Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?

Why are drum-type armatures preferred over the Gramme ring armature in modern dc generators?
by

1 Answer

Answer :

Drum-type armatures are more efficient, because flux lines are  cut by both sides of each coil.
by

Related questions

How is the disadvantage of the Gramme-ring armature overcome in the drum-wound armature?

Description : How is the disadvantage of the Gramme-ring armature overcome in the drum-wound armature?

Last Answer : By winding the armature in a way that places the entire coil where it is exposed to maximum flux.

Why is the Gramme-ring armature not more widely used

Description : Why is the Gramme-ring armature not more widely used

Last Answer : Only outside of coils cut flux (inefficient).

Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method...

Description : Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method due to:  (1) Better speed regulation (2) Less loss in external resistance (3) Simplicity in control circuit (4) Reduced cost of controller

Last Answer : Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method due to: Better speed regulation.

In DC generators, armature reaction is produced actually by (A) Its field current. (B) Armature conductors. (C) Field pole winding. (D) Load current in armature.

Description : In DC generators, armature reaction is produced actually by (A) Its field current. (B) Armature conductors. (C) Field pole winding. (D) Load current in armature.

Last Answer : Ans: D Because load current in armature gives rise to armature mmf which react with main field mmf.

In DC generators, armature reaction is produced by the:

Description : In DC generators, armature reaction is produced by the: (A) field current (B) armature conductors (C) field pole winding (D) load current in armature

Last Answer : In DC generators, armature reaction is produced by the: load current in armature

Armature reaction in a dc motor causes a shift of the neutral plane in which direction?

Description : Armature reaction in a dc motor causes a shift of the neutral plane in which direction?

Last Answer : Opposite the rotation.

What is the basic difference between the primaries of ac and dc rate generators?

Description : What is the basic difference between the primaries of ac and dc rate generators?

Last Answer : The method of primary excitation (ac and permanent magnet).

What are the three classifications of dc generators?

Description : What are the three classifications of dc generators?

Last Answer : Series-wound, shunt-wound, and compound-wound

Modern DC generators are fitted with commutating poles to _____________. A. prevent motorizing B. reduce sparking C. reduce the load on the main poles D. reduce spring pressure on the brushes

Description : Modern DC generators are fitted with commutating poles to _____________. A. prevent motorizing B. reduce sparking C. reduce the load on the main poles D. reduce spring pressure on the brushes

Last Answer : Answer: B

An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. cause the slip rings to melt C. cause a low voltage differential to develop between the armature and the bus D. cause high currents to be induced in the field windings

Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings

Last Answer : Answer: D

Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical appliances made of silicon steel contains maximum percentage of silicon (about 4%)? (A) Armature of small motors/generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Description : Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical ... /generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Last Answer : (D) High frequency transformers

In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Description : In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Last Answer : Ans: a

In D.C. generators, current to the external circuit from armature is given through?

Last Answer : In D.C. generators, current to the external circuit from armature is given through commutator commutator.

Which type of winding is preferred for armature windings of alternator? Why?

Description : Which type of winding is preferred for armature windings of alternator? Why?

Last Answer : Double layer, short pitched and distributed type of armature winding. It eliminates high frequency harmonics hence it makes induced emf more sinusoidal.

What is preferred location for pressure instrument nozzle on drum?

Description : What is preferred location for pressure instrument nozzle on drum?

Last Answer : Answer: Must be anywhere in the vapor space, preferable at the top section of drum

What is preferred location for steam out nozzle on drum?

Description : What is preferred location for steam out nozzle on drum?

Last Answer : Answer: At the end opposite to the maintenance access.

What is preferred location for process nozzles on drum?

Description : What is preferred location for process nozzles on drum?

Last Answer : Answer: Minimum from the tangent line.

Motors, switches, voltage regulators, generators, etc., are a few examples of emi sources. What type of emi comes from these sources?

Description : Motors, switches, voltage regulators, generators, etc., are a few examples of emi sources. What type of emi comes from these sources?

Last Answer : Man-made.

Lap windings are used in generators designed for what type of application?

Description : Lap windings are used in generators designed for what type of application?

Last Answer : Higher load currents are possible

Tracks on each channel of a magnetic drum are grouped into what?

Description : Tracks on each channel of a magnetic drum are grouped into what?

Last Answer : Sectors.

How does a magnetic drum differ from a magnetic disk?

Description : How does a magnetic drum differ from a magnetic disk?

Last Answer : The tracks in which the data is stored are assigned to channels that form circular bands around the drum.

Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Description : Why are LEDs preferred over laser diodes for low- and moderate-frequency analog applications?

Last Answer : LEDs require less complex circuitry than lasers.

Why is a multimeter preferred over separate meters?

Description : Why is a multimeter preferred over separate meters?

Last Answer : It is much more convenient to have one meter with several functions than several meters each with a single function.

Which one is not present in AC generator: a. Armature b. magnet c. slip ring d. commutator

Description : Which one is not present in AC generator: a. Armature b. magnet c. slip ring d. commutator

Last Answer : c. slip ring

Why AC systems are preferred over DC systems?

Description : Why AC systems are preferred over DC systems?

Last Answer : Due to following reasons, AC systems are preferred over DC systems: a. It is easy to maintain and change the voltage of AC electricity for transmission and distribution. b. Plant cost for AC ... the sine wave current will naturally tend to zero at some point making the current easier to interrupt.

What is armature reaction?

Description : What is armature reaction?

Last Answer : Distortion of the main field due to the effects of armature current.

In single-phase alternators, in order for the voltages induced in all the armature windings to add together for a single output, how must the windings be connected?

Description : In single-phase alternators, in order for the voltages induced in all the armature windings to add together for a single output, how must the windings be connected?

Last Answer : In series.

What are report program generators used for?

Description : What are report program generators used for?

Last Answer : To generate programs to print detail and summary reports of data files.

Range-marker generators produce pulses based on what radar constant?

Description : Range-marker generators produce pulses based on what radar constant?

Last Answer : The radar mile (12.36 microseconds).

What are the two classifications of wave generators according to their output waveshapes?

Description : What are the two classifications of wave generators according to their output waveshapes?

Last Answer : Sinusoidal and nonsinusoidal.

What term applies to the use of two or more generators to supply a common load?

Description : What term applies to the use of two or more generators to supply a common load?

Last Answer : Parallel operation.

What is the main disadvantage of series generators?

Description : What is the main disadvantage of series generators?

Last Answer : Output voltage varies as the load varies

Generators convert mechanical motion to electrical energy using what principle?

Description : Generators convert mechanical motion to electrical energy using what principle?

Last Answer : Magnetic induction

In signal generators, what device is used to regulate the voltage of the output signal?

Description : In signal generators, what device is used to regulate the voltage of the output signal?

Last Answer : Attenuator.

Ships’ generators produce 450-volt, three-phase, ac power; however, most equipment uses 117-volt, single-phase power What transformers and connections are used to convert 450- volt, threephase power to 117-volt, single-phase power?

Description : Ships’ generators produce 450-volt, three-phase, ac power; however, most equipment uses 117-volt, single-phase power What transformers and connections are used to convert 450- volt, threephase power to 117-volt, single-phase power?

Last Answer : A method of generating oscillations, a method of turning the oscillations on and off (keying), and an antenna to radiate the energy.

In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Description : In modern car synchromesh gearbox is preferred over constant mesh gearbox. Justify its application with suitable illustration

Last Answer : Reason of synchromesh gear box preferred over constant mesh gearbox  1) No need of double declutching as in case of constant mesh gearbox.  2) Smooth engagement of higher gears due to synchromesh ... lay shaft gears to main shaft gear and then to the main shaft through synchronizer device 

Moving the rheostat handle shown in the illustration, that is used to control a DC generator, towards the 'raise' direction will increase the _____________. EL-0030 A. field resistance B. armature resistance C. armature speed D. line voltage

Description : Moving the rheostat handle shown in the illustration, that is used to control a DC generator, towards the 'raise' direction will increase the _____________. EL-0030 A. field resistance B. armature resistance C. armature speed D. line voltage

Last Answer : Answer: D

The torque produced by a DC motor armature is the product of the force acting at the armature surface multiplied by _____________. A. work done by the armature in one revolution B. effective armature diameter at which the force acts C. maximum moment arm at the center of rotation of the armature D. perpendicular distance to its center of rotation

Description : The torque produced by a DC motor armature is the product of the force acting at the armature surface multiplied by _____________. A. work done by the armature in one revolution B. effective ... arm at the center of rotation of the armature D. perpendicular distance to its center of rotation

Last Answer : Answer: D

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

If the connections for the field and the armature on a DC motor are reversed, _____________. A. the motor will run as a generator B. the motor will not run C. the direction of rotation will be the same D. the direction of rotation will be reversed

Description : If the connections for the field and the armature on a DC motor are reversed, _____________. A. the motor will run as a generator B. the motor will not run C. the direction of rotation will be the same D. the direction of rotation will be reversed

Last Answer : Answer: C

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an ______________. A. shorted shunt field coil B. open armature coil C. reversed commutating pole D. overload

Description : If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an ______________. A. shorted shunt field coil B. open armature coil C. reversed commutating pole D. overload

Last Answer : Answer: A

A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Description : A shorted armature coil in a DC motor can be detected by _____________. A. sparking at the brushes B. shiny armature coil C. worn grooves in the armature D. undercut mica

Last Answer : Answer: A

An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a bar to bar test of the armature B. visually inspect the armature windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Description : An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a ... windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Last Answer : Answer: A

An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Description : An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Last Answer : Answer: B

DC generator voltage is decreased by cutting _____________. A. in field resistance B. out field resistance C. in armature resistance D. out armature resistance

Description : DC generator voltage is decreased by cutting _____________. A. in field resistance B. out field resistance C. in armature resistance D. out armature resistance

Last Answer : Answer: A

A short circuit in the armature of a DC motor will cause the motor to _____________. A. run fast B. hum when energized C. spark at the brushes D. fail to start

Description : A short circuit in the armature of a DC motor will cause the motor to _____________. A. run fast B. hum when energized C. spark at the brushes D. fail to start

Last Answer : Answer: C

Which of the listed conditions will occur if the polarity of the field poles and the direction of current to the brushes of a DC motor were both reversed? A. The motor would not start. B. The direction of rotation of the armature would be reversed. C. The direction of rotation of the armature would be unchanged. D. The field pole windings would become overheated.

Description : Which of the listed conditions will occur if the polarity of the field poles and the direction of current to the brushes of a DC motor were both reversed? A. The motor would not start. ... direction of rotation of the armature would be unchanged. D. The field pole windings would become overheated.

Last Answer : Answer: C