Description : What are the two basic types of tape buffering reeling systems?
Last Answer : a. Spring-tension buffering systems. b. Vacuum-column buffering systems.
Description : How do the tape guides on a tape reeling system protect the tape from damage during operation?
Last Answer : They keep the tape straight with respect to both the supply and take-up reels and the magnetic heads.
Description : What type of reeling system best controls a tape recorder's tape tension during starts and stops?
Last Answer : A tape buffering reeling system
Description : What are two advantages of a two-motor reeling system over a take-up control reeling system?
Last Answer : The two-motor configuration runs in both directions and a holdback voltage helps control tape tension, but it does not properly control tape tension during starts and stops.
Description : What are two disadvantages of the take-up control reeling system?
Last Answer : a. It only works in one direction. b. The tape tension varies as the supply reel unwinds, which can cause damage during starts and stops.
Description : What are four types of tape errors that can degrade a magnetic recording system’s performance?
Last Answer : Signal dropout, noise, skew, and level. Dropout is the most common.
Description : What type of modulator is most commonly used in modern radar systems?
Last Answer : Line-pulsed.
Last Answer : The process by which the filament is lifted from the cocoon is called reeling.
Description : Technical manuals for tape recorders can state the SNR in what three different ways?
Last Answer : a. Root-mean-square (RMS) signal-to-RMS noise. b. Peak-to-peak signal-to-RMS noise. c. Peak signal-to-RMS noise.
Description : Magnetic tape recorders can have up to three different heads installed. What are the three functions performed by a recorder's heads?
Last Answer : Record, reproduce, and erase.
Description : A tape pack is buckled and deformed as shown in figure 2- 4. What are three possible causes for this condition?
Last Answer : a. Reel has a distorted hub, b. tape wound over small particle deposited on hub, and c. tape wound on reel with tension increasing toward end of winding.
Description : If magnetic tape is stored in areas with temperature and humidity extremes, what are three types of tape damage that may occur?
Last Answer : Oxide shedding, layer-to-layer sticking, and tape deformation.
Description : Magnetic tape is made of what three basic materials?
Last Answer : a. Base material. b. Coating of magnetic oxide particles. c. Glue that bonds the particles to the base.
Description : Digital magnetic tape recorders used to store and retrieve digital data fall into what three categories?
Last Answer : a. Computer-compatible digital tape recorders. b. Telemetry digital tape recorders. c. Instrumentation digital tape recorders
Description : What three formats are used for digital magnetic tape recording?
Last Answer : 1) Serial, (2) parallel, and (3) serial-parallel.
Description : In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?
Last Answer : a. Data used by digital computers. b. Pulsed squarewave signals. c. Digitized analog waveforms.
Description : What are the three units of measure most commonly used when referring to af power measurements?
Last Answer : DB, dBm, and vu.
Last Answer : Magnetic recording tape is most commonly made from ferric oxide.
Description : ______ is most commonly used for making magnetic recording tape.
Last Answer : Ferric oxide is most commonly used for making magnetic recording tape.
Description : What amount of flat tape or round cord is required to single lace a group of conductors?
Last Answer : Two and one-half times the length of the longest conductor in the group.
Description : Why is flat tape preferred instead of round cord when wire bundles are laced?
Last Answer : Round cord has a tendency to cut into the wire insulation.
Description : Why is friction tape used in splicing?
Last Answer : As a protective covering over the rubber tape.
Description : What equipment should you use to de-magnetize a magnetic tape transport?
Last Answer : A hand-held degausser.
Description : When cleaning the parts of a tape transport, why should you switch lint-free cloths and swabs often?
Last Answer : You may transfer dirt or oxide particles from one part of the tape transport to another
Description : Sometimes it's necessary, but why should you avoid using cotton swabs when cleaning a magnetic tape transport?
Last Answer : Cotton swabs are not lint free.
Description : How do dual-motor dual capstan drives maintain a constant tape tension while operating in either a forward or reverse direction?
Last Answer : Each capstan is driven by its own motor. It maintains tape tension by slowing down one of the motors. When the tape motion is reversed, the opposite motor is slowed down.
Description : . How do tape transports with differential velocity capstans maintain a constant tape tension in the area around the magnetic heads?
Last Answer : The supply capstan is slightly larger than the take-up capstan. This causes the take-up capstan to pull the tape slightly faster than the supply capstan feeds the tape.
Description : How do closed-loop capstan drive tape transports overcome the disadvantages of the open-loop drive design?
Last Answer : Closed loop capstan drive transports use more than one capstan to clamp the tape in the area around the magnetic head.
Description : There are two types of tape transport configurations, open loop capstan drive and closed-loop capstan drive. What are two major disadvantages of open-loop capstan drive tape transports?
Last Answer : a. Only operates in one direction. b. The tape tension and head-to-tape contact can vary.
Description : What are the four basic parts of a magnetic tape recorder's tape transport system?
Last Answer : a. Tape reeling system. b. Tape speed control system. c. Electronic subsystem. d. Basic enclosure.
Description : How do worn or sticking tape transport guides cause dynamic skew on a multi-track recorder?
Last Answer : The tape drifts past the multi-track head at an angle.
Description : The skew specification of your multi-tracked tape recorder reads " +/ - 0.20 microseconds between adjacent tracks on the same head stack at 120 ips." What does this mean?
Last Answer : One of the tracks on a magnetic head could lead or lag the track next to it by as much as 0.20 microseconds at 120 ips.
Description : Why is it important to minimize TBE jitter in magnetic tape recordings where precise timing relationships exist between two or more signals?
Last Answer : The jitter could cause noise and a loss of accuracy.
Description : What causes flutter in a tape recorder’s output?
Last Answer : Non-uniform tape motion caused by variations in tape speed.
Description : How could you check the phase response of a tape recorder?
Last Answer : Record and reproduce a square wave and see if the output on an oscilloscope is symmetrical.
Description : How should a tape recorder with good phase response reproduce a complex waveform, such as a square wave?
Last Answer : With no distortion
Description : What number harmonic is the primary harmonic distortion in magnetic tape recorders?
Last Answer : Third-order harmonic.
Description : List four factors that can degrade the frequency response of magnetic tape recorders.
Last Answer : a. A too-high or too-low bias signal level setting for the record head. b. An improper reproduce head gap. c. An improper tape transport speed. d. Poor tape-to-head contact.
Description : The frequency-response specification of your tape recorder reads within +/ - 3 dB from 150 Hz to 150 kHz at 60 ips. What does this mean?
Last Answer : The recorder can record all frequencies between 150 Hz and 150 kHz at 60 ips without varying the output amplitude more than 3 dB.
Description : You plan to measure your tape recorder’s SNR. What test equipment will you need?
Last Answer : A VTVM and a signal generator.
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : The head driver circuit of a tape recorder’s FM record electronics (figure 5-4) performs what function?
Last Answer : It amplifies the frequency-modulated output from the record oscillator and sends it to the record head.
Description : The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?
Last Answer : It generates an equalization signal which corrects any frequency response problems in the input signal from the pre-amplifier circuit.
Description : The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?
Last Answer : It takes the signal from the summing network, amplifies it, and sends it to the record head for recording.
Description : What two types of record and reproduce electronics are used by magnetic tape recorders?
Last Answer : . a. Direct record (AM). b. Frequency modulation (FM).
Description : What two preventive maintenance actions must you do regularly to increase magnetic head life and to ensure good tape recording and playback?
Last Answer : a. Keep the heads clean. b. Keep the heads demagnetized.
Description : When packaging tape reels or cartridges for shipping, what are four rules you should follow to protect the tape reels from impact and vibration?
Last Answer : a. Package reels so they’re supported by their hub, b. use reel bands, c. package reels in vertical position, d. package tape cartridges in their shipping cases.
Description : What is the correct way to hold a magnetic tape reel?
Last Answer : Always hold reel by the hub, never by the flanges. Never touch the working tape surface.
Description : What method for erasing magnetic tape is much more effective and reliable than using a recorder’s erase head?
Last Answer : Using a magnetic tape degausser