Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above
Last Answer : [ B ] 0.87 fy
Description : The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel
Last Answer : Answer: Option D
Description : The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%
Last Answer : [ A ] 0.12%
Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.
Last Answer : [ A ] 0.12 percent of gross cross sectional area
Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045
Last Answer : (c) 0.0037
Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending
Last Answer : [ C ] The strain at different points in the section will be same
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2
Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5
Last Answer : (c) 4, 1, 3, 5 and 2
Description : For Fe- 415 steel and M20grade concrete, the balanced percentage of steel is [ A ] 0.65% [ B ] 0.75% [ C ] 0.86% [ D ] 0.96%
Last Answer : [ D ] 0.96%
Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5
Last Answer : (C) 1/4
Description : The theoretical stress-strain curve of the concrete in the Limit State design of structures is correspondingly reduced by the factor [ A ] 0.35 [ B ] 0.5 [ C ] 0.67 [ D ] 0.75
Last Answer : [ C ] 0.67
Description : The compression in concrete (fc) at failure is given by [ A ] 0.30 fck [ B ] 0.45 fck [ C ] 0.50 fck [ D ] 0.75 fck
Last Answer : [ B ] 0.45 fck
Description : The stress-strain curve concrete in compression follows [ A ] a straight line [ B ] a rectangular parabolic curve [ C ] a semi circular arc [ D ] a cubic parabola
Last Answer : [ B ] a rectangular parabolic curve
Description : A simply supported wooden beam 150 cm long and having a cross section 16 cm × 24 cm carries a concentrated load, at the centre. If the permissible stress ft = 75 kg/cm2 and fs= 10 kg/cm2 the safe load is (A) 3025 kg (B) 3050 kg (C) 3075 kg (D) 3100 kg
Last Answer : (C) 3075 kg
Description : Stress strain curve of high tensile steel (A) Has a definite yield point (B) Does not show definite yield point but yield point is defined by 0.1% proof stress (C) Does not show definite yield ... proof stress (D) Does not show definite yield point but yield point is defined by 2% proof stress,
Last Answer : Answer: Option C
Description : According to IS: 456-2000 the ultimate moment of resistance of a slab for Fe - 415 HYSD bars is; [ A ] Mu = 0.138 fck bd2 [ B ] Mu = 0.145 fck bd2 [ C ] Mu = 0.152 fck bd2 [ D ] Mu = 0.165 fck bd2
Last Answer : [ A ] Mu = 0.138 fck bd2
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Last Answer : Answer: Option B
Description : The ultimate failure is assumed to be reached when the section reaches a uniform compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.005
Last Answer : [ A ] 0.002
Description : The concrete is assumed to reach failure with a compression strain of [ A ] 0.002 [ B ] 0.0035 [ C ] 0.0045 [ D ] 0.006
Last Answer : [ B ] 0.0035
Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material
Last Answer : c. Energy required to cause failure
Description : Minimum percentage area of tension reinforcement , when the grade of steel is Fe-250 [ A ] 0.2 [ B ] 0.25 [ C ] 0.34 [ D ] 0.44
Last Answer : [ C ] 0.34
Description : Increase-strain curve of concrete is (a) A perfect straight line upto failure (b) Straight line up to 0.002% strain value and then parabolic upto failure (c) Nearly parabolic up to 0.002% strain ... line upto failure (d) Hyperbolic up to 0.002% strain value and then a straight line upto failure
Last Answer : (c) Nearly parabolic up to 0.002% strain value and the a straight line upto failure
Description : According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038
Last Answer : [ D ] 0.0038
Description : According to IS:456-2000, Limiting value of yield strain for Fe250 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038
Last Answer : [ B ] 0.0031
Description : What Are The Points In The Stress Strain Curve For Steel?
Last Answer : Proportional limit, elastic limit or yield point, ultimate stress and stress at failure.
Description : Pick up the correct statement from the following: (A) The height of head light above road surface, is taken as 0.75 m (B) The beam of head light is up to one degree upwards from the grade of road (C) While designing the valley curve, the height of the object is assumed nil (D) All the above
Description : According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75
Last Answer : [ B ] 0.55
Description : Assume postal rates for 'light letters' are: $0.25 up to 10 grams; $0.35 up to 50 grams; $0.45 up to 75 grams; $0.55 up to 100 grams. Which test inputs (in grams) would be selected using boundary value analysis? A. 0, 9,19, ... C. 0, 1,10,11, 50, 51, 75, 76,100,101 D. 25, 26, 35, 36, 45, 46, 55, 56
Last Answer : C. 0, 1,10,11, 50, 51, 75, 76,100,101
Description : How many F's can you have to not pass 6th grade?
Last Answer : I think it depends on the school. With one F you are probably ok, but once you have several F's it's possible you may have to go to summer school to take the classes over. If you are concerned about not passing I would speak to your teacher about doing some extra credit.
Description : Which of the following theories of failure is most appropriate for a brittle material? (a) Maximum principal strain theory (b) Maximum principal stress theory (c) Maximum shear stress theory (d) Maximum strain energy theory
Last Answer : (b) Maximum principal stress theory
Description : For M 150 grade concrete (1:2:4) the moment of resistance factor is (A) 0.87 (B) 8.50 (C) 7.50 (D) 5.80
Description : 16. The shear stress-strain graph for a Non-Newtonian fluid is a curve. A) Correct B) Incorrect
Last Answer : A
Description : The shear stress-strain graph for a Newtonian fluid is a (A) Straight line (B) Parabolic curve (C) Hyperbolic curve (D) Elliptical
Last Answer : Answer: Option A
Description : Consider the following statements: 1. For a saturated soil, Skempton's B-parameter is nearly equal to unity. 2. For an undisturbed sensitive clay, the stress-strain curve shows a peak. 3. Interlocking contributes significantly to the shearing ... 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only
Last Answer : (a) 1, 2 & 3
Description : Percentage content of silica in window glass, is (A) 40 to 45 (B) 50 to 55 (C) 60 to 65 (D) 70 to 75
Description : The proof stress in steel is the stress corresponding to the strain of [ A ] 0.2 [ B ] 0.02 [ C ] 0.002 [ D ] 0.0002
Last Answer : [ C ] 0.002
Description : An exceptional grade may be provided upto 1 in 12 along hill roads, if the length does not exceed (A) 45 m per km (B) 60 m per km (C) 75 m per km (D) 90 m per km
Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure
Last Answer : Option A
Description : Select the incorrect statement. (A) In a direct shear box test, the plane of shear failure is predetermined (B) Better control is achieved on the drainage of the soil in a triaxial compression ... compression test is uniform (D) Unconfined compression test can be carried out on all types of soils
Description : In a batch, 40% of the students offered Maths, 30% offered science and 15% offered both. If a student is selected at random, what is the probability that they has offered science or maths? A) 0.55 B) 0.65 C) 0.45 D) 0.75
Last Answer : Answer: A) P(M) = 0.40 P(S) =0.30 and P(M∩S) = 0.15 P(M∪S) = P(M) + P(S) - P(M∩S) = 0.55
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm
Description : If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young's modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is: (A) (1 - C)mf - eE B) (C - 1)mf + eE (C) (C - 1)mf - eE (D) (1 - C)mf + eE
Description : Fractional increase in original length is called A. stress B. strain C. tensile force D. compression
Last Answer : strain
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm