Why does using ac vice dc bias voltage result in a stronger output signal?

Why does using ac vice dc bias voltage result in a stronger  output signal?
by

1 Answer

Answer :

Because an ac bias voltage of the proper frequency and level  places the input signal away from both steps in the magnetism curve.  The result is two undistorted output signals that are combined into  one strong output.
by

Related questions

Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Description : Why does adding dc vice ac bias voltage to the input signal result in a poor signal-to-noise ratio (SNR)?

Last Answer : With dc bias, the SNR is poor because only a small portion of the magnetism curve is straight enough to use, thus the output signal is weak compared with the natural tape hiss.

What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Description : What are three advantages of adding an ac bias voltage to the input signal instead of adding a fixed dc bias voltage?

Last Answer : a. Reproduces a stronger output signal. b. Greatly improves the SNR. c. Greatly reduces the natural tape hiss.

How does dc bias added to the input signal correct the distortion in the output signal?

Description : How does dc bias added to the input signal correct the distortion in the output signal?

Last Answer : The dc bias moves the input signal away from the step in the magnetism curve. This prevents the input signal from crossing the zero-point of the magnetism curve.

What component causes a generator to produce dc voltage rather than ac voltage at its output terminals?

Description : What component causes a generator to produce dc voltage rather than ac voltage at its output terminals?

Last Answer : A commutator

What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Description : What would be the output of a negative clamper with a bias potential of −5 volts and an input voltage swing from +50 to −50 volts?

Last Answer : -5 volts.

What causes dc bias energy to be absorbed by avalanche electrons and given up to the microwave field applied to an avalanche transit-time diode?

Description : What causes dc bias energy to be absorbed by avalanche electrons and given up to the microwave field applied to an avalanche transit-time diode?

Last Answer : The negative-resistance property.

The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the device C. allowing the use of either AC or DC in the load circuit D. changing the direction of current through the load

Description : The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the ... use of either AC or DC in the load circuit D. changing the direction of current through the load

Last Answer : Answer: B

If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Description : If the mu of a tube is 85 and the signal at the control grid is 4 volts ac, the plate voltage will vary by what amount?

Last Answer : 340 volts.

The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Description : The plate voltage of a tube will vary 126 volts when a 3-volt ac signal is applied to the control grid. What is the gain of this tube?

Last Answer : 42.

If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the input signal C) Need for high dc collector supply D) Clipping of output in the negative half of the input signal

Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal

Last Answer : B) Clipping of output in the positive half of the input signal

What two factors can cause output dc voltage to change?

Description : What two factors can cause output dc voltage to change?

Last Answer : Ac line voltage and a change in load resistance.

An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB

Last Answer : D) AB

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Description : The output voltage of a three-phase alternator is regulated by the _____________. A. AC voltage to the armature B. AC voltage to the field C. DC voltage to the armature D. DC voltage to the field

Last Answer : Answer: D

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Description : A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?

Last Answer : Negative potential.

What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Description : What type damper (with bias) clamps the most negative extremity of the output waveform to a negative potential?

Last Answer : Positive clamper with negative bias.

In signal generators, what device is used to regulate the voltage of the output signal?

Description : In signal generators, what device is used to regulate the voltage of the output signal?

Last Answer : Attenuator.

The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the bridge B. reversing the current flow through the control winding C. connecting the load to the input side of the bridge D. reversing the current flow through the bias winding

Description : The device in figure 'B' shown in the illustration can be used to control an AC load yet maintain its high gain by ______________. EL-0091 A. connecting the load to the output side of the ... connecting the load to the input side of the bridge D. reversing the current flow through the bias winding

Last Answer : Answer: C

To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Description : To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Last Answer : Positive, more positive.

A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).

Description : A, when there is an increase in the input voltage, the forward bias of Q1 increases/decreases (which one).

Last Answer : Increases.

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

What is the basic difference between the primaries of ac and dc rate generators?

Description : What is the basic difference between the primaries of ac and dc rate generators?

Last Answer : The method of primary excitation (ac and permanent magnet).

Why is the dc scale on a multimeter different than the ac scale?

Description : Why is the dc scale on a multimeter different than the ac scale?

Last Answer : The meter movement reacts to average ac voltage and current and the effective value is desired.

List three meter movements that can measure either ac or dc without the use of a rectifier.

Description : List three meter movements that can measure either ac or dc without the use of a rectifier.

Last Answer : Electrodynamic, moving vane, and hot-wire or thermocouple.

Which of the following statement is correct ? (A) Modem is a software (B) Modem helps in stabilizing the voltage (C) Modem is the operating system (D) Modem converts the analog signal into digital signal and vice-versa

Description : Which of the following statement is correct ? (A) Modem is a software (B) Modem helps in stabilizing the voltage (C) Modem is the operating system (D) Modem converts the analog signal into digital signal and vice-versa

Last Answer : (D) Modem converts the analog signal into digital signal and vice-versa

rid-leak biasing in effect rectifies the input ac signal. What feature

Description : rid-leak biasing in effect rectifies the input ac signal. What feature

Last Answer : Unequal charge and discharge paths of the coupling capacitor Cc.

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

A transformer works with (1) alternating current only (2) direct current only (3) both AC and DC (4) any signal

Description : A transformer works with (1) alternating current only (2) direct current only (3) both AC and DC (4) any signal

Last Answer : alternating current only

Differentiate AC and DC signal conditioning.

Description : Differentiate AC and DC signal conditioning. 

Last Answer : AC signal conditioning DC signal conditioning  Excitation source is only AC for AC signal conditioning. Excitation source can be ac or dc for DC signal conditioning. AC signal conditioning ... low frequency.  Demodulation is present in AC. Demodulation is absent in DC.

In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Description : In the output of an ac error detector, what indicates the (a) direction and (b) amount of control necessary for correspondence?

Last Answer : (a) Phase. (b) Amplitude.

When three-phase AC power is supplied to the device shown in the illustration, the output will be _____________. EL-0063 A. single-phase AC B. split-phase AC C. three-phase DC D. unidirectional DC

Description : When three-phase AC power is supplied to the device shown in the illustration, the output will be _____________. EL-0063 A. single-phase AC B. split-phase AC C. three-phase DC D. unidirectional DC

Last Answer : Answer: D

In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output.

Description : In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a ……… …………through the switching devices over short interval of time. A) constant current B) constant voltage C) constant power D) none of the (A), (B), (C)

Last Answer : In practice, a current source inverter consists of an AC/ DC converter with a large inductance ‘L’ in the output. This inductance maintains a constant current through the switching devices over short interval of time. 

A positive damper clamps which extremity of the output signal to 0 volts?

Description : A positive damper clamps which extremity of the output signal to 0 volts?

Last Answer : Most negative.

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Description : select the correct response from the choices given in the parentheses. Q-20. In a closed-loop configuration the output signal is determined by (the input signal, the feedback signal, both).

Last Answer : Both the input signal and the feedback signal.

If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?

Last Answer : 200 millivolts.

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?

Last Answer : . A different shape than the input signals but larger in amplitude.

If only one input signal is used with a difference amplifier, what will the output signal be?

Description : If only one input signal is used with a difference amplifier, what will the output signal be?

Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.

If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?

Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than

. If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?

Last Answer : No output (the signals will "cancel out").

In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal? In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

what causes the initial and final pulses on the receiver output signal?

Description : what causes the initial and final pulses on the receiver output signal?

Last Answer : Leakage from the duplexer.

How is the output signal developed in the common-emitter detector?

Description : How is the output signal developed in the common-emitter detector?

Last Answer : By the collector current flow through R4.