What is the primary difference in construction between the  basic magnetron and the negativeresistance magnetron?

1 Answer

Answer :

The negative-resistance magnetron has a split plate

Related questions

Description : What is the typical frequency range about the center frequency of a tunable magnetron?

Last Answer : . ±5 percent.

Description : What is the effect on magnetron operation if the magnetic field strength is too high?

Last Answer : The magnetron will not oscillate.

Description : What is the frequency range of magnetron oscillators?

Last Answer : 600-30,000 megahertz.

Description : What is the typical frequency range about the center frequency of a tunable magnetron?

Last Answer : ±5 percent.

Description : What is the effect on magnetron operation if the magnetic field strength is too high?

Last Answer : The magnetron will not oscillate.

Description : What is the frequency range of magnetron oscillators?

Last Answer : . 600-30,000 megahertz.

Description : Name the procedure used to reduce excessive arcing in a magnetron?

Last Answer : Baking in.

Description : Capacitive tuning by inserting a ring into the cavity slot of a magnetron is accomplished by what type of tuning mechanism?

Last Answer : . A cookie-cutter tuner

Description : Magnetron tuning by altering the surface-to-volume ratio of the hole portion of a hole-and-slot cavity is what type of tuning?

Last Answer : Inductive.

Description : Why is the pi mode the most commonly used magnetron mode of operation

Last Answer : Greater power output.

Description : What are the electrons called that give up energy to the ac field in a magnetron?

Last Answer : Working electrons.

Description : Why is the negative-resistance magnetron often operated with reduced filament voltage?

Last Answer : To reduce the effects of filament bombardment.

Description : What starts the oscillations in a negative-resistance magnetron?

Last Answer : The application of the proper magnetic field.

Description : A magnetron will produce oscillations when the electrons follow what type of path?

Last Answer : Circular.

Description : What element in the magnetron causes the curved path of electron flow?

Last Answer : The permanent magnet.

Description : What controls the output frequency of a magnetron?

Last Answer : . The resonant cavities.

Description : A cylindrical copper block with resonant cavities around the circumference is used as what component of a magnetron?

Last Answer : Anode or plate

Description : What serves as a grid in a magnetron?

Last Answer : A magnetic field.

Description : Draw the construction of magnetron and describe it’s working.

Last Answer : Working/Operation: 1. Now assume RF oscillations are initiated due to some noise transient within the magnetron, the oscillations will be sustained by device operation. 2. Self- ... these favored electrons imparts enough energy to the RF oscillations so that they are sustained.  

Description : Which of the following types of HPA is not used in earth stations? A. TWT B. Transistor C. Klystron D. Magnetron

Last Answer : D. Magnetron

Description : What do you call a circuit that controls the magnetron output? A. Inverter B. Impeller C. Modulator D. Converter

Last Answer : C. Modulator

Description : Low-power radar uses A. RIMPATT B. TRAPATT C. Magnetron D. IMPATT

Last Answer : D. IMPATT

Description : With neat cross sectional constructional details,write effect of magnetic and electric field in magnetron

Last Answer : 1)When magnetic & electric fields act simultaneously upon the electron,its path can have any of a number of shapes dictated by the resistive strengths of the mutually perpendicular electric & ... happens because in practice the applied magnetic field is greatly in excess of the cutoff field.

Description : What is the major difference in grid construction between power pentodes and conventional pentodes?

Last Answer : Conventional pentodes have a staggered grid arrangement, while power pentodes have a shielded grid arrangement.

Description : What is the main difference in construction between normal PN junction diodes and tunnel diodes?

Last Answer : The amount of doping.

Description : Other than the type of cell used, what is the major difference between the construction of the leadacid and nicad battery?

Last Answer : The cells in the nicad battery can be replaced.

Description : What is the basic difference between the primaries of ac and dc rate generators?

Last Answer : The method of primary excitation (ac and permanent magnet).

Description : What is the primary difference between the NPN and PNP amplifiers?

Last Answer : The polarity of the source voltage

Description : What is the primary difference between the radio horizon and the natural horizon?

Last Answer : Sea water.

Description : What is the primary difference between the pump signal of a simple parametric amplifier and the pump signal of a nondegenerative parametric amplifier?

Last Answer : The pump signal of a nondegenerative parametric amplifier is higher than twice the input signal.

Description : What is the primary difference between a diode and a triode?

Last Answer : The triode contains a third element called the control rid.

Description : What is the primary difference between the major and minor lobes of a radiation pattern?

Last Answer : Major lobes have the greatest amount of radiation.

Description : What kind of material must be used in the construction of waveguides?

Last Answer : Conductive material.

Description : What type of material is used in the construction of bolometers and thermistors?

Last Answer : Temperature-sensitive material that exhibits a large negative temperature coefficient.

Description : How do the two types of monolithic IC construction differ?

Last Answer : Diffusion penetrates substrate; epitaxial does not

Description : Name the two types of monolithic IC construction discussed.

Last Answer : Diffusion; epitaxial growth

Description : What is a major advantage of modular construction?

Last Answer : Rapid repair of systems and improved efficiency

Description : The way a magnetic head will be used determines how it is constructed. Name three factors that determine the final construction of a magnetic head.

Last Answer : a. Type of head (record, reproduce, or erase). b. Frequencies it will record or reproduce. c. Whether it will be used on a single or multitrack recorder.

Description : How can loss be reduced during construction (or fabrication) of optical fibers?

Last Answer : By removing the impurities from optical fiber.

Description : What are the basic requirements for any splice or terminal connection?

Last Answer : The connection must be both mechanically and electrically as strong as the conductor or device with which it is used

Description : The magic-T is composed of what two basic types of T junctions?

Last Answer : E-type and H-type.

Description : What are the two basic types of T junctions?

Last Answer : E-type and H-type.

Description : What are the three basic characteristics of sound

Last Answer : Pitch, intensity, and quality.

Description : What are the three basic requirements for sound?

Last Answer : A source, medium, and detector (receiver).

Description : In the basic transistor amplifier discussed earlier, what is the relationship between the polarity of the input and output signals?

Last Answer : The signals are opposite in polarity or 180 degrees out of phase with each other.

Description : Name the two basic elements of the SCLSIS program

Last Answer : Validation and updating

Description : What is the basic principle of a magnetic amplifier?

Last Answer : change in inductance in a series LR circuit causes a change in true power.

Description : The two basic types of voltage regulators are ___ and ___

Last Answer : Series and shunt.

Description : What is the most basic type of filter?

Last Answer : The capacitor filter.

Description : What are the four basic sections of a power supply?

Last Answer : Transformer, rectifier, filter, regulator.