohmmeter, what is indicated by two high resistance measurements?

Last Answer : The diode is open or has a high-forward resistance.

To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Description : To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Last Answer : Answer: B

When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when _____________. A. there is no meter deflection B. the meter deflects to a low resistance value and remains there C. the meter deflects to a low resistance value and slowly increases towards infinity D. the meter deflects to a low resistance value and increases rapidly to a higher value, but stays fairly low

Description : When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when _____________. A. there is no meter deflection B. the meter deflects to a low resistance value and ... deflects to a low resistance value and increases rapidly to a higher value, but stays fairly low

Last Answer : Answer: C

When you are using an ohmmeter to test a transistor, what range settings should be avoided?

Description : When you are using an ohmmeter to test a transistor, what range settings should be avoided?

Last Answer : Any range setting that produces a current flow through the transistor that exceeds 1 milliamp (usually R x 1 range)

Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Description : Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Last Answer : De-energized

How could you check a 1/500-ampere fuse with an ohmmeter?

Description : How could you check a 1/500-ampere fuse with an ohmmeter?

Last Answer : Use a resistor in series with the fuse when you check it with the ohmmeter.

You have just checked a 1/500-ampere fuse with an ohmmeter and find it is open. Checking the replacement fuse shows the replacement fuse is open also. Why would the replacement fuse indicate open?

Description : You have just checked a 1/500-ampere fuse with an ohmmeter and find it is open. Checking the replacement fuse shows the replacement fuse is open also. Why would the replacement fuse indicate open?

Last Answer : The ohmmeter causes more than 1/500 ampere through the fuse when you check the fuse, thus it opens the fuse.

What area of an ohmmeter scale should be used when measuring circuits?

Description : What area of an ohmmeter scale should be used when measuring circuits?

Last Answer : The middle of the scale.

What is used to provide the ohmmeter with several ranges?

Description : What is used to provide the ohmmeter with several ranges?

Last Answer : An ohmmeter has several internal range resistors and a switch or a series of jacks to select the proper range.

How is a series-type ohmmeter connected to the circuit being measured?

Description : How is a series-type ohmmeter connected to the circuit being measured?

Last Answer : The ohmmeter is connected in series with the resistance to be measured.

What other measurement can an ohmmeter make?

Description : What other measurement can an ohmmeter make?

Last Answer : Circuit continuity.

What electrical quantity is measured by an ohmmeter?

Description : What electrical quantity is measured by an ohmmeter?

Last Answer : Resistance.

The R x 100 resistance selection on an ohmmeter has what amount of resistance compared to the R x 10 selection?

Description : The R x 100 resistance selection on an ohmmeter has what amount of resistance compared to the R x 10 selection?

Last Answer : 1/10.

. A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : . A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

The R x 100 resistance selection on an ohmmeter has what amount of resistance compared to the R x 10 selection?

Description : The R x 100 resistance selection on an ohmmeter has what amount of resistance compared to the R x 10 selection?

Last Answer : 1/10.

A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Description : A full-scale deflection on an ohmmeter scale indicates what resistance between the leads?

Last Answer : Zero.

Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Description : Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Last Answer : Answer: D

Los Angeles testing machine is used to conduct (A) Abrasion test (B) Impact test (C) Attrition test (D) Crushing strength test

Description : Los Angeles testing machine is used to conduct (A) Abrasion test (B) Impact test (C) Attrition test (D) Crushing strength test

Last Answer : Answer: Option A

A test harness is a A. A high level document describing the principles, approach and major objectives of the organization regarding testing B. A distance set of test activities collected into a manageable phase of a project C. A test environment comprised of stubs and drives needed to conduct a test D. A set of several test cases for a component or system under test

Description : A test harness is a A. A high level document describing the principles, approach and major objectives of the organization regarding testing B. A distance set of test activities collected into a manageable phase ... conduct a test D. A set of several test cases for a component or system under test

Last Answer : C. A test environment comprised of stubs and drives needed to conduct a test

Does a rectifier tube conduct on the positive or negative alternation of the input signal?

Description : Does a rectifier tube conduct on the positive or negative alternation of the input signal?

Last Answer : Positive.

What term describes a device used to conduct heat away from a component?

Description : What term describes a device used to conduct heat away from a component?

Last Answer : A thermal shunt.

An ac voltage is applied across a diode. The tube will conduct when

Description : An ac voltage is applied across a diode. The tube will conduct when

Last Answer : Positive.

Before a diode will conduct, the cathode must be what polarity relative

Description : Before a diode will conduct, the cathode must be what polarity relative

Last Answer : Negative.

Which of the following is not a characteristic of organic compounds? (a) They usually have low melting points. (b) They usually are only slightly soluble or insoluble in water. (c) If water soluble they seldom conduct an electric current. (d) Bonds which bind the atoms together are nearly always ionic.

Description : Which of the following is not a characteristic of organic compounds? (a) They usually have low melting points. (b) They usually are only slightly soluble or insoluble in water. (c) If water ... they seldom conduct an electric current. (d) Bonds which bind the atoms together are nearly always ionic.

Last Answer : Bonds which bind the atoms together are nearly always ionic.

Superconductors are those elements – (1) Whose conductivity is intermediate between metals and insulators (2) Whose resistance falls almost to zero at very low temperature (3) Which conduct electricity only at super-high temperature (4) Which conduct electricity only, at super-high temperatures

Description : Superconductors are those elements – (1) Whose conductivity is intermediate between metals and insulators (2) Whose resistance falls almost to zero at very low temperature (3) Which conduct electricity only at super-high temperature (4) Which conduct electricity only, at super-high temperatures

Last Answer : (2) Whose resistance falls almost to zero at very low temperature Explanation: Superconductivity is a phenomenon of exactly zero electrical resistance and expulsion of magnetic fields occurring in ... lines from the interior of the superconductor as it transitions into the superconducting state.

Elements that do not conduct electricity and heat which tends to accept electrons?

Description : Elements that do not conduct electricity and heat which tends to accept electrons?

Last Answer : Non-Metals

Elements that conduct electricity and heat which tends to lose electrons are called?

Description : Elements that conduct electricity and heat which tends to lose electrons are called?

Last Answer : Metals

Superconductors are those elements (1) Whose conductivity is intermediate between metals and insulators (2) Whose resistance falls almost to zero at very low temperatures (3) which turn into insulators at very low temperatures (4) which conduct electricity only at super-high temperatures

Description : Superconductors are those elements (1) Whose conductivity is intermediate between metals and insulators (2) Whose resistance falls almost to zero at very low temperatures (3) which turn into insulators at very low temperatures (4) which conduct electricity only at super-high temperatures

Last Answer : Whose resistance falls almost to zero at very low temperatures

Have you ever experienced a situation where a store or restaurant gave you the wrong change (shorted you) and what did you do about it?

Description : Have you ever experienced a situation where a store or restaurant gave you the wrong change (shorted you) and what did you do about it?

Last Answer : answer:If they “decided to stick” with the original, despite my insistence that I gave them $40, I’d demand the manager and have them count the drawer. I have absolutely no patience for shysters, and $10 is not “no big deal” to me.

Has anyone else had their dashboard lights shorted out by motor oil?

Description : Has anyone else had their dashboard lights shorted out by motor oil?

Last Answer : No, but…I had a new battery installed a couple years ago that flipped my gas gage needle backwards and while it has been spun around again, several times with a magnet, it still flips back into the dead zone every so often. haha Car stuff…PITA!

Why is the side-side shorted during the short circuit test in the transformer ?

Description : Why is the side-side shorted during the short circuit test in the transformer ?

Last Answer : During this test, any side of the transformer can be shorted, but for the following reasons, the side-side is shorted and 1. Lay-range instruments have the advantage of being connected to the high side ... both windings below 3% of the rated output , so it is convenient to measure on the high side.

How do you repair driver side airbag circuit low resistance or shorted Ford F150?

Description : How do you repair driver side airbag circuit low resistance or shorted Ford F150?

Last Answer : It might be a problem with the "clock spring".