Description : After using a tape that was stored in an area where temperatures exceeded 130º F you notice pieces of oxide sticking to the recorder's tape-transport mechanism, to its magnetic heads, and onto the tape. What is the probable cause of these symptoms?
Last Answer : Oxide shedding. At temperatures above 130º F, oxide coating becomes soft and sheds.
Description : Digital magnetic tape recorders used to store and retrieve digital data fall into what three categories?
Last Answer : a. Computer-compatible digital tape recorders. b. Telemetry digital tape recorders. c. Instrumentation digital tape recorders
Description : How often should you demagnetize a recorder's magnetic heads?
Last Answer : Every 8 to 25 hours depending on the manufacturer's recommendations.
Description : What type of equipment should you use to demagnetize your recorder's magnetic heads?
Last Answer : A hand-held degausser like the manual degaussers used for degaussing magnetic tape.
Description : How should you clean your recorder's magnetic heads?
Last Answer : With a cotton-tipped applicator soaked in either isopropyl alcohol or a head cleaner recommended by the recorder's manufacturer.
Description : What are the four basic parts of a magnetic tape recorder's tape transport system?
Last Answer : a. Tape reeling system. b. Tape speed control system. c. Electronic subsystem. d. Basic enclosure.
Description : What number harmonic is the primary harmonic distortion in magnetic tape recorders?
Last Answer : Third-order harmonic.
Description : List four factors that can degrade the frequency response of magnetic tape recorders.
Last Answer : a. A too-high or too-low bias signal level setting for the record head. b. An improper reproduce head gap. c. An improper tape transport speed. d. Poor tape-to-head contact.
Description : What two types of record and reproduce electronics are used by magnetic tape recorders?
Last Answer : . a. Direct record (AM). b. Frequency modulation (FM).
Description : What method for erasing magnetic tape is much more effective and reliable than using a recorder’s erase head?
Last Answer : Using a magnetic tape degausser
Description : What are two disadvantages of using a recorder’s erase head to erase data recorded on a magnetic tape?
Last Answer : Using an erase head is slow, and it may not completely erase the tape.
Description : Technical manuals for tape recorders can state the SNR in what three different ways?
Last Answer : a. Root-mean-square (RMS) signal-to-RMS noise. b. Peak-to-peak signal-to-RMS noise. c. Peak signal-to-RMS noise.
Description : Why are record heads always placed before reproduce heads on recorders?
Last Answer : Allow you to monitor the signals you're recording.
Description : What two specifications determine the maximum frequency that a recorder's record and reproduce heads will be able to transfer?
Last Answer : a. Size of the headgap. b. Speed of the magnetic tape.
Description : . How do tape transports with differential velocity capstans maintain a constant tape tension in the area around the magnetic heads?
Last Answer : The supply capstan is slightly larger than the take-up capstan. This causes the take-up capstan to pull the tape slightly faster than the supply capstan feeds the tape.
Description : What are the three functions of the magnetic heads on a magnetic recording device?
Last Answer : a. Record the signal onto the recording medium. b. Reproduce the signal from the recording medium. c. Erase the signal from the recording medium.
Description : What type of reeling system best controls a tape recorder's tape tension during starts and stops?
Last Answer : A tape buffering reeling system
Description : What causes flutter in a tape recorder’s output?
Last Answer : Non-uniform tape motion caused by variations in tape speed.
Description : You plan to measure your tape recorder’s SNR. What test equipment will you need?
Last Answer : A VTVM and a signal generator.
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : The head driver circuit of a tape recorder’s FM record electronics (figure 5-4) performs what function?
Last Answer : It amplifies the frequency-modulated output from the record oscillator and sends it to the record head.
Description : The equalization and phase correction circuit in a tape recorder’s direct reproduce electronics (figure 5-2) performs what function?
Last Answer : It generates an equalization signal which corrects any frequency response problems in the input signal from the pre-amplifier circuit.
Description : The head driver circuit in a tape recorder’s direct record electronics component (figure 5-1) performs what function?
Last Answer : It takes the signal from the summing network, amplifies it, and sends it to the record head for recording.
Description : Which digital data encoding method helps overcome a tape recorder’s low-frequency response problems by recording two logic levels for each incoming data bit?
Last Answer : Bi-phase level encoding.
Description : What is the number of read-write heads in the drive for a 9- trac magnetic tape? A) 9 B) 16 C) 18 D) 27
Last Answer : Answer : A
Description : What is the number of read-write heads in the drive for a 9-trac magnetic tape? a. 9 b. 16 c. 18 d. 27
Last Answer : 27
Last Answer : a. 9
Description : Which single phase ac motor will you select for record players and tape recorders? a) Hysteresis motor b) Shaded pole motor c) Reluctance motor d) Two value capacitor motor
Last Answer : Which single phase ac motor will you select for record players and tape recorders? Hysteresis motor
Description : If magnetic tape is stored in areas with temperature and humidity extremes, what are three types of tape damage that may occur?
Last Answer : Oxide shedding, layer-to-layer sticking, and tape deformation.
Description : Magnetic tape is made of what three basic materials?
Last Answer : a. Base material. b. Coating of magnetic oxide particles. c. Glue that bonds the particles to the base.
Description : What three formats are used for digital magnetic tape recording?
Last Answer : 1) Serial, (2) parallel, and (3) serial-parallel.
Description : In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?
Last Answer : a. Data used by digital computers. b. Pulsed squarewave signals. c. Digitized analog waveforms.
Description : What are four sources that can cause magnetic heads to become magnetized?
Last Answer : a. During ac power losses. b. During testing. c. Because of stray magnetic fields. d. From normal use.
Description : In the actuator arm assembly of a hard disk drive transport, what device can position the magnetic heads to the correct track of a hard disk more accurately than a dc stepper motor?
Last Answer : Voice coil servo.
Description : What part of a floppy disk drive transport uses a dc stepper motor to position the magnetic heads over the recording surface of a floppy disk?
Last Answer : Actuator arm assembly.
Description : A recorder’s harmonic-distortion specification reads 2% third harmonic of a 100-kHz signal at 60 ips. What does this mean?
Last Answer : The recorder has 2% third-harmonic distortion of a 100-kHz signal at 60 ips.
Description : A recorder's erase head is always placed in what sequence on the record/reproduce track?
Last Answer : . First, before the record and reproduce heads.
Description : What equipment should you use to de-magnetize a magnetic tape transport?
Last Answer : A hand-held degausser.
Description : Sometimes it's necessary, but why should you avoid using cotton swabs when cleaning a magnetic tape transport?
Last Answer : Cotton swabs are not lint free.
Description : Why is it important to minimize TBE jitter in magnetic tape recordings where precise timing relationships exist between two or more signals?
Last Answer : The jitter could cause noise and a loss of accuracy.
Description : What two preventive maintenance actions must you do regularly to increase magnetic head life and to ensure good tape recording and playback?
Last Answer : a. Keep the heads clean. b. Keep the heads demagnetized.
Description : What is the correct way to hold a magnetic tape reel?
Last Answer : Always hold reel by the hub, never by the flanges. Never touch the working tape surface.
Description : You notice steps in the tape pack such as those in figure 2-3. What causes this and how does it damage the magnetic tape?
Last Answer : Pack slip. It's caused by loosely wound tape on a reel that is exposed to excessive vibration or heat. The vibration or heat causes the tape to shift, causing steps in the tape pack. The uneven tape will then rub against the reel's sides and the recorder's tape guides.
Description : When the relative humidity is below 10%, what happens to magnetic tape and parts of a tape recorder that could cause environmental damage?
Last Answer : Dirt build-up caused by static electricity.
Description : Your activity stores its magnetic tape in an area where the temperature is 100º F. What two types of environmental damage could occur that would make these tapes unusable?
Last Answer : Head-to-tape sticking and layer-to-layer adhesion
Description : Environmental damage to magnetic tape can occur when the tape is stored in an area that exceeds what ideal temperature and humidity ranges?
Last Answer : Ideally, use and store tape at 60 to 80º F and at 40 to 60% relative humidity.
Description : List four rules you should follow when storing magnetic tape to protect it from damage.
Last Answer : a. Make sure the tape is wound properly on the reel hub, b. store tapes vertically, c. keep storage area at right temperature and humidity, d. store away from equipment that generates stray magnetic fields.
Description : What are four types of tape errors that can degrade a magnetic recording system’s performance?
Last Answer : Signal dropout, noise, skew, and level. Dropout is the most common.
Description : What type of magnetic tape is used to record computer programs and data, and what are the additional thickness and quality standards for this type of tape?
Last Answer : digital magnetic tape is for computer programs and data. Its base material is about 50% thicker. The tape’s surface must not have blemishes or coating flaws because losing even one digital data bit could ruin the recorded computer program or data.