Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding
Last Answer : Answer: B
Description : What precaution should you take when substituting a synchro tester in a circuit for a transmitter?
Last Answer : Use only one receiver so as not to overload the tester.
Description : Which of the two synchro designation codes is indicated by 5DG on a synchro nameplate?
Last Answer : The Navy prestandard designation code.
Description : When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?
Last Answer : A leaking transistor
Description : What leads in a simple synchro system are connected to the ac power line?
Last Answer : The rotor leads.
Description : Which of the following is a myth in testing? a) Tester can find bugs b) Any user can test software c) Missed defects are not due to testers d) Complete testing is not possible
Last Answer : Ans : b
Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.
Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration turned opposite of that in the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is ... . C. Interchange connections to 'S1' and 'S2'. D. Interchange connections to 'S1' and 'S3'.
Last Answer : Answer: D
Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move
Description : If = = in the system of equations a 1 x + b 1 y + c 1 = 0 and a 2 x + b 2 y + c 2 = 0 Statement 1 : This is the condition for inconsistent equations Statement 2 : There exists infinitely many solutions ... statements are true ? e) S1 only f) S1 and S2 g) S1 and S3 h) S2 only Answer: (d) S2 o
Last Answer : h) S2 only
Description : If = = in the system of equations a 1 x + b 1 y + c 1 = 0 and a 2 x + b 2 y + c 2 = 0 Statement 1 : This is the condition for inconsistent equations Statement 2 : There exists infinitely many ... parallel Which of the above statements are true ? a) S1 only b) S1 and S2 c) S1 and S3 d) S2 only
Last Answer : d) S2 only
Description : S1 : A man who possesses a strong will and firm determination finds all difficulties solved. S2 : _________________________________ S3 : _________________________________ S4 : _________________________________ S5 : It ... there are a thousand ways open to steer clear of all dangers and difficulties
Last Answer : (1) RPQ
Description : Given the following statements with respect to linear programming problem: S1: The dual of the dual linear programming problem is again the primal problem S2: If either the primal or the dual problem has an unbounded objective function ... S1 and S2 (B) S1 and S3 (B) S2 and S3 (D) S1, S2 and S2
Last Answer : (D) S1, S2 and S2
Description : If S1 is total number of modules defined in the program architecture, S3 is the number of modules whose correct function depends on prior processing then the number of modules not dependent on prior processing is: (A) 1 + S3/S1 (B) 1 - S3/S1 (C) 1 + S1/S3 (D) 1 - S1/S3
Last Answer : (B) 1 - S3/S1
Description : Which of the following statement(s) is/are true with respect to software architecture? S1: Coupling is a measure of how well the things grouped together in a module belong together logically. S2: Cohesion is a measure of the ... ) Only S1 and S2 (2) Only S3 (3) All of S1, S2 and S3 (4) Only S1
Last Answer : Answer: 2
Description : Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be ... be added to each final reading. D. The test reading should be subtracted from each final reading.
Description : When you zero a multispeed synchro system which synchro should you zero first?
Last Answer : The coarse synchro.
Description : Why should a synchro be rechecked for zero after it is clamped down?
Last Answer : To ensure that it did not move off zero while it was being clamped.
Description : In a control synchro system, when is the output of the CT reduced to zero?
Last Answer : When the CX and CT rotors are in correspondence.
Description : Describe the zero-position of a synchro transmitter.
Last Answer : The transmitter is in its zero-position when the rotor is aligned with the S2 stator winding.
Description : If all three ground-detection lamps continue to burn at equal intensity after the test button is depressed and released, which of the listed conditions is indicated? A. No grounds exist B. All three phases are grounded C. The test switch is faulty D. The current transformers are shorted out
Last Answer : Answer: A
Description : On a switchboard, if all three ground detection lamps remain burning at half intensity when the test button is depressed, which of the listed conditions is indicated? A. No grounds exist. B. All three phases are grounded. C. The test switch is grounded. D. The current transformers are shorted.
Description : The leads from a megohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an ____________. A. open field coil B. shorted field coil C. grounded field coil D. shunted field coil
Description : You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. ... circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.
Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter by design, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz supply ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.
Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration were in 180 degree error with those of the transmitter, what corrective action should be taken? EL-0092 A. Reverse the 60 Hz ... is proper operation. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.
Description : If coils 'R1-R2-R3' at the receiver of figure 'B' shown in the illustration turned opposite of those in the transmitter, what corrective action should be taken to have both turn in the same direction? EL-0092 A ... is needed. C. Interchange leads 'R1' and 'R3'. D. Interchange leads 'R2' and 'R3'.
Last Answer : Answer: C
Description : In order to determine whether or not 'fuse 2' shown in the illustration is defective, you should connect the voltage tester leads across points _____________. EL-0062 A. AC B. AD C. BC D. BD
Description : In order to determine whether or not 'Fuse 1', shown in the illustration is defective, you should connect the voltage tester leads across points _____________. EL-0062 A. AC B. AD C. BC D. BD
Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.
Description : which waveforms on the left have a resultant wave of zero, and what is indicated by these waves?
Last Answer : 2 and 6 have zero resultant wave and they indicate that the incident and reflected waves are 180 degrees out of phase at all parts.
Description : If an ac voltmeter is connected between the S2 and S3 windings on a TX, at what two rotor positions should the voltmeter read maximum voltage?
Last Answer : . 150º and 330º
Description : What is the reference point for alignment of all synchro units?
Last Answer : The voltmeter method.
Description : . What type of synchro system is used to transmit very large quantities?
Last Answer : A tri-speed synchro system.
Description : In a dual-speed synchro system what determines the two specific speeds at which the data will be transmitted?
Last Answer : The gear ratio between the two transmitters.
Description : What is the most probable cause of trouble in a synchro system that has all of its receivers reading incorrectly?
Last Answer : The transmitter or main bus.
Description : What type of indicator is usually placed in the stator circuit of a torque synchro system?
Last Answer : An overload indicator.
Description : Name two types of trouble you would expect to find in a newly installed synchro system.
Last Answer : Improper wiring and misalignment.
Description : What should you do with a synchro that has a bad set of bearings?
Last Answer : Replace it.
Description : What method of zeroing a synchro is perhaps the fastest but NOT necessarily the most accurate?
Last Answer : . The electrical lock method.
Description : When is a synchro receiver (TR) properly zeroed?
Last Answer : A TR is zeroed when electrical zero voltages exist across its stator windings at the same time its rotor is on zero or on its mechanical reference position.
Description : What is the purpose of the coarse setting of a synchro?
Last Answer : .It ensures the synchro is on 0º, not 180º.
Description : What is the main reason for using a multispeed synchro system instead of a single-speed synchro system?
Last Answer : Greater accuracy without the loss of self-synchronous operation.
Description : What is the name given to the synchro system that transmits data at two different speeds?
Last Answer : . A dual or double-speed synchro system.
Description : Why are synchro capacitors placed physically close to differentials transmitters and CTs?
Last Answer : To keep the connections as short as possible in order to maintain system.
Description : How are synchro capacitors connected in a circuit?
Last Answer : They are delta-connected across the stator windings.
Description : What type of current is eliminated by synchro capacitors?
Last Answer : Magnetizing current.
Description : What type of synchros usually require the use of synchro capacitors?
Last Answer : TDXs, CDXs, and Cts.
Description : What is the purpose of the synchro capacitor?
Last Answer : To improve overall synchro system accuracy by reducing stator currents.
Description : What type of synchro is used in systems requiring large amounts of power and a high degree of accuracy?
Last Answer : A control synchro.