Minimum percentage area of tension reinforcement , when the grade of steel is Fe-250 [ A ] 0.2 [ B ] 0.25 [ C ] 0.34 [ D ] 0.44

Minimum percentage area of tension reinforcement , when the grade of steel is Fe-250
[ A ] 0.2
[ B ] 0.25
[ C ] 0.34
[ D ] 0.44
by

1 Answer

Answer :

[ C ] 0.34
by

Related questions

The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Description : The Minimum amount of steel for Main reinforcement in slab should be (Fe 415- grade of steel) [ A ] 0.12 percent of gross cross sectional area [ B ] 0.15 percent of gross cross sectional area [ C ] 0.20 percent of gross cross sectional area [ D ] 0.25 percent of gross cross sectional area.

Last Answer : [ A ] 0.12 percent of gross cross sectional area

The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Description : The Minimum percentage of secondary steel in slabs for Fe- 415 grade steel should be __________ of Gross cross-section area [ A ] 0.12% [ B ] 0.15% [ C ] 0.20% [ D ] 0.25%

Last Answer : [ A ] 0.12%

Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Description : Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Last Answer : [ A ] 0.2

Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Description : Minimum percentage of tension steel for a singly reinforced section Fe415 grade is [ A ] 0.2 [ B ] 0.35 [ C ] 2 [ D ] 3.5

Last Answer : [ A ] 0.2

Design shear strength of concrete is a function of i.Percentage of tension steel ii.Grade of concrete iii.Grade of steel [ A ] i and ii [ B ] ii only [ C ] i and iii [ D ] i, ii and iii

Description : Design shear strength of concrete is a function of i.Percentage of tension steel ii.Grade of concrete iii.Grade of steel [ A ] i and ii [ B ] ii only [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i and ii

The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Description : The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %

Last Answer : Answer: Option C

The compression in steel (fS) at failure for Fe - 415 grade steel using stress-strain curve shall be [ A ] 0.87 fy [ B ] 0.75 fy [ C ] 0.45 fy [ D ] 0.55 fy

Description : The compression in steel (fS) at failure for Fe - 415 grade steel using stress-strain curve shall be [ A ] 0.87 fy [ B ] 0.75 fy [ C ] 0.45 fy [ D ] 0.55 fy

Last Answer : [ B ] 0.75 fy

The minimum percentage of tension steel is mainly based on the [ A ] Total depth [ B ] Effective depth [ C ] Both (a) and (b) [ D ] None of the above.

Description : The minimum percentage of tension steel is mainly based on the [ A ] Total depth [ B ] Effective depth [ C ] Both (a) and (b) [ D ] None of the above.

Last Answer : [ A ] Total depth

The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %

Description : The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %

Last Answer : Answer: Option C

Maximum area of tension reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Description : Maximum area of tension reinforcement shall not exceed [ A ] 0.02 bd [ B ] 0.02 bD [ C ] 0.04 bd [ D ] 0.04 bD

Last Answer : [ D ] 0.04 bD

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

For Fe- 415 steel and M20grade concrete, the balanced percentage of steel is [ A ] 0.65% [ B ] 0.75% [ C ] 0.86% [ D ] 0.96%

Description : For Fe- 415 steel and M20grade concrete, the balanced percentage of steel is [ A ] 0.65% [ B ] 0.75% [ C ] 0.86% [ D ] 0.96%

Last Answer : [ D ] 0.96%

In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Description : In R.C. sewer pipes, the percentage longitudinal reinforcement to the cross-sectional area of concrete is kept A. 10.0 B. 5.0 C. 2.0 D. 0.25

Last Answer : ANS: D

The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Description : The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Last Answer : [ A ] 25 mm

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

Minimum reinforcement in slabs, when High yield strength deformed bars [ A ] 0.12% of gross cross sectional area [ B ] 0.15% of gross cross sectional area [ C ] 0.20% of gross cross sectional area [ D ] 0.25% of gross cross sectional area.

Description : Minimum reinforcement in slabs, when High yield strength deformed bars [ A ] 0.12% of gross cross sectional area [ B ] 0.15% of gross cross sectional area [ C ] 0.20% of gross cross sectional area [ D ] 0.25% of gross cross sectional area.

Last Answer : [ A ] 0.12% of gross cross sectional area

The Maximum percentage of steel in tension allowed for beams [ A ] 0.2 [ B ] 0.4 [ C ] 2 [ D ] 4

Description : The Maximum percentage of steel in tension allowed for beams [ A ] 0.2 [ B ] 0.4 [ C ] 2 [ D ] 4

Last Answer : [ A ] 0.2

A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2  MN/mm2  and Poisson's ratio is 0.25, the change in the volume of the bar is:  (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Last Answer : (C) 3.125 cm

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Description : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50'. What number is missing? -Riddles

Last Answer : 22

Total number of State Agriculture University in India in the year 2004 was (A) 25 (B) 44 (C) 34 (D) 30

Description : Total number of State Agriculture University in India in the year 2004 was (A) 25 (B) 44 (C) 34 (D) 30

Last Answer : (C) 34

According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Last Answer : [ D ] 750 mm

The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension

Last Answer : Answer: Option D

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Description : Shear resistance of concrete in a reinforced concrete beam is dependent on (a) Tension reinforcement in the beam (b) Compression reinforcement in the beam (c ) Shear reinforcement in the beam (d) None of the reinforcements in the beam

Last Answer : (a) Tension reinforcement in the beam

Minimum steel required in slabs is mainly controlled by the following consideration [ A ] Cracking on the tension side [ B ] Shrinkage and creep [ C ] Both (a) and (b) [ D ] None of the above.

Description : Minimum steel required in slabs is mainly controlled by the following consideration [ A ] Cracking on the tension side [ B ] Shrinkage and creep [ C ] Both (a) and (b) [ D ] None of the above.

Last Answer : [ B ] Shrinkage and creep

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than (A) 0.15 (B) 0.12 (C) 0.30 (D) 1.00

Description : The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than (A) 0.15 (B) 0.12 (C) 0.30 (D) 1.00

Last Answer : Answer: Option B

The limits of percentage p of the longitudinal reinforcement in a column is given by (A) 0.15% to 2% (B) 0.8% to 4% (C) 0.8% to 6% (D) 0.8% to 8%

Description : The limits of percentage p of the longitudinal reinforcement in a column is given by (A) 0.15% to 2% (B) 0.8% to 4% (C) 0.8% to 6% (D) 0.8% to 8%

Last Answer : Answer: Option C

The percentage of reinforcement in slabs is generally in the range of [ A ] 0.3% to 0.5% [ B ] 0.5% to 1.0% [ C ] 1.0% to 1.5% [ D ] 1.5 % to 2.0%

Description : The percentage of reinforcement in slabs is generally in the range of [ A ] 0.3% to 0.5% [ B ] 0.5% to 1.0% [ C ] 1.0% to 1.5% [ D ] 1.5 % to 2.0%

Last Answer : [ A ] 0.3% to 0.5%

As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2

Description : As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2

Last Answer : [ B ] 0.8 N/mm2

Minimum grade of concrete to be used in reinforced concrete as per IS: 4561978 is (A) M 15 (B) M 20 (C) M 10 (D) M 25

Description : Minimum grade of concrete to be used in reinforced concrete as per IS: 4561978 is (A) M 15 (B) M 20 (C) M 10 (D) M 25

Last Answer : Answer: Option A

The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Last Answer : (c) 0.0037

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

Minimum percentage of longitudinal steel in a column should not be less than [ A ] 0.60% [ B ] 0.80% [ C ] 1.00% [ D ] 1.20%

Description : Minimum percentage of longitudinal steel in a column should not be less than [ A ] 0.60% [ B ] 0.80% [ C ] 1.00% [ D ] 1.20%

Last Answer : [ B ] 0.80%

Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is (A) 28 liters (B) 30 liters (C) 32 liters (D) 34 liters

Description : Maximum quantity of water needed per 50 kg of cement for M 15 grade of concrete is (A) 28 liters (B) 30 liters (C) 32 liters (D) 34 liters

Last Answer : Answer: Option C

In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Description : In a limit state method of design, when shear reinforcement is not provided, the calculated shear stress at the critical section of a slab shall not exceed; [ A ] Ks 0.25 v fck [ B ] ks 0.20 v fck [ C ] ks 0.16 v fck [ D ] ks 0.10 v fck

Last Answer : [ A ] Ks 0.25 v fck

The distance travelled per turn of α-helix in nm is (A) 0.34 (B) 0.44 (C) 0.54 (D) 0.64

Description : The distance travelled per turn of α-helix in nm is (A) 0.34 (B) 0.44 (C) 0.54 (D) 0.64

Last Answer : Answer : C

f the mass is of 10 Kg, find the natural frequency in Hz of the free longitudinal vibrations. The displacement is 0.01mm. a) 44.14 b) 49.85 c) 43.43 d) 46.34

Description : f the mass is of 10 Kg, find the natural frequency in Hz of the free longitudinal vibrations. The displacement is 0.01mm. a) 44.14 b) 49.85 c) 43.43 d) 46.34

Last Answer : b) 49.85

Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Description : Percentage of carbon content in mild steel is (A) Less than 0.25 (B) Between 0.25 and 0.7 (C) Between 0.7 and 1.5 (D) Greater than 1.5

Last Answer : Answer: Option A

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : (C) 200 kg/cm2

Ordinary concrete is not used for concrete grade (A) M 100 (B) M 150 (C) M 250 (D) M 40

Description : Ordinary concrete is not used for concrete grade (A) M 100 (B) M 150 (C) M 250 (D) M 40

Last Answer : (D) M 400

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

If the various concrete ingredients i.e. cement, sand and aggregates are in the ratio of 1:3:6, the grade of concrete, is (A) M 100 (B) M 150 (C) M 200 (D) M 250

Description : If the various concrete ingredients i.e. cement, sand and aggregates are in the ratio of 1:3:6, the grade of concrete, is (A) M 100 (B) M 150 (C) M 200 (D) M 250

Last Answer : Answer: Option A

In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2

Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2

Last Answer : (A) 100 kg/cm2

Maximum percentage reinforcement in case of slabs is limited to (A) 2 (B) 4 (C) 6 (D) 8

Description : Maximum percentage reinforcement in case of slabs is limited to (A) 2 (B) 4 (C) 6 (D) 8

Last Answer : (B) 4

A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The rolling resistance of the road will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Description : A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The ... will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Last Answer : (C) 40 kg/tonne