A high Q coil has

A high Q coil has 

 (A) large band width (B) high losses (C) low losses (D) flat response
by

1 Answer

Answer :

A high Q coil has low losses

by

Related questions

In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the relation

Description : In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the relation

Last Answer : In a moving coil galvanometer, the deflection of the coil q is related to the electrical current i by the ... theta^(2)` D. `I prop sqrt(theta)`

As shown in the illustration, which listed action will occur first when push button 'Q' is depressed? EL-0017 A. Contacts 'H-1', 'H-2' and 'H-3' close. B. Contact 'H-4' closes. C. Operating coil 'C' energizes. D. Switch 'R' opens.

Description : As shown in the illustration, which listed action will occur first when push button 'Q' is depressed? EL-0017 A. Contacts 'H-1', 'H-2' and 'H-3' close. B. Contact 'H-4' closes. C. Operating coil 'C' energizes. D. Switch 'R' opens.

Last Answer : Answer: C

If the motor shown in the illustration will not start when 'Q' is depressed, which of the listed components should be checked FIRST? EL-0017 A. Fuses 'F-1' and 'F-2'. B. Operating coil 'C'. C. Contacts 'H-1', 'H-2', and 'H-3'. D. Contact 'H-4'.

Description : If the motor shown in the illustration will not start when 'Q' is depressed, which of the listed components should be checked FIRST? EL-0017 A. Fuses 'F-1' and 'F-2'. B. Operating coil 'C'. C. Contacts 'H-1', 'H-2', and 'H-3'. D. Contact 'H-4'.

Last Answer : Answer: A

The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : -

Description : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz

Last Answer : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - 10 KHz

Name the material used for :- (i) Moving coil (ii) Permanent magnet in PMMC instrument.

Description : Name the material used for :- (i) Moving coil (ii) Permanent magnet in PMMC instrument.

Last Answer : (i) Material used for Moving coil: Copper, Aluminum( some times)  (ii) Permanent magnets are made of special alloys such as :  Aluminum-Nickel-Cobalt (Alnicos)  Strontium-Iron  Neodymium-Iron-Boron  Samarium-Cobalt.

State the material used for moving coil and former for PMMC instruments.

Description : State the material used for moving coil and former for PMMC instruments. 

Last Answer : Material Used for Moving Coil and Former for PMMC Instruments:  Material used for moving coil: Copper  Material used for Former: Aluminium

A coil of 500 turns is linked with a flux of 25 mwb, when carries a current of 12.5A. Calculate the value of self-inductance.

Description : A coil of 500 turns is linked with a flux of 25 mwb, when carries a current of 12.5A. Calculate the value of self-inductance.

Last Answer : Ans: Self-Inductance: L = NΦ /I = 500 × 25 × 10-3 / 12.5 = 1 H

An oscillator that uses a tapped coil to obtain the feedback is called:

Description : An oscillator that uses a tapped coil to obtain the feedback is called: a. A Hartley circuit b. A Pierce circuit c. A multivibrator d. A negative feedback circuit

Last Answer : An oscillator that uses a tapped coil to obtain the feedback is called: a. A Hartley circuit b. A Pierce circuit c. A multivibrator d. A negative feedback circuit 

In an energymeter which coil carries the current proportional to supply voltage _____.

Description :  In an energymeter which coil carries the current proportional to supply voltage _____. 

Last Answer :  In an energymeter which coil carries the current proportional to supply voltage Pressure coil. 

The magnetic field on the axis of a current carrying polygonal coil will have only a horizontal component

Description : The magnetic field on the axis of a current carrying polygonal coil will have only a horizontal component parallel to the Plane of the coil 

Last Answer : The magnetic field on the axis of a current carrying polygonal coil will have only a horizontal component parallel to the Plane of the coil it is never possible

An iron cored inductance coil can be modelled, over a normal operating range of networks ,as

Description : An iron cored inductance coil can be modelled, over a normal operating range of networks ,as A) non-Linear bilateral element B) linear bilateral element C) linear time varying element D) non-linear time invariant element

Last Answer : An iron cored inductance coil can be modelled, over a normal operating range of networks ,as linear bilateral element

A Peterson coil is ________

Description : A Peterson coil is ________ A) An arc generating coil B) An arc suppressing coil C) An arc inducing coil D) None of these

Last Answer : A Peterson coil is An arc suppressing coil

What is the resistance of a coil which draws 10 A and dissipates 1520 W?

Description : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

Last Answer : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

lt the length, number of turns and area of a coil are doubled, the inductance of the coil

Description : lt the length, number of turns and area of a coil are  doubled, the inductance of the coil

Last Answer : lt the length, number of turns and area of a coil are  doubled, the inductance of the coil is quadrupled

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale...

Description : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

Last Answer : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is 2.5 milliOhm

The current coil of a single-phase energy meter is wound on

Description : The current coil of a single-phase energy meter is wound on (a) One limb of the laminated core (b) Both the limbs of the laminated core with same number of turns (c) Both the limbs of the laminated core with different number of turns (d) The centre of the limb on the laminated core

Last Answer : The current coil of a single-phase energy meter is wound on Both the limbs of the laminated core with same number of turns

Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil ...

Description : Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be

Last Answer : Two wattmeter method is employed to measure power in a 3 -phase balanced system with the current coil connected in the A and C lines. The phase sequence is ABC. If the wattmeter with its current coil in A -phase line reads zero, then the power factor of the 3 -phase load will be 0.5 lagging.

The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to ...

Description : The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is

Last Answer : The power consumed by a coil is 300 W when connected to a 30 V dc source and 108 W when connected to a 30 V ac source. The reactance of the coil is 4 Ohm.

The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current?

Description : The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. What is rate of change of current? A. 30 A/s B. 20 A/s C. 10 A/s D. none of these

Last Answer : The current in a 200 mH coil increases from 2 to 5 A in 0.1 Second. 30 A/s is rate of change of current.

What is the value of Inductance of a coil that induces 20 V when the current through the coil changes from...

Description : What is the value of Inductance of a coil that induces 20 V when the current through the coil changes from 12 to 20 A in 2 seconds? A. 2 H B. 3 H C. 4 H D. 5 H 

Last Answer : 5 H is the value of Inductance of a coil that induces 20 V when the current through the coil changes from 12 to 20 A in 2 seconds.

The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is:

Description : The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is: A. 16 mV B. 160 mV C. 1.6 mV D. 2.5 mV

Last Answer : The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is: 160 mV

A two-phase generator is connected to two 9012 load resistors. Each coil generates 120 V ac. The value of ...

Description : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: A. 1.33 A B. 1.88 A C. 2.66 A D. 1.77 A

Last Answer : A two-phase generator is connected to two 90Ω load resistors. Each coil generates 120 V ac. The value of current flowing through the common neutral line will be: 1.77 A

A coil of wire is placed in a changing magnetic field. If the number of turns in the coil is decreased, the...

Description : A coil of wire is placed in a changing magnetic field. If the number of turns in the coil is decreased, the voltage induced across the coil will: A. increase B. decrease C. remain constant D. be excessive

Last Answer : A coil of wire is placed in a changing magnetic field. If the number of turns in the coil is decreased, the voltage induced across the coil will: decrease

The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals....

Description : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA

Last Answer : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: 1.7 mA

The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a ...

Description : The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is A. 1,000 V B. 2,000 V C.31.25 V D. 3,125 V

Last Answer : The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is 2,000 V 

What is the pitch factor of a 4 pole alternator having 36 slots and a coil span of 1 to 8?

Description : What is the pitch factor of a 4 pole alternator having 36 slots and a coil span of 1 to 8?  (A) 140° (B) 80° (C) 20° (D) 40°

Last Answer : C

Dynamometer type moving coil instruments are provided with _____.

Last Answer : Dynamometer type moving coil instruments are provided with pneumatic damping

The series magnet of a single phase Energy meter consists of coil of _____.

Last Answer : The series magnet of a single phase Energy meter consists of coil of thick wire of few turns.

A nichrome wire used as heater coil has the resistance of 1 ohm/m. For ...

Description : A nichrome wire used as heater coil has the resistance of 1 ohm/m. For a heater of 1000 W at 200 V, the length of wire required will be 

Last Answer : A nichrome wire used as heater coil has the resistance of 1 ohm/m. For a heater of 1000 W at 200 V, the length of wire required will be 40 m.

The coil of a moving coil meter is would on

Last Answer : The coil of a moving coil meter is would on An aluminium frame.

The initial rate of rise of current through a coil of inductance 10 H when suddenly...

Description : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is_______Vs.

Last Answer : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is 20 Vs

When both the inductance and resistance of a coil are doubled the value of?

Description : When both the inductance and resistance of a coil are doubled the value of?

Last Answer : When both the inductance and resistance of a coil are doubled the value of time constant remains unchanged.

The rate of rise of current through an inductive coil is maximum?

Description : The rate of rise of current through an inductive coil is maximum?

Last Answer : The rate of rise of current through an inductive coil is maximum at the start of the current flow.

The inductance of a coil can be increased by?

Description : The inductance of a coil can be increased by?

Last Answer : The inductance of a coil can be increased by choosing core material having high relative permeability.

Inductance of coil?

Description : Inductance of coil?

Last Answer : Inductance of coil increases with the increase in supply frequency.

Inductance of a coil Varies?

Description : Inductance of a coil Varies?

Last Answer : Inductance of a coil Varies as directly as the cross-sectional area of magnetic core and inversely as the length of the iron path.

What is the difference between a coil and an inductor?

Description : What is the difference between a coil and an inductor?

Last Answer : Inductor is covering with insulating material is called coil.so they differentiate between coil and inductor.

Consider the following statements with respect to a high Q, series RLC circuit under resonance

Description : Consider the following statements with respect to a high Q, series RLC circuit under resonance 1. The voltage across R is equal to the applied voltage 2. The voltage across L and C are zero 3 ... in magnitude 4. The voltage accross L and C are maximum Which of these statements are correct?

Last Answer : Consider the following statements with respect to a high Q, series RLC circuit under resonance 1. The voltage across R is equal to the applied voltage 2. The voltage across L and C are zero 3. ... The voltage accross L and C are maximum Which of these statements are correct? 1,3 and 4

Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance ...

Description : Consider the following statements : If a high Q parallel resonant circuit is loaded with a resistance  1. The circuit impedance reduces.  2. The resonant frequency remains the same.  3. The bandwidth reduces.  Which of the above statements is/are correct ?

Last Answer : 1