What component causes a generator to produce dc voltage rather than ac voltage at its output terminals?

What component causes a generator to produce dc voltage  rather than ac voltage at its output terminals?
by

1 Answer

Answer :

A commutator
by

Related questions

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

Why does using ac vice dc bias voltage result in a stronger output signal?

Description : Why does using ac vice dc bias voltage result in a stronger output signal?

Last Answer : Because an ac bias voltage of the proper frequency and level places the input signal away from both steps in the magnetism curve. The result is two undistorted output signals that are combined into one strong output.

An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. positive deflection of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Description : An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. ... of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Last Answer : Answer: C

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals

Description : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance to remain constant immediately after the fault, acceleration of the generator rotor is

Last Answer : A large AC generator, supplying power to an infinite bus, has a sudden short-circuit occurring at its terminals. Assuming the prime mover input and the voltage behind the transient reactance ... , acceleration of the generator rotor is inversely proportional to the moment of inertia of the machine

The voltage developed by an AC generator is controlled by varying the ____________. A. speed of the prime mover B. AC excitation to the field C. DC excitation to the field D. DC excitation of the voltage regulator

Description : The voltage developed by an AC generator is controlled by varying the ____________. A. speed of the prime mover B. AC excitation to the field C. DC excitation to the field D. DC excitation of the voltage regulator

Last Answer : Answer: C

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Description : What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Last Answer : a. Reproduces a stronger output signal. b. Greatly improves the SNR. c. Greatly reduces the natural tape hiss.

Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.

A generator uses what method to produce a voltage?

Description : A generator uses what method to produce a voltage?

Last Answer : Magnetic.

What two factors can cause output dc voltage to change?

Description : What two factors can cause output dc voltage to change?

Last Answer : Ac line voltage and a change in load resistance.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Last Answer : 200 millivolts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

The most practical way to control the voltage output of an AC generator is to vary the _____________. A. number of windings B. speed of the rotating field C. strength of the rotating magnetic field D. power factor of the load

Description : The most practical way to control the voltage output of an AC generator is to vary the _____________. A. number of windings B. speed of the rotating field C. strength of the rotating magnetic field D. power factor of the load

Last Answer : Answer: C

The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Description : The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the ____________. A. prime mover speed droop B. number of poles C. alternator field excitation D. load on the alternator

Last Answer : Answer: C

The output voltage of a 440 volt, 60 Hz AC generator is controlled by the ______________. A. load on the alternator B. load on the prime mover C. speed of the prime mover D. exciter output voltage

Description : The output voltage of a 440 volt, 60 Hz AC generator is controlled by the ______________. A. load on the alternator B. load on the prime mover C. speed of the prime mover D. exciter output voltage

Last Answer : Answer: D

A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Description : A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Last Answer : Answer: C

The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the _____________. A. prime mover speed B. exciter output voltage C. load on the alternator D. number of poles

Description : The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the _____________. A. prime mover speed B. exciter output voltage C. load on the alternator D. number of poles

Last Answer : Answer: B

The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Description : The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Last Answer : Answer: D

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Description : When using multiple SAW arc systems (twin wires etc), the arcs often have different polarities or use all AC rather than DC polarity, this is to? a) Prevent arc blow between arcs b) To maximize productivity c) To even out the power factor on the mains supply d) Make it easier to initiate the arc

Last Answer : a) Prevent arc blow between arcs

Most large alternators have a small dc generator built into them. What is its purpose?

Description : Most large alternators have a small dc generator built into them. What is its purpose?

Last Answer : To provide dc current for the rotating field.

Why is the dc scale on a multimeter different than the ac scale?

Description : Why is the dc scale on a multimeter different than the ac scale?

Last Answer : The meter movement reacts to average ac voltage and current and the effective value is desired.

In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Last Answer : b) Equal to DC value

What are the differences between the components of a dc generator and a dc motor?

Description : What are the differences between the components of a dc generator and a dc motor?

Last Answer : There are no differences.

What is the purpose of a dc generator that has been modified to function as an amplidyne?

Description : What is the purpose of a dc generator that has been modified to function as an amplidyne?

Last Answer : It can serve as a power amplifier.

What is the effect of motor reaction in a dc generator?

Description : What is the effect of motor reaction in a dc generator?

Last Answer : A force which causes opposition to applied turning force.

How can field strength be varied in a practical dc generator?

Description : How can field strength be varied in a practical dc generator?

Last Answer : By varying the input voltage to the field coils

Which component is mainly used in a DC generator: a.slip ring b. commutator c. magnet d. coil

Description : Which component is mainly used in a DC generator: a.slip ring b. commutator c. magnet d. coil

Last Answer : b. commutator

What determines the phase relationship between the voltages in a two-phase ac generator?

Description : What determines the phase relationship between the voltages in a two-phase ac generator?

Last Answer : Placement of armature coils.

4. The essential difference between an AC generator and a DC generator is that -Physics-10

Description : 4. The essential difference between an AC generator and a DC generator is that -Physics-10

Last Answer : AC generator has slip rings while the DC generator has a commutator. AC generators have two rings known as the slip rings while DC generators have two half rings known as the commutator. This is main difference between AC generator and DC generator.

A DC generator is used to supply direct current in order to maintain an AC generator field and is known as a/an _____________. A. rotor B. stator C. exciter D. armature

Description : A DC generator is used to supply direct current in order to maintain an AC generator field and is known as a/an _____________. A. rotor B. stator C. exciter D. armature

Last Answer : Answer: C

The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Description : The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Last Answer : Answer: B

Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Description : Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Last Answer : d. AC generato

Which of the following are the parts of a DC generator that convert the AC in the armature to DC in the external circuit. Are these parts the: w) field poles x) slip rings and the brushes y) commutator and the brushes z) armature and the core

Description : Which of the following are the parts of a DC generator that convert the AC in the armature to DC in the external circuit. Are these parts the: w) field poles x) slip rings and the brushes y) commutator and the brushes z) armature and the core

Last Answer : ANSWER: Y -- COMMUTATOR AND THE BRUSHES

What is the difference between an AC and DC generator?

Description : What is the difference between an AC and DC generator?

Last Answer : The generator which generates DC voltage is called DC generator and generator which generates AC voltage is called AC generator (or) Alternator. In DC generator armature is rotated and field winding ... generator. A DC generator can generate low voltages but an AC generator can generate upto 11kv.

What is the basic difference between the primaries of ac and dc rate generators?

Description : What is the basic difference between the primaries of ac and dc rate generators?

Last Answer : The method of primary excitation (ac and permanent magnet).

List three meter movements that can measure either ac or dc without the use of a rectifier.

Description : List three meter movements that can measure either ac or dc without the use of a rectifier.

Last Answer : Electrodynamic, moving vane, and hot-wire or thermocouple.

What type of meter movement reacts to voltage rather than current?

Description : What type of meter movement reacts to voltage rather than current?

Last Answer : Electrostatic.

What is added to a sawtooth generator to produce a trapezoidal wave?

Description : What is added to a sawtooth generator to produce a trapezoidal wave?

Last Answer : A resistor.

Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Description : Which component of the receiver produces the signal that is mixed with the received signal to produce the IF signal?

Last Answer : Local oscillator.

What component is in parallel with the output in a parallel limiter?

Description : What component is in parallel with the output in a parallel limiter?

Last Answer : The diode.

If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

How does dc bias added to the input signal correct the distortion in the output signal?

Description : How does dc bias added to the input signal correct the distortion in the output signal?

Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.