The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is:

The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is: A. 16 mV B. 160 mV C. 1.6 mV D. 2.5 mV
by

1 Answer

Answer :

The voltage across a coil, when di/dt = 20 mA/s and L = 8 H, is: 160 mV

by

Related questions

A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Description : A galvanometer with 20 ohms coil resistence has a full-scale deflection of 10 mA. A 0.02 ohm is placed across the meter to increase its rating capacity. What is the new full scale current for the meter?

Last Answer : False.

For an SCR, di/dt protection is achieved through the use of

Last Answer : For an SCR, di/dt protection is achieved through the use of L in series with SCR.

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Which one of the following statements in not correct? [CDS 2003] (a) India is the highest oil-seeds and vegetable oil producing country in the world (b) India is the second largest exporter of jute goods in the world In d ian Ag r ic u l t u r ea n d An i ma l H u s ba n d r y (c) India is the largest producer of silk in world (d) India is the second largest producer of three-wheeler motor vehicles in the world

Description : Which one of the following statements in not correct? [CDS 2003] (a) India is the highest oil-seeds and vegetable oil producing country in the world (b) India is the second largest exporter of ... silk in world (d) India is the second largest producer of three-wheeler motor vehicles in the world

Last Answer : Ans: (c)

In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL-0007 A. the control fuse is the wrong amperage not allowing full current to pass through B. the stop switch is open C. an open in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Last Answer : Answer: B

A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up

Description : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is (A) 9997 Ω (B) 10000 Ω (C) 997 Ω (D) 10003 Ω

Last Answer : A moving coil meter has a resistance of 3 Ω and gives full scale deflection with 30 mA. To measure voltage up to 300 V, the external resistance to be connected in series with the instrument is 9997 Ω

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied

Description : In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

Last Answer : In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is 50 V

Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Description : Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Last Answer : Ans: 10 W*

When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is?

Description : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

Last Answer : When there is 12 mA of current through a 1.2 k ohms resistor, the voltage across the resistor is? A.14.4 V B.1.4 V C.100 V D.10 V

The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals....

Description : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: A. 1.7 mA B. 16 mA C. 12 mA D. 120 mA

Last Answer : The voltage induced across a certain coil is 200 mV. A 1200 resistor is connected to the coil terminals. The induced current will be: 1.7 mA

The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a ...

Description : The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is A. 1,000 V B. 2,000 V C.31.25 V D. 3,125 V

Last Answer : The induced voltage across a coil with 250 turns that is located in a magnetic field and is changing at a rate of 8 Wb/s is 2,000 V 

Two circular coils 1 and 2 are made from the same wire but the radius of the 1st coil is twice that of the 2nd coil. What is the ratio of potentail di

Description : Two circular coils 1 and 2 are made from the same wire but the radius of the 1st coil is twice that of the 2nd coil. What is the ratio of potentail di

Last Answer : Two circular coils 1 and 2 are made from the same wire but the radius of the 1st coil is twice that of the 2nd coil ... the same? A. 3 B. 4 C. 6 D. 2

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage

Description : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

Last Answer : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C? 7 V

In metals which of the following equation will hold good? a) Curl(H) = J b) Curl(J) = dD/dt c) Curl(H) = D d) Curl(J) = dB/dt

Description : In metals which of the following equation will hold good? a) Curl(H) = J b) Curl(J) = dD/dt c) Curl(H) = D d) Curl(J) = dB/dt

Last Answer : a) Curl(H) = J

Find the Maxwell equation derived from Faraday’s law. a) Div(H) = J b) Div(D) = I c) Curl(E) = -dB/dt d) Curl(B) = -dH/dt

Description : Find the Maxwell equation derived from Faraday’s law. a) Div(H) = J b) Div(D) = I c) Curl(E) = -dB/dt d) Curl(B) = -dH/dt

Last Answer : c) Curl(E) = -dB/dt

If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Description : If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by (A) l = dt/Sb (B) l = dt/2Sb (C) l = dt/3Sb (D) l = dt/4S

Last Answer : Answer: Option D Answer: Option D

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively?

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

In a series resonant circuit, maximum voltage across L occurs at

Description : In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

Last Answer : In a series resonant circuit, maximum voltage across L occurs at Slightly above resonant frequency

A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Description : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Last Answer : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. ... Omega` C. `1000 Omega` D. `1800 Omega`

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Last Answer : Answer: A

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the temperature difference of the governor oil heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Last Answer : Answer: C

When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause would be that the _________________. A. coil is open B. control fuse is open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Description : When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause ... open C. auxiliary contact in series with the coil is defective D. relay armature is stuck

Last Answer : Answer: A

When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown control fuse C. a reading of 'zero' on a megger from one of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Last Answer : Answer: B

One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for polarity using a/an ____________. A. iron bar across each field B. magnetic compass placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Description : One method of testing for a reversed shunt field coil in a DC generator or motor is by connecting the field to a direct current source, at reduced field rated voltage, and test for ... placed near each field C. test lamp across adjacent fields D. copper jumper across the interpole connections

Last Answer : Answer: B

What is the typical full-scale voltage across a moving coil voltmeter?

Description : What is the typical full-scale voltage across a moving coil voltmeter?

Last Answer : 50mV

A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Description : A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.

Last Answer : Answer :

The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is

Description : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is (A) 11% (B) 9% (C) 1.1% (D) 3%

Last Answer : The potential coil of a single phase dynamometer wattmeter has 4840 Ohm resistance. Voltage across the load is 220 V. With the potential coil connected on the load side, the meter indicates 100 W. Approximate percentage error due to wattmeter connection is 11%

how di i permanently disable my car alrm fuse/switch on a 1998 subaru legacy awd type L 2.2 liter engine

Description : how di i permanently disable my car alrm fuse/switch on a 1998 subaru legacy awd type L 2.2 liter engine

Last Answer : Need Answer

The expression for the inductance in terms of turns, flux and current is given by a) L = N dφ/di b) L = -N dφ/di c) L = Niφ d) L = Nφ/i

Description : The expression for the inductance in terms of turns, flux and current is given by a) L = N dφ/di b) L = -N dφ/di c) L = Niφ d) L = Nφ/i

Last Answer : a) L = N dφ/di

Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]

Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of

Description : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

Last Answer : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

The initial rate of rise of current through a coil of inductance 10 H when suddenly...

Description : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is_______Vs.

Last Answer : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is 20 Vs

The negative sign in the expression e = – N (d∅)/dt is due to:

Description : The negative sign in the expression e = – N (d∅)/dt is due to: (1) The Fleming’s Rule (2) Thumb’s Rule (3) Faraday’s Law (4) Lenz’s Law

Last Answer : The negative sign in the expression e = – N (d∅)/dt is due to:  Lenz’s Law

The equation of motion for a vibrating system with viscous damping is d 2 x/dt 2 + c/m X dx/dt + s/m X x = 0 If the roots of this equation are real, then the system will be A. over damped B. under damped C. critically damped D. none of the mentioned

Description : The equation of motion for a vibrating system with viscous damping is d 2 x/dt 2 + c/m X dx/dt + s/m X x = 0 If the roots of this equation are real, then the system will be A. over damped B. under damped C. critically damped D. none of the mentioned

Last Answer : A. over damped

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Description : If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps

Last Answer : Answer: B

If the motor fails to start and a voltmeter reading between 1 and 6, as illustrated, indicates line voltage, your next step should be to ________. EL-0007 A. replace fuse '10a' B. replace or repair contact 'Ma' C. reset and determine the cause of the overload D. check line voltage between L1 and L3

Description : If the motor fails to start and a voltmeter reading between 1 and 6, as illustrated, indicates line voltage, your next step should be to ________. EL-0007 A. replace fuse '10a' B. replace or repair contact 'Ma' C. reset and determine the cause of the overload D. check line voltage between L1 and L3

Last Answer : Answer: C

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Description : If a voltage divider is required for a load that will use 450 mA of current, what should be the value of bleeder current?

Last Answer : 45 mA rule-of-thumb.

The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The

Description : The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The resistance of the bulb is approximately? A.112 ohms B.11.2 ohms C.1.2 ohms D.18 ohms

Last Answer : 112ohm

In an energymeter which coil carries the current proportional to supply voltage _____.

Description :  In an energymeter which coil carries the current proportional to supply voltage _____. 

Last Answer :  In an energymeter which coil carries the current proportional to supply voltage Pressure coil. 

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3)) ... ` B. `90^(@)` C. `180^(@)` D. `60^(@)`

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt( ... 10 sqrt(2) A` C. `20 sqrt(2) A` D. `25 A`

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3) ... 2) A` C. `5 sqrt(6) A` D. `5 sqrt(3) A`

Output current from an LED is A. 20 mA B. 30 mA C. 40 mA D. 50 mA

Description : Output current from an LED is A. 20 mA B. 30 mA C. 40 mA D. 50 mA

Last Answer : 20 mA

Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA?

Description : Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA?

Last Answer : 4-20 mA is a standard range used to indicate measured values for any process. The reason that 4ma is chosen instead of 0 mA is for fail safe operation.  For example: A pressure instrument gives output 4mA ... is 0-20 mA then we can differentiate whether it is due to broken wire or due to 0 psi.