Description : The input and output signals of a JFET amplifier have what phase relationship?
Last Answer : They are 180 degrees out of phase.
Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?
Last Answer : 800 watts.
Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?
Last Answer : Common emitter (CE) and common base (CB)
Description : Which transistor configuration provides a phase reversal between the input and output signals?
Last Answer : Common emitter.
Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?
Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.
Description : If the two input signals to a difference amplifier are equal in amplitude but neither in phase nor 180 degrees out of phase, what will the output signal be?
Last Answer : . A different shape than the input signals but larger in amplitude.
Description : If the two input signals to a difference amplifier are equal in amplitude and 180 degrees out of phase, what will the output signal be?
Last Answer : Equal in shape and frequency to each input signal and larger in amplitude by two times than
Description : . If the two input signals of a difference amplifier are in phase and equal in amplitude, what will the output signal be?
Last Answer : No output (the signals will "cancel out").
Description : What is the relationship between the polarity of the voltage applied to the PNP transistor and that applied to the NPN transistor?
Last Answer : The polarity of voltage applied to the PNP transistor is opposite of that applied to the NPN
Description : To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?
Last Answer : Positive, more positive.
Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal
Last Answer : B) Clipping of output in the positive half of the input signal
Description : What is used to bias a magnetic amplifier so that the control winding remains free to accept control (input) signals?
Last Answer : A bias winding and associated circuitry.
Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?
Last Answer : Local oscillator and coherent oscillator.
Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.
Last Answer : Answer: D
Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?
Last Answer : 200 millivolts. A-18. a. Differential amplifier
Description : If only one input signal is used with a difference amplifier, what will the output signal be?
Last Answer : Equal in shape and frequency to the input signal; larger in amplitude than the input signal; half as large in amplitude as when two input signals were used that were 180 degrees out of phase.
Description : If If the input signals are 180 degrees out of phase with each other and a combined output is taken between the two output terminals, what will the amplitude of the combined output signal be?
Last Answer : 200 millivolts.
Description : If the input signals are 180 degrees out of phase with each other, what will be the peak-to-peak amplitude of the output signals?
Last Answer : Each output signal will be 100 millivolts.
Description : If the input signals are in phase, what will be the peak-to peak amplitude of the output signals?
Last Answer : 0 volts (the input signals will "cancel out").
Description : In the illustration, the function generators will accept only a signal of a given polarity, if negative is used for ahead and positive for astern, moving the bridge reference in the direction ... cause a speed change until the output voltage exceeds the value of the lube oil pressure override
Last Answer : Answer: C
Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage
Last Answer : Answer: B
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Description : What are the factors that limit the frequency response of a transistor amplifier?
Last Answer : The capacitance and inductance of the circuit and the interelectrode capacitance of the transistor.
Description : What are the four classes of operation of a transistor amplifier?
Last Answer : A, AB, B, C.
Description : A negative damper with negative bias clamps the most positive extremity of the output wave shape to what polarity (positive or negative)?
Last Answer : Negative potential.
Description : To which polarity does a positive damper with positive bins clamp the most negative extremity of the output waveform (positive or negative)?
Last Answer : Positive potential.
Description : What impedance relationship between the output of one circuit and the input of another circuit will provide the maximum power transfer?
Last Answer : Equal impedance.
Description : Which transistor configuration has the highest input resistance?
Last Answer : Common collector.
Description : What are the three basic configurations of transistor oscillators?
Last Answer : Common collector (CC), common emitter (CE), and common base (CB).
Description : What components form the input-signal-developing impedance for the amplifier?
Last Answer : C2 and the secondary of T1.
Description : If the input-signal-developing impedance of an amplifier is increased, what is the effect on the gain?
Last Answer : The gain increases.
Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?
Last Answer : 0 volts.
Description : In a nondegenerative parametric amplifier the difference between the input frequency and the pump frequency is called what?
Last Answer : Idler- or lower-sideband frequency.
Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?
Last Answer : Exactly double the input frequency.
Description : Does an amplifier actually change an input signal? Why or why not?
Last Answer : No, the input signal is unchanged, the output signal is controlled by the input signal but does not effect the actual input signal.
Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor
Description : Draw: (i) Input characteristics of transistor in CE mode. (ii) Output characteristics of transistor in CE mode and show different regions on it.
Last Answer : (i) Input characteristics of transistor in CE mode. (ii) Output characteristics of transistor in CE mode and show different regions on it.
Description : Two tape recorders have signal-to-noise ratios (SNRs) of 25-dB RMS and 35-dB RMS respectively. Which of the SNRs can record and reproduce the widest range of input signals and why?
Last Answer : 35-dB RMS because the highest SNR can always record and reproduce the widest range of input signals.
Description : If C4 were removed from the circuit, what would happen to the output of the amplifier?
Last Answer : The output would decrease. (C4 decouples R2 preventing degenerative feedback from R2.)
Description : If the output impedance of an amplifier circuit is decreased, what is the effect on the gain?
Last Answer : The gain decreases.
Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?
Last Answer : A step-down transformer.
Description : What type coupling is usually used to couple the output from a power amplifier?
Last Answer : Transformer coupling.
Description : What is the basic principle of a magnetic amplifier?
Last Answer : change in inductance in a series LR circuit causes a change in true power.
Description : What the three basic components make up the typical magnetic amplifier?
Last Answer : Two saturable reactors and a transformer.
Description : An amplifier is said to suffer from distortion when its output is - (1) low (2) different from input (3) noisy (4) larger than its input
Last Answer : (3) noisy Explanation: Amplifier Distortion can take on many forms such as Amplitude, Frequency and Phase Distortion due to Clipping. For a signal amplifier to operate correctly without any distortion to the output signal, it requires some form of DC Bias on its Base or Gate terminal.
Description : An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes _____________. A. 5 volts, the output changes 10 volts B. 10 volts, the output changes 5 volts C. 2 volts, the output changes 10 volts D. 10 volts, the output changes 2 volts
Description : When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly? A. 32 volts B. 30 volts C. 28 volts D. 15 volts
Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC
Last Answer : Answer: A
Description : An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by ______________. A. 1 volt, the output changes 5 volts B. 5 volts, the output changes 1 volt C. 5 volts, the output changes 10 volts D. 10 volts, the output changes 5 volts