The purpose of connecting a capacitor in fluorescent tube circuit is

The purpose of connecting a capacitor in fluorescent tube circuit is

• To increase switching on time

• To decrease switching off time

• To increase power factor

• To decrease power consumption
by

1 Answer

Answer :

The purpose of connecting a capacitor in fluorescent tube circuit is To increase power factor

by

Related questions

The purpose of a choke in a fluorescent tube is

Description : The purpose of a choke in a fluorescent tube is (A) To decrease the current (B) To increase the current (C) To decrease the voltage momentarily (D) To increase the voltage momentarily

Last Answer : The purpose of a choke in a fluorescent tube is To increase the voltage momentarily

Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Description : Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Last Answer : Power factor of an inductive circuit is usually improved by connecting capacitor to it in parallel.

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Which is printed on a commonly used fluorescent tube light?

Description : Which is printed on a commonly used fluorescent tube light?

Last Answer : – 6500 k

A common fluorescent tube contains (a) sodium vapour (b) argon at low pressure (c) mercury vapour at low pressure (d) mercuric oxide and neon

Description : A common fluorescent tube contains (a) sodium vapour (b) argon at low pressure (c) mercury vapour at low pressure (d) mercuric oxide and neon

Last Answer : Ans:(c)

The radiation initially produced in fluorescent tube is – (1) infrared (2) ultraviolet (3) microwaves (4) X-rays

Description : The radiation initially produced in fluorescent tube is – (1) infrared (2) ultraviolet (3) microwaves (4) X-rays

Last Answer : (2) ultraviolet Explanation: The primary radiation that is initially produced within a fluorescent lamp is analogous to that emitted by a low pressure mercury lamp. Fluorescent lamps produce UV radiation by ... coating on the inside of the tubes absorbs the UV and converts it to visible light.

Which is printed on a commonly used fluorescent tube light?

Description : Which is printed on a commonly used fluorescent tube light?

Last Answer : 6500 k

Luminance efficiency is minimum for a a. Fluorescent tube b. High wattage light bulb c. Mercury vapor lamp d. Low wattage light bulb

Description : Luminance efficiency is minimum for a a. Fluorescent tube b. High wattage light bulb c. Mercury vapor lamp d. Low wattage light bulb

Last Answer : d. Low wattage light bulb

Luminous efficiency is least for a A. mercury vapor lamp B. low-wattage light bulb C. high-wattage light bulb D. fluorescent tube

Description : Luminous efficiency is least for a A. mercury vapor lamp B. low-wattage light bulb C. high-wattage light bulb D. fluorescent tube

Last Answer : B. low-wattage light bulb

Working of the Fluorescent Tube Light

Description : Working of the Fluorescent Tube Light

Last Answer : The fluorescent lamp circuit consists of a choke, a starter, a fluorescent tube and a frame. The length of the commonly used fluorescent tube is 100 cm; its power rating is 40 W ... momentary high voltage surge across the two filaments. Ionization takes place through argon and produces bright light.

Which is printed on a commonly used fluorescent tube ligh

Description : Which is printed on a commonly used fluorescent tube ligh

Last Answer : 6500

Luminance efficiency is minimum for a ∙ a. Fluorescent tube ∙ b. High wattage light bulb ∙ c. Mercury vapor lamp ∙ d. Low wattage light bulb

Description : Luminance efficiency is minimum for a ∙ a. Fluorescent tube ∙ b. High wattage light bulb ∙ c. Mercury vapor lamp ∙ d. Low wattage light bulb

Last Answer : d. Low wattage light bulb

The radiation initially produced in fluorescent tube is (1) infrared (2) ultraviolet (3) microwaves (4) X-rays

Description : The radiation initially produced in fluorescent tube is (1) infrared (2) ultraviolet (3) microwaves (4) X-rays

Last Answer : ultraviolet

Fluorescent Tube Practical

Description : Fluorescent Tube Practical

Last Answer : Practical Significance Fluorescent tubes are widely used in residential, commercial and industrial installation for illumination. Therefore, wiring, testing and fault finding of fluorescent tube is important. ... does not glow, turn the rod properly and fix the starter properly in holder.

The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within the envelope C. counteract the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Description : The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within ... the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Last Answer : Answer: A

What is the purpose of a capacitor in an AC circuit?

Description : What is the purpose of a capacitor in an AC circuit?

Last Answer : Every AC supply is not ideal AC it contains DC component so to provide restriction to DC component in supply we have to use Capacitor

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Description : The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Last Answer : (2) to decrease the current flow Explanation: The choke primarily serves to limit current flow to the correct level for the tube. It also can be used during startup to provide an inductive 'kick' forming a momentary highervoltage pulse to start the lamp.

The purpose of choke in a fluorescent lamp is

Description : The purpose of choke in a fluorescent lamp is

Last Answer : to decrease the flow of current

The purpose of choke in a fluorescent lamp is : (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) ro decrease the voltage momentarily

Description : The purpose of choke in a fluorescent lamp is : (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) ro decrease the voltage momentarily

Last Answer :  to decrease the current flow

When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, causing glass to fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Description : When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, ... fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Last Answer : Answer: D

The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Description : The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Last Answer : Answer: B

The purpose of a coupling capacitor in an amplifier is to:

Description : The purpose of a coupling capacitor in an amplifier is to:  (1) Control the output (2) Provide impedance matching (3) Provide DC isolation between amplifier and load (4) W Increase the bandwidth

Last Answer : The purpose of a coupling capacitor in an amplifier is to: Provide DC isolation between amplifier and load.

When an alternating potential is applied to a capacitor, the current in the circuit will

Description : When an alternating potential is applied to a capacitor, the current in the circuit will  1. lead the applied potential 2. lag the applied potential 3. be in phase with the applied potential 4. none 

Last Answer : When an alternating potential is applied to a capacitor, the current in the circuit will lead the applied potential

For a DC circuit capacitor is

Description : For a DC circuit capacitor is

Last Answer : For a DC circuit capacitor is virtually an open circuit

A circuit requires a capacitor of 100pf, 25V. The capacitor can be:

Description : A circuit requires a capacitor of 100pf, 25V. The capacitor can be:  (1) Paper capacitor (2) Electrolytic capacitor  (3) Ceramic capacitor (4) Any type of capacitor

Last Answer : A circuit requires a capacitor of 100pf, 25V. The capacitor can be: Electrolytic capacitor.

Mention the precautions to be taken while connecting CT and PT in the circuit.

Description : Mention the precautions to be taken while connecting CT and PT in the circuit. 

Last Answer : Precautions to be taken while using instrument transformers: 1. Secondary of CT is never kept open circuited when it is energized. 2. Secondary of PT is never kept short circuited when it ... of the instrument transformers unless they are properly grounded. 8. Never connect to DC circuits.

What should be observed when connecting a voltmeter into a DC circuit?

Last Answer :  What should be observed when connecting a voltmeter into a DC circuit? A.  rms B.  resistance C.  polarity D.  power factor

The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The 'Choke' used with a tube light is basically – (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : (1) an inductor Explanation: In electronics, a choke is an inductor used to block higher-frequency alternating current (AC) in an electrical circuit, while passing lower-frequency or direct ... created by suddenly interrupting the current in choke, which is connected in series with the tubelight.

A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two back-to-back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Description : A triac thyristor functions as a control device and is basically ________________. A. two NPN transistors in parallel with a common base lead B. a diode in series with a temperature sensitive capacitor C. two ... -back SCR's with a common gate lead D. a triode tube with an extra heavy grid element

Last Answer : Answer: C

The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Description : The ‘Choke’ used with a tube light is basically (1) an inductor (2) a capacitor (3) a transformer (4) a resistor

Last Answer : an inductor

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B

What is the purpose of the synchro capacitor?

Description : What is the purpose of the synchro capacitor?

Last Answer : To improve overall synchro system accuracy by reducing stator currents.

What is the purpose of connecting external resistors to slip ring Induction motor?

Description : What is the purpose of connecting external resistors to slip ring Induction motor?

Last Answer : It increases starting torque and decreases starting current.

What is purpose of connecting thyristor bridges in parallel?

Description : What is purpose of connecting thyristor bridges in parallel?

Last Answer : Thyristor bridges are connected in parallel to improve current rating.  

In the circuit shown in the figure, the capacitor C is charged to a potential Vo. The heat generated in the circuit when the switch S is closed, is

Description : In the circuit shown in the figure, the capacitor C is charged to a potential Vo. The heat generated in the circuit when the switch S is closed, is

Last Answer : In the circuit shown in the figure, the capacitor C is charged to a potential Vo. The heat generated in the circuit when ... )^(2)` D. `8 CV _(0)^(2)`

In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is decreasing at a rate of `sqrt5 C//s` Choose the corr

Description : In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is decreasing at a rate of `sqrt5 C//s` Choose the corr

Last Answer : In an L-C circuit shown in figure C=1F, L=4H At time t=0, charge in the capacitor is 4C and it is ... a and b are correct D. Both a and b are wrong

In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 C` and it is decreasing at the rate of `sqrt(5)

Description : In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 C` and it is decreasing at the rate of `sqrt(5)

Last Answer : In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 ... ))` C. `2tan^(-1)((2)/(3)) D. None of these

In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 C` and it is decreasing at the rate of `sqrt(5)

Description : In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 C` and it is decreasing at the rate of `sqrt(5)

Last Answer : In an `LC` circuit shows in Fig. `C = 1 F`, `L = 4 H`. At time `t = 0`, charge in the capacitor is `4 ... statement. A. 6 C B. 8 C C. 10 C D. 12 C

An L-C circuit contains a 0.60 H inductor and a `25muF` capacitor is `3.0xx10^(-5)C?`

Description : An L-C circuit contains a 0.60 H inductor and a `25muF` capacitor is `3.0xx10^(-5)C?`

Last Answer : An L-C circuit contains a 0.60 H inductor and a `25muF` capacitor is `3.0xx10^(-5)C?`

What is the capacitive resistance of a 0.04 microfarad capacitor in ac circuit that has a frequency of 1000 hz?

Description : What is the capacitive resistance of a 0.04 microfarad capacitor in ac circuit that has a frequency of 1000 hz?

Last Answer : The capacitive reactance is approximately 4 kΩ .

Which of the device is employed in substation to limit the short circuit current in the power system: a) Shunt condenser b) Reactor c) Series capacitor d) Shunt capacitor

Description : Which of the device is employed in substation to limit the short circuit current in the power system: a) Shunt condenser b) Reactor c) Series capacitor d) Shunt capacitor

Last Answer : Ans: B

A capacitor (condenser) is used in an electrical circuit to (a) step down voltage (b) step up voltage (c) store electric charge (d) produce electric charge

Description : A capacitor (condenser) is used in an electrical circuit to (a) step down voltage (b) step up voltage (c) store electric charge (d) produce electric charge

Last Answer : Ans:(c)

In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes more efficient at lower capacitance. C. the arrangement allows the coupling of the signal while it isolates the biasing of each stage. D. good frequency response.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Last Answer : Answer: A

What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad

Description : What is the value of the capacitor in the astern valve position circuit shown in the illustration? EL-0099 A. 100 kFarad B. 0.5 microfarad C. 0.5 millifarad D. 50 kFarad

Last Answer : Answer: B

In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Last Answer : Answer: D

When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment away. B. Measure capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Description : When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment ... capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Last Answer : Answer: C