Mention the precautions to be taken while connecting CT and PT in the circuit.

Mention the precautions to be taken while connecting CT and PT in the circuit. 
by

1 Answer

Answer :

Precautions to be taken while using instrument transformers: 1. Secondary of CT is never kept open circuited when it is energized. 2. Secondary of PT is never kept short circuited when it is energized. 3. Power fuses must be connected in the primary circuit of PT. 4. Always ground the metallic cases of instrument transformers. 5. Secondaries should be grounded close to the transformer. 6. When secondaries of transformers are interconnected there should be only one grounded point. 7. Do not touch the leads of terminals of the instrument transformers unless they are properly grounded. 8. Never connect to DC circuits.

by

Related questions

Write any four differences between CT and PT.

Description : Write any four differences between CT and PT.

Last Answer : CT PT CT corresponds to current transformer PT corresponds to potential transformer CT primary is connected in series with load and secondary winding is connected to a low range ammeter. PT ... ) x PT ratio It is a step-up transformer. It is a step-down transformer

List out the precautions to be taken while charging of lead- acid battery

Description : List out the precautions to be taken while charging of lead- acid battery 

Last Answer : precautions to be taken while charging of lead- acid battery: 1) Never keep the battery in the circuit and connect for external charging if it is not designed so. 2) While disconnecting / removing a ... tools etc on batteries. 10) Do not splash any liquids on the batteries, near the charger etc.

Why CT is never operated with an open secondary ?

Description : Why CT is never operated with an open secondary ?

Last Answer : CT secondary should never be kept open because it will cause saturation of the core to a high level and very high voltage will appear across the secondary which can breakdown the insulation. One terminal of PT secondary is always grounded to avoid capacitive induction and for human safety

If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug

Description : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be

Last Answer : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Description : Power factor of an inductive circuit is usually improved by connecting capacitor to it in?

Last Answer : Power factor of an inductive circuit is usually improved by connecting capacitor to it in parallel.

Time constant of a circuit is the time in seconds taken after the application of voltage to each?

Description : Time constant of a circuit is the time in seconds taken after the application of voltage to each?

Last Answer : Time constant of a circuit is the time in seconds taken after the application of voltage to each 63% of maximum value.

Briefly explain how the power factor of an inductive circuit can be improved.

Description : Briefly explain how the power factor of an inductive circuit can be improved.

Last Answer : As we know that power factor should be corrected to ensure that the current supplied is cost friendly. Meaning the power factor should be around one but not greater than one(0.8-0.9) in a ... an inductive circuit due to the inductive reactance which oppose the change of current in the ac circuit. 

Time constant of a capacitive circuit

Last Answer : It is denoted as τ, tau and has the value of 1/RC. We

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

State Ohm’s law for electric circuit.

Description : State Ohm’s law for electric circuit.

Last Answer : Ohms law -States that the current flows in a circuit is directly proportional to the applied voltage (V) and inversely the proportional resistance provided with the temperature main constant

Define active circuit and passive circuit.

Description : Define active circuit and passive circuit.

Last Answer : Active circuit: Active Circuit is one which contains at least one source of e.m.f. or energy, is called active circuit.  Passive Circuit: Passive Circuit is one which does not contain any source of e.m.f. or energy in it, is called passive circuit.

Basic Circuit Elements

Description : Basic Circuit Elements

Last Answer : Resistance ,current,voltage

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Compare combinational logic circuit and sequential logic circuit

Description : Compare combinational logic circuit and sequential logic circuit

Last Answer : Combinational logic Sequential logic The combinational logic circuit consists of logic gate only Sequential logic circuit consists of combinational logic circuit along with memory for storage of ... , multiplexer, demultiplexer etc E.g. counters, shift registers flip-flop etc

What is unilateral and bilateral circuit?

Description : What is unilateral and bilateral circuit?

Last Answer : Unilateral Circuit: If the characteristic (response or behavior) of circuit depends on the direction of flow of current through its elements, then the network is called as a unilateral network.  ... the direction of current through its elements, then the network is called as a bilateral network.

Describe the difference between an open circuit and a short circuit.

Description : Describe the difference between an open circuit and a short circuit.

Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

Series circuit rules

Description : Series circuit rules

Last Answer : Series circuit rules

Parallel rc circuit

Description : Parallel rc circuit

Last Answer : Parallel rc circuit

Parallel circuit rules

Description : Parallel circuit rules

Last Answer : Parallel circuit rules

Source free RL circuit 8

Description : Source free RL circuit 8

Last Answer : Source free RL circuit 8

Source free RL circuit 7

Description : Source free RL circuit 7

Last Answer : Source free RL circuit 7

Source free RL circuit 6

Description : Source free RL circuit 6

Last Answer : Source free RL circuit 6

Source free RC circuit 2

Description : Source free RC circuit 2

Last Answer : Source free RC circuit 2

Source free RC circuit 3

Description : Source free RC circuit 3

Last Answer : Source free RC circuit 3

Source free RC circuit 4

Description : Source free RC circuit 4

Last Answer : Source free RC circuit 4

Source free RC circuit 5

Description : Source free RC circuit 5

Last Answer : Source free RC circuit 5

Source free RC circuit 6

Description : Source free RC circuit 6

Last Answer : Source free RC circuit 6

Source free RC circuit 7

Description : Source free RC circuit 7

Last Answer : Source free RC circuit 7

Source free RC circuit 8

Description : Source free RC circuit 8

Last Answer : Source free RC circuit 8

Source free RL circuit 1

Description : Source free RL circuit 1

Last Answer : Source free RL circuit 1

Source free RL circuit 2

Description : Source free RL circuit 2

Last Answer : Source free RL circuit 2

Source free RL circuit 3

Description : Source free RL circuit 3

Last Answer : Source free RL circuit 3

Source free RL circuit 4

Last Answer : Source free RL circuit 4

Source free RL circuit 5

Last Answer : Source free RL circuit 5

State maximum power transfer theorem for DC circuit.

Description : State maximum power transfer theorem for DC circuit.

Last Answer : Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal ... removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

List any two methods of reactive power measurement in 3 phase circuit.

Description : List any two methods of reactive power measurement in 3 phase circuit.

Last Answer : Methods of reactive power measurement in 3 phase circuit: (i) Two single phase wattmeter method (ii) One single phase wattmeter method

Define balanced and unbalanced load in three phase circuit.

Description : Define balanced and unbalanced load in three phase circuit.

Last Answer : Balanced Load: When all the imedances of 3 phases are equal in magnitude and of same nature then load is said to be balanced.  Unbalanced Load: When all the imedances of 3 phases are not equal in magnitude and of different nature then load is said to be unbalanced.

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

Draw and explain Hartley Oscillator circuit diagram.

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-  

Define- (i) Node (ii) Loop for a DC circuit

Description : Define- (i) Node (ii) Loop for a DC circuit

Last Answer : Ans: i) Node: A point or junction at which two or more elements of network are connected is called as node. ii) Loop: A closed path for flow of current in an electrical circuit is called loop.

Compare electric and magnetic circuit.

Description : Compare electric and magnetic circuit.

Last Answer : Comparison between Magnetic and Electric Circuits

Draw a typical electric circuit including ammeter and voltmeter.

Description : Draw a typical electric circuit including ammeter and voltmeter.

Last Answer : The figure shows typical electric circuit including ammeter and voltmeter. Ammeter is connected in series for measurement of current. Voltmeter is connected in parallel for measurement of voltage. Fuse is use ... are used. If the electric supply is DC the DC ammeter and DC voltmeter are used.

In a series R-C circuit, with the increase in frequency, current

Description : In a series R-C circuit, with the increase in frequency, current (A) Reduces (B) Increases (C) Does not change (D) Becomes zero

Last Answer : In a series R-C circuit, with the increase in frequency, current Increases

For a DC circuit capacitor is

Description : For a DC circuit capacitor is

Last Answer : For a DC circuit capacitor is virtually an open circuit

A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are

Description : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is

Last Answer : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is 500 Hz

Breaking capacity of a circuit breaker is usually expressed in terms of

Description : Breaking capacity of a circuit breaker is usually expressed in terms of  (1) Ampere (2) Volts (3) MW (4) MVA

Last Answer : Breaking capacity of a circuit breaker is usually expressed in terms of MVA

Which of the following is used in a circuit breaker as the medium in which the arc forms?

Description : Which of the following is used in a circuit breaker as the medium in which the arc forms? A) Insulating gas B) Insulating oil C) Vacuum D) All the above

Last Answer : Which of the following is used in a circuit breaker as the medium in which the arc forms? A) Insulating gas B) Insulating oil C) Vacuum D) All the above

Magnetic circuit breakers use _________

Description : Magnetic circuit breakers use _________ A) Permanent magnets B) Earth magnets C) Solenoid D) All the above

Last Answer : Magnetic circuit breakers use Solenoid 

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively?

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______

Description : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these

Last Answer : A circuit that binds the upper or lower extreme of a waveform to a fixed DC voltage level is called ______ A) DC voltage restorer B) Clamping circuit C) Both A and B D) None of these