Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh

Reinforcement in cement concrete slab of road pavements, is placed
(A) Longitudinally
(B) Transversely
(C) Longitudinally and transversely
(D) In the form of welded wire mesh
by

1 Answer

Answer :

Answer: Option D
by

Related questions

Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Description : Expanded metal is (A) Manufactured from steel sheets (B) Used for reinforced concrete in road pavements (C) Measured in term of SWM (short way mesh) and LWM (long way mesh) (D) All the above

Last Answer : Answer: Option D

In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Description : In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Last Answer : Answer: Option D

In welded wire mesh, the longitudinal wire is placed at (A) 10 cm centres (B) 15 cm centres (C) 20 cm centres (D) 25 cm centres

Description : In welded wire mesh, the longitudinal wire is placed at (A) 10 cm centres (B) 15 cm centres (C) 20 cm centres (D) 25 cm centres

Last Answer : Answer: Option B

The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx

Last Answer : [ D ] 0.2 Lx x 0.2 Lx

For providing a raft foundation, the following activities are involved 1. Ramming the foundation bed 2. Excavation of the soil upto required depth 3. Laying the reinforcement over the foundation bed 4. Curing the cement concrete placed over reinforcement 5. Pouring the cement concrete over the reinforcement The correct sequence is (A) 1, 2, 3, 4, 5 (B) 5, 4, 3, 2, 1 (C) 2, 1, 3, 5, 4 (D) 3, 2, 5, 1,

Description : For providing a raft foundation, the following activities are involved 1. Ramming the foundation bed 2. Excavation of the soil upto required depth 3. Laying the reinforcement over the foundation bed 4. Curing the cement concrete placed over ... 2, 1 (C) 2, 1, 3, 5, 4 (D) 3, 2, 5, 1, 4

Last Answer : Answer: Option C

Rapid hardening cement is used (a) Where high early strength is desired (b) Where form work is to be removed as early as possible (c) For construction of road pavements. (d) All of the above

Description : Rapid hardening cement is used (a) Where high early strength is desired (b) Where form work is to be removed as early as possible (c) For construction of road pavements. (d) All of the above

Last Answer : (d) All of the above

For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option B

For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Description : For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Last Answer : [ A ] Ordinary Portland cement

In case of cement concrete pavements, pick up the incorrect statement (A) Tractive resistance is low (B) Initial cost of construction is high (C) Initial cost of construction is low (D) Visibility during nights is high

Description : In case of cement concrete pavements, pick up the incorrect statement (A) Tractive resistance is low (B) Initial cost of construction is high (C) Initial cost of construction is low (D) Visibility during nights is high

Last Answer : Answer: Option C

Tie bars in cement concrete pavements are at (A) Expansion joints (B) Contraction joints (C) Warping joints (D) Longitudinal joints

Description : Tie bars in cement concrete pavements are at (A) Expansion joints (B) Contraction joints (C) Warping joints (D) Longitudinal joints

Last Answer : Answer: Option D

If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Description : If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm

Last Answer : Answer: Option D

A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Description : A reinforced concrete slab is 75 mm thick. The maximum size of reinforcement bar that can be used is (a) 6 mm diameter (b) 8 mm diameter (c) 10 mm diameter (d) 12 mm diameter

Last Answer : (b) 8 mm diameter

In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Last Answer : (b) Below the neutral axis

In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Description : In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these

Last Answer : (d) All of these

If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Description : If d is the economic designed depth of a slab, the thickness of the cement concrete pavement slab at interior, is kept (A) 1.275 d (B) 1.125 d (C) 0.85 d (D) 0.75 d

Last Answer : Answer: Option C

Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Last Answer : Answer: Option B

California Bearing Ratio method of designing flexible pavements is more accurate as it involves (A) Characteristics of soils (B) Traffic intensities (C) Character of the road making materials (D) None of these

Description : California Bearing Ratio method of designing flexible pavements is more accurate as it involves (A) Characteristics of soils (B) Traffic intensities (C) Character of the road making materials (D) None of these

Last Answer : Answer: Option C

The width of road pavements, depends upon (A) Width of traffic lane (B) Number of traffic (C) Width of median strip (D) All the above

Description : The width of road pavements, depends upon (A) Width of traffic lane (B) Number of traffic (C) Width of median strip (D) All the above

Last Answer : Answer: Option D

Select the correct statement. (A) Quantity of binder required for tack coat is less than that required for prime coat (B) Prime coat treatment is given for plugging the voids in water bound macadam during bituminous road construction (C) Seal coat is the final coat over certain previous bituminous pavements (D) A bitumen primer is a high viscosity cutback

Description : Select the correct statement. (A) Quantity of binder required for tack coat is less than that required for prime coat (B) Prime coat treatment is given for plugging the voids in water ... the final coat over certain previous bituminous pavements (D) A bitumen primer is a high viscosity cutback

Last Answer : Answer: Option D

Plastic bitumen is generally used for (A) Road pavements (B) Expansion joints (C) Crack fillings (D) None to these

Description : Plastic bitumen is generally used for (A) Road pavements (B) Expansion joints (C) Crack fillings (D) None to these

Last Answer : Answer: Option C

The formula for calculating the depth of concrete pavements suggested by Gold beck, is (A) d = 3W/ max (B) d W/ max) (C) d W/ max) (D) d W/ max)

Description : The formula for calculating the depth of concrete pavements suggested by Gold beck, is (A) d = 3W/ max (B) d W/ max) (C) d W/ max) (D) d W/ max)

Last Answer : Answer: Option B

Which of the following is considered to be the highest quality construction in the group of black top pavements? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Description : Which of the following is considered to be the highest quality construction in the group of black top pavements? (A) Mastic asphalt (B) Sheet asphalt (C) Bituminous carpet (D) Bituminous concrete

Last Answer : Answer: Option D

The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Description : The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Last Answer : Answer: Option A

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force

Last Answer : Answer: Option B

Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above

Last Answer : Answer: Option D

A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above

Last Answer : Answer: Option D

In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times

Last Answer : Answer: Option A

Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab (C) In the heel slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these

Last Answer : Answer: Option D

When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Description : When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number

Last Answer : Answer: Option A

The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Last Answer : Answer: Option D

The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Description : The main reinforcement of a R.C. slab consists of 10 mm bars at 100 mm spacing; if it is desired to replace the 10 mm bars by 12 mm bars, then the spacing of 12mm bars should be (a) 120 mm (b) 140 mm (c ) 144 mm (d) 160mm

Last Answer : (c ) 144 mm

The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Description : The amount of reinforcement for main bars in a slab, is based upon (a) Maximum bending moment (b) Minimum bending moment (c) Maximum shear force (d) Minimum shear force

Last Answer : (a) Maximum bending moment

The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Description : The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above

Last Answer : (a) At the top of the slab portion over the intermediate supports.

in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Description : in a simply supported slab, the pitch of distribution reinforcement should not be more than_____________the effective depth of slab or 60cm which ever is smaller. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (c) Five times

The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Description : The pitch of bars of main reinforcement in slab should not exceed ________the effective depth of slab. (a) Double (b) Three times (c) Five times (d) Six times

Last Answer : (b) Three times

The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Description : The purpose of transverse reinforcement, in a slab is to (a) Distribute the effect to f point load on the slab more evenly and uniformly (b) Distribute the shrinkage and temp cracks more ever (c) Keep the main reinforcement in position (d) All of the above.

Last Answer : (d) All of the above.

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Last Answer : [ A ] Ks 0.25 v fck

The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only

Description : The slab is said to be orthotropically reinforced , when the reinforcement is arranged in; [ A ] Single direction [ B ] Two directions at right angles with equal meshes [ C ] Two directions at right angles with unequal meshes [ D ] At the corners only

Last Answer : [ C ] Two directions at right angles with unequal meshes

The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Last Answer : [ A ] 0.12 percent of gross cross sectional area

For the design of cement concrete pavement for corner loading, Indian Road Congress recommends the use of (A) Westergaard's formula (B) Kelly's formula (C) Goldbeck's formula (D) Picker's formula

Description : For the design of cement concrete pavement for corner loading, Indian Road Congress recommends the use of (A) Westergaard's formula (B) Kelly's formula (C) Goldbeck's formula (D) Picker's formula

Last Answer : Answer: Option D

When the bituminous surfacing is done on already existing black top road or over existing cement concrete road, the type of treatment given is (A) Seal coat (B) Tack coat (C) Prime coat (D) Spray of emulsion

Description : When the bituminous surfacing is done on already existing black top road or over existing cement concrete road, the type of treatment given is (A) Seal coat (B) Tack coat (C) Prime coat (D) Spray of emulsion

Last Answer : Answer: Option B

In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Description : In a square beam loaded longitudinally, shear develops (A) On middle fibre along horizontal plane (B) On lower fibre along horizontal plane (C) On top fibre along vertical plane (D) Equally on each fibre along horizontal plane

Last Answer : (D) Equally on each fibre along horizontal plane (D) Equally on each fibre along horizontal plane

When a rectangular beam is loaded longitudinally, shear develops on (A) Bottom fibre (B) Top fibre (C) Middle fibre (D) Every-horizontal plane

Description : When a rectangular beam is loaded longitudinally, shear develops on (A) Bottom fibre (B) Top fibre (C) Middle fibre (D) Every-horizontal plane

Last Answer : (D) Every-horizontal plane

For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16

Last Answer : Answer: Option D

If longitudinally spanning stairs are casted along with their landings, the maximum bending moment per metre width, is taken as (A) wl²/4 (B) wl²/8 (C) wl²/10 (D) wl²/12

Description : If longitudinally spanning stairs are casted along with their landings, the maximum bending moment per metre width, is taken as (A) wl²/4 (B) wl²/8 (C) wl²/10 (D) wl²/12

Last Answer : Answer: Option B

Consider the following activities in a building construction: 1. Concreting of roof slabs 2. Brick-jelly lime concrete terracing 3. Erection of form work for slab 4. Construction of parapet wall in terrace The correct sequence of these activities is (A) 1, 3, 2, 4 (B) 3, 1, 4, 2 (C) 3, 1, 2, 4 (D) 1, 3, 4, 2

Description : Consider the following activities in a building construction: 1. Concreting of roof slabs 2. Brick-jelly lime concrete terracing 3. Erection of form work for slab 4. Construction of parapet wall in terrace The correct sequence of these ... (B) 3, 1, 4, 2 (C) 3, 1, 2, 4 (D) 1, 3, 4, 2

Last Answer : (C) 3, 1, 2, 4

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept (A) 0.7 (B) 0.8 (C) 0.9 (D) 0.6

Last Answer : Answer: Option C

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Description : The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate span is kept. (a) 0.7 (b) 0.8 (c) 0.9 (d) 0.6

Last Answer : (c) 0.9