The electron beam in a CRT is made to sweep from left to right across the screen. What tube element causes this sweeping motion?

The electron beam in a CRT is made to sweep from left to  right across the screen. What tube element causes this  sweeping motion?
by

1 Answer

Answer :

The horizontal-deflection plate.
by

Related questions

What type of deflection is preferred for a crt electron beam?

Description : What type of deflection is preferred for a crt electron beam?

Last Answer : . Electromagnetic.

What term is used for the ability of a spot on a CRT screen to continue to glow after the electron bean has struck it and moved away?

Description : What term is used for the ability of a spot on a CRT screen to continue to glow after the electron bean has struck it and moved away?

Last Answer : Persistence.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.

Type of waveform generated by the sweep generator of the CRT

Description : Type of waveform generated by the sweep generator of the CRT

Last Answer : sawtooth

How is the electron beam of a three-cavity klystron accelerated toward the drift tube?

Description : How is the electron beam of a three-cavity klystron accelerated toward the drift tube?

Last Answer : A large negative pulse is applied to the cathode.

Which of the following statement(s) is/are correct? (1) Persistence is the term used to describe the duration of phosphorescence. (2) The control electrode is used to turn the electron beam on and off. (3) The electron gun creates a source of electrons which are focussed into a narrow beam directed at the face of CRT. (4) All of the above.

Description : Which of the following statement(s) is/are correct? (1) Persistence is the term used to describe the duration of phosphorescence. (2) The control electrode is used to turn the electron beam on and off. (3) ... which are focussed into a narrow beam directed at the face of CRT. (4) All of the above. 

Last Answer : All of the above.

Scopes that produce two channels on a single CRT with a single beam are referred to as what types of scopes?

Description : Scopes that produce two channels on a single CRT with a single beam are referred to as what types of scopes?

Last Answer : Dual-trace oscilloscopes.

Which of the following is not a part of a CRT? (1) Phosphor screen (2) Shadow mask (3) Electron gun (4) Gas plasma

Description : Which of the following is not a part of a CRT? (1) Phosphor screen (2) Shadow mask (3) Electron gun (4) Gas plasma

Last Answer : (4) Gas plasma Explanation: The cathode ray tube (CRT) is a vacuum tube containing an electron gun (a source of electrons or electron emitter) and a fluorescent screen used to view images. Colour tubes ... stripes (as in aperture grille designs) or clusters called "triads" (as in shadow mask CRTs).

Which of the following is/are the components of a CRT ? (a) Electron Gun (b) Control Electrode (c) Focusing Electrode (d) Phosphor Coated Screen Codes : (A) (a) and (d) (B) (a), (b) and (d) (C) (a), (b), (c) and (d) (D) (a), (c) and (d)

Description : Which of the following is/are the components of a CRT ? (a) Electron Gun (b) Control Electrode (c) Focusing Electrode (d) Phosphor Coated Screen Codes : (A) (a) and (d) (B) (a), (b) and (d) (C) (a), (b), (c) and (d) (D) (a), (c) and (d) 

Last Answer : (C) (a), (b), (c) and (d)

Which of the following is not a part of a CRT ? (1) Phosphor screen (2) Shadow mask (3) Electron gun (4) Gas plasma

Description : Which of the following is not a part of a CRT ? (1) Phosphor screen (2) Shadow mask (3) Electron gun (4) Gas plasma

Last Answer : Gas plasma

What CRT element provides for controls of the number of electrons passing father into the tube?

Description : What CRT element provides for controls of the number of electrons passing father into the tube?

Last Answer : control grid

What precautions must be taken when sweeping a transmitting antenna?

Description : What precautions must be taken when sweeping a transmitting antenna?

Last Answer : You must ensure that power induced from any adjacent transmitting antennas does not damage your test equipment.

How are you faring if you’re in the path of this huge, awful, snow/ice juggernaut that is sweeping across the country?

Description : How are you faring if you’re in the path of this huge, awful, snow/ice juggernaut that is sweeping across the country?

Last Answer : It started snowing in the early morning and will continue all day. The ice that was supposed to be underneath all this never materialized so there were just a few accidents during the morning commute. ... a freight train throwing the snow piles several yards off the road . We love our plow guys!

I heard of an invading, vanquishing army sweeping across the land, liquid-quick; conquering everything, quelling resistance. With it came darkness, dimming the light. Humans hid in their houses, while outside spears pierced, shattering stone walls. Uncountable soldiers smashed into the ground, but each elicited life as he died; when the army had vanished, advancing northward, the land was green and growing, refreshed. What is it? -Riddles

Description : I heard of an invading, vanquishing army sweeping across the land, liquid-quick; conquering everything, quelling resistance. With it came darkness, dimming the light. Humans hid in their houses, while ... vanished, advancing northward, the land was green and growing, refreshed. What is it? -Riddles

Last Answer : A rainstorm.

What element in the magnetron causes the curved path of electron flow?

Description : What element in the magnetron causes the curved path of electron flow?

Last Answer : The permanent magnet.

Final duties of the HAS before quitting office a) Should carefully examine each sorting compartment to see that no article are left in it unsorted b) The sweeping, used labels, broken seal etc are personally examined c) The articles of stationary, stamps, seals and books etc are carefully placed in the portfolio. d) All the above

Description : Final duties of the HAS before quitting office a) Should carefully examine each sorting compartment to see that no article are left in it unsorted b) The sweeping, used labels, broken seal etc are ... stationary, stamps, seals and books etc are carefully placed in the portfolio. d) All the above

Last Answer : d) All the above

The range sweep in a range-gate generator is started at the same time as what other pulse?

Description : The range sweep in a range-gate generator is started at the same time as what other pulse?

Last Answer : Transmitter.

What effect does closer spacing of plates have on the electron beam?

Description : What effect does closer spacing of plates have on the electron beam?

Last Answer : A greater deflection angle.

What effect does closer spacing of plates have on the electron beam?

Description : What effect does closer spacing of plates have on the electron beam?

Last Answer : A greater deflection angle.

What effect do longer deflection plates have on the electron beam?

Description : What effect do longer deflection plates have on the electron beam?

Last Answer : A greater deflection angle.

What relationship must exist between the electron beam and the traveling wave for bunching to occur in the electron beam of a twt?

Description : What relationship must exist between the electron beam and the traveling wave for bunching to occur in the electron beam of a twt?

Last Answer : The traveling wave must have a forward velocity equal to or less than the speed of the electrons in the beam.

What circuit functions does the tube in a gated-beam detector serve?

Description : What circuit functions does the tube in a gated-beam detector serve?

Last Answer : Limits, detects, and amplifies.

Which of the two types of electron motion (orbital movement and electron spin) is more important in the explanation of magnetism?

Description : Which of the two types of electron motion (orbital movement and electron spin) is more important in the explanation of magnetism?

Last Answer : Electron spin.

Beam-penetration and shadow-mask are the two basic techniques for producing color displays with a CRT. Which of the following is not true ? I. The beam-penetration is used with random scan monitors. II. Shadow-mask is used in raster scan systems. III. Beam-penetration method is better than shadow-mask method. IV. Shadow-mask method is better than beam-penetration method. (A) I and II (B) II and III (C) III only (D) IV only

Description : Beam-penetration and shadow-mask are the two basic techniques for producing color displays with a CRT. Which of the following is not true ? I. The beam-penetration is used with random scan monitors. II. Shadow-mask is used ... -penetration method. (A) I and II (B) II and III (C) III only (D) IV only

Last Answer : (C) III only

State one requirement of an electron tube, which does not exist for semiconductors, that makes the tube less efficient than the semiconductor.

Description : State one requirement of an electron tube, which does not exist for semiconductors, that makes the tube less efficient than the semiconductor.

Last Answer : The electron tube requires filament or heater voltage, whereas the semiconductor device does not; consequently, no power input is spent by the semiconductor for conduction.

In an electron tube regulator, the electron tube replaces what component?

Description : In an electron tube regulator, the electron tube replaces what component?

Last Answer : Variable resistor.

What is the most accurate method of determining the condition of an electron tube?

Description : What is the most accurate method of determining the condition of an electron tube?

Last Answer : Testing the tube in its circuit

What is the most common cause of electron tube failure?

Description : What is the most common cause of electron tube failure?

Last Answer : Open filaments

The CRT display is made up of small picture element called: a) Columns b) Pixels c) Rows d) None of These

Description : The CRT display is made up of small picture element called: a) Columns b) Pixels c) Rows d) None of These

Last Answer : b) Pixels

When the vertical input is 0V, the electron beam may be position at the __ of the screen.

Description : When the vertical input is 0V, the electron beam may be position at the __ of the screen.

Last Answer : vertical center

The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the

Description : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating anode voltage is reduced to half of ... on the screen would become (A) 64 mm (B) 32 mm (C) 8 mm (D) 1 mm

Last Answer : The vertical deflection of an electron beam on the screen of a CRO is measured to be 8 mm. Now, the potential difference between the Y-plates is doubled, and simultaneously the pre-accelerating ... of its previous value. Then, the vertical deflection of the beam on the screen would become 32 mm

What are the three main parts of CRT?

Description : What are the three main parts of CRT?

Last Answer : a. Electron gun. b. Deflection system

What is the unique ability of the CRT?

Description : What is the unique ability of the CRT?

Last Answer : To visually display electronic signals.

Flat panel displays are designed to reduce what problem of a crt display?

Description : Flat panel displays are designed to reduce what problem of a crt display?

Last Answer : Reduce the depth of the crt display caused by the length of the tube.

On the CRT display, what information is displayed in Quadrant 4?

Description : On the CRT display, what information is displayed in Quadrant 4?

Last Answer : Positive voltage (+V) and negative current ( −I).

What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Description : What is the effect upon an electron that enters the buncher gap when the potential across the grids is at 0 volts?

Last Answer : There is no effect

What effect does the shielding of the screen grid by the control grid have on plate current in beam-forming tetrodes?

Description : What effect does the shielding of the screen grid by the control grid have on plate current in beam-forming tetrodes?

Last Answer : By increasing the number of electrons that reach the plate, plate current is increased.

What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting on the left c. Pinpoint 10° segments of the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Description : What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting ... the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Last Answer : c. Pinpoint 10° segments of the sky and confirm before passing onto another

What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting on the left c. Pinpoint 10° segments of the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Description : What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting ... the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Last Answer : c. Pinpoint 10° segments of the sky and confirm before passing onto another

What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting on the left c. Pinpoint 10° segments of the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Description : What visual technique should be used when searching for an aircraft? a. Sweep from side to side with the eyes covering the whole field of vision b. Search the sky portion by portion starting ... the sky and confirm before passing onto another d. Use a succession of small and rapid eye movements

Last Answer : c. Pinpoint 10° segments of the sky and confirm before passing onto another

How does a "CRT storage tube" work?

Description : How does a "CRT storage tube" work?

Last Answer : Part of the answer is based upon the secondary emission of electrons from the phosphor screen itself from a related link. Regular CRTs drain the electron beam current off quickly so after ... their neighbors back and forth within localized area where the pattern was drawn by the electrons.

CRT stands for: a) Ctrl, Refresh, Tab b) Cathode Ray Tube c) Catholic Ray Tuber d) None of These

Description : CRT stands for: a) Ctrl, Refresh, Tab b) Cathode Ray Tube c) Catholic Ray Tuber d) None of These

Last Answer : b) Cathode Ray Tube

CRT stands for: a) Compact Ray Tube b) Cathode Ray Tube c) Compatible Recognition Tool d) None of These

Description : CRT stands for: a) Compact Ray Tube b) Cathode Ray Tube c) Compatible Recognition Tool d) None of These

Last Answer : b) Cathode Ray Tube

CRT stands for: a. Cathode ray tube b. Compared ray tube c. Command ray tube d. None of these

Description : CRT stands for: a. Cathode ray tube b. Compared ray tube c. Command ray tube d. None of these

Last Answer : a. Cathode ray tube

An ac voltage is applied across a diode. The tube will conduct when

Description : An ac voltage is applied across a diode. The tube will conduct when

Last Answer : Positive.

Is there a way to fix a deep scratch in a CRT tv screen?

Description : Is there a way to fix a deep scratch in a CRT tv screen?

Last Answer : there isint a way sorry

Why should I switch from using my normal CRT screen to an LCD screen?

Description : Why should I switch from using my normal CRT screen to an LCD screen?

Last Answer : LCD monitors are aesthetically very pleasing to the eye being slim and stylish. There is no comparison with the CRT here. LCD monitors are extremely economical when it comes to power consumption. ... hands down in this department. They offer almost twice the brightness compared to the CRT monitor.

Draw the construction of CRT. Write two materials used for CRT display screen.

Description : Draw the construction of CRT. Write two materials used for CRT display screen. 

Last Answer : Two materials used for CRT display screen: The role of this part is to display where the electrons are hitting the CRT. It is a screen coated with a material that emits light when struck by electrons. Zinc sulphide or Phosphorus are two commonly used materials. 

If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of

Description : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is   (a) 33.2 V/cm (b) 0.03 cm/V (c) 66.4 V/cm (d) 0.015 cm/V

Last Answer : If the distance of screen from a CRT to center of deflection plates is 15 cm, the length of deflection plates is 2 cm, the distance between the plates is 1 cm and accelerating voltage is 500 V, deflection sensitivity is 0.03 cm/V

What element is controlled to focus the beam?

Description : What element is controlled to focus the beam?

Last Answer : The first anode.