According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above

According to IS:456-2000, the minimum eccentricity in no case
[ A ] Shall be not less than 20mm
[ B ] Shall be not greater than 30mm
[ C ] Shall be 20mm-30mm
[ D ] None of the above
by

1 Answer

Answer :

[ A ] Shall be not less than 20mm
by

Related questions

According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Description : According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18

Last Answer : [ A ] Less than 12

According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm

Last Answer : [ B ] 300 mm

In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Description : According to IS: 456 -2000, the spacing of links in a Column should be less than [ A ] 16 x diameter of smallest longitudinal bar [ B ] 24 x diameter of smallest longitudinal bar [ C ] 48 x diameter of smallest longitudinal bar [ D ] 48 x diameter of greatest longitudinal bar

Last Answer : [ A ] 16 x diameter of smallest longitudinal bar

The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

According to IS 456, minimum slenderness ratio for a short concrete column is (a) Less than 12 (b) Between 12 and 18 (c) Between 18 and 24 (d) More than 24

Description : According to IS 456, minimum slenderness ratio for a short concrete column is (a) Less than 12 (b) Between 12 and 18 (c) Between 18 and 24 (d) More than 24

Last Answer : (a) Less than 12

Which of the following method that is used to taken into account the slenderness effect of columns according to IS:456 - 2000 [ A ] Reduction coefficient method [ B ] Slenderness method [ C ] Moment magnification method [ D ] None of the above

Description : Which of the following method that is used to taken into account the slenderness effect of columns according to IS:456 - 2000 [ A ] Reduction coefficient method [ B ] Slenderness method [ C ] Moment magnification method [ D ] None of the above

Last Answer : [ A ] Reduction coefficient method

Permissible width of crack at the surface of concrete for „moderate‟ environmental conditions according to IS : 456-2000 is [ A ] 0.1 mm [ B ] 0.2 mm [ C ] 0.3 mm [ D ] 0.4 mm

Description : Permissible width of crack at the surface of concrete for „moderate‟ environmental conditions according to IS : 456-2000 is [ A ] 0.1 mm [ B ] 0.2 mm [ C ] 0.3 mm [ D ] 0.4 mm

Last Answer : [ B ] 0.2 mm

According to IS: 456-2000 the ultimate moment of resistance of a slab for Fe - 415 HYSD bars is; [ A ] Mu = 0.138 fck bd2 [ B ] Mu = 0.145 fck bd2 [ C ] Mu = 0.152 fck bd2 [ D ] Mu = 0.165 fck bd2

Description : According to IS: 456-2000 the ultimate moment of resistance of a slab for Fe - 415 HYSD bars is; [ A ] Mu = 0.138 fck bd2 [ B ] Mu = 0.145 fck bd2 [ C ] Mu = 0.152 fck bd2 [ D ] Mu = 0.165 fck bd2

Last Answer : [ A ] Mu = 0.138 fck bd2

According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Description : According to IS: 456-2000, the span/overall depth ratio for a continuous two-way slab in order to control deflection is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ C ] 32

The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by

Description : The span/over all depth ratio for a simply supported two-way slab according to IS : 456- 2000 is given by [ A ] 20 [ B ] 28 [ C ] 32 [ D ] 40

Last Answer : [ B ] 28

According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.

Description : According to IS : 456-2000, clause 39.4, stirrups should be provided for a shear of [ A ] at least 75% [ B ] at least 50% [ C ] at least 25 % [ D ] none of the above.

Last Answer : [ B ] at least 50%

According to IS:456-2000, Limiting value of yield strain for Fe250grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS:456-2000, Limiting value of yield strain for Fe250grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ B ] 0.0031

According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ D ] 0.0038

According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3

Description : According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3

Last Answer : [ B ] 0.4 kg/m3

According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Description : According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Last Answer : [ C ] 450 kg/m3

According to IS:456-2000, the following type of environments are considered for durability of concrete [ A ] two [ B ] four [ C ] five [ D ] six

Description : According to IS:456-2000, the following type of environments are considered for durability of concrete [ A ] two [ B ] four [ C ] five [ D ] six

Last Answer : [ C ] five

According to IS:456-2000, the maximum allowable crack width (in mm) for mild type of environmental condition [ A ] 0.1 [ B ] 0.2 [ C ] 0.25 [ D ] 0.3

Description : According to IS:456-2000, the maximum allowable crack width (in mm) for mild type of environmental condition [ A ] 0.1 [ B ] 0.2 [ C ] 0.25 [ D ] 0.3

Last Answer : [ D ] 0.3

According to IS:456-2000, Limiting value of yield strain for Fe250 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS:456-2000, Limiting value of yield strain for Fe250 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ B ] 0.0031

According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Description : According to IS: 456-2000, limiting value of yield strain for Fe415 grade steel is [ A ] 0.031 [ B ] 0.0031 [ C ] 0.038 [ D ] 0.0038

Last Answer : [ D ] 0.0038

According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3

Description : According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3

Last Answer : [ B ] 0.4 kg/m3

According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Description : According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Last Answer : [ C ] 450 kg/m3

According to IS:456-2000, the following type of environments are considered for durability of concrete [ A ] two [ B ] four [ C ] five [ D ] six

Description : According to IS:456-2000, the following type of environments are considered for durability of concrete [ A ] two [ B ] four [ C ] five [ D ] six

Last Answer : [ C ] five

According to IS:456-2000, the maximum allowable crack width (in mm) for mild type of environmental condition [ A ] 0.1 [ B ] 0.2 [ C ] 0.25 [ D ] 0.3

Description : According to IS:456-2000, the maximum allowable crack width (in mm) for mild type of environmental condition [ A ] 0.1 [ B ] 0.2 [ C ] 0.25 [ D ] 0.3

Last Answer : [ D ] 0.3

According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm

Last Answer : [ C ] lesser of 0.75 d or 300 mm

As per 1S: 456-2000, minimum grade of concrete in seat water constructions is [ A ] M20 [ B ] M25 [ C ] M30 [ D ] M50

Description : As per 1S: 456-2000, minimum grade of concrete in seat water constructions is [ A ] M20 [ B ] M25 [ C ] M30 [ D ] M50

Last Answer : [ C ] M30

As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Description : As per IS: 456-2000, the maximum size of aggregate is [ A ] 1/4 of maximum thickness of member [ B ] 1/4 of minimum thickness of member [ C ] 1/5 of maximum thickness of member [ D ] 1/5 of minimum thickness of member

Last Answer : [ B ] 1/4 of minimum thickness of member

Minimum grade of concrete for R.C.C. should be _________ , as per IS. 456-2000 [ A ] M10 [ B ] M14 [ C ] M20 [ D ] M25

Description : Minimum grade of concrete for R.C.C. should be _________ , as per IS. 456-2000 [ A ] M10 [ B ] M14 [ C ] M20 [ D ] M25

Last Answer : [ C ] M20

According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Description : According to IS:456-1978, the spacing of stirrups shall not exceed a distance ______the leverarm of the resisting moment. (a) Equal to (b) Two times (c) Three times (d) All the above

Last Answer : (a) Equal to

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

As per I.S. 456 - 1978, the pH value of water shall be (A) Less than 6 (B) Equal to 6 (C) Not less than 6 (D) Equal to 7

Description : As per I.S. 456 - 1978, the pH value of water shall be (A) Less than 6 (B) Equal to 6 (C) Not less than 6 (D) Equal to 7

Last Answer : Answer: Option C

According to the recommendations of IS : 456-1978, the expansion joints (A) Are provided where plane changes abruptly (B) Are provided to ensure minimum resistance (C) Do not carry reinforcement across them (D) All the above

Description : According to the recommendations of IS : 456-1978, the expansion joints (A) Are provided where plane changes abruptly (B) Are provided to ensure minimum resistance (C) Do not carry reinforcement across them (D) All the above

Last Answer : Answer: Option D

According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Description : According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Last Answer : [ B ] 300 kg/m3

According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Description : According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3

Last Answer : [ B ] 300 kg/m3

Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Last Answer : (d) All the above

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Last Answer : Answer: Option B

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option C

As per IS:456, the strength of concrete sample is less than [ A ] The characteristic strength minus 1.35times the standard deviation [ B ] 0.80 times the characteristic strength [ C ] Greater of (a) and (b) [ D ] None of the above

Description : As per IS:456, the strength of concrete sample is less than [ A ] The characteristic strength minus 1.35times the standard deviation [ B ] 0.80 times the characteristic strength [ C ] Greater of (a) and (b) [ D ] None of the above

Last Answer : [ C ] Greater of (a) and (b)

Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Last Answer : [ B ] 30 mm

Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Description : Nominal cover for M30 grade concrete in moderate exposure is (as per IS:456-2000) [ A ] 20 mm [ B ] 30 mm [ C ] 45 mm [ D ] 50 mm

Last Answer : [ B ] 30 mm

As per IS: 456-2000, recommended value for standard deviation for concrete mix from M30 to M50 is [ A ] 1 N/mm2 [ B ] 2 N/mm2 [ C ] 4 N/mm2 [ D ] 5 N/mm2

Description : As per IS: 456-2000, recommended value for standard deviation for concrete mix from M30 to M50 is [ A ] 1 N/mm2 [ B ] 2 N/mm2 [ C ] 4 N/mm2 [ D ] 5 N/mm2

Last Answer : [ D ] 5 N/mm2

As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK

Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK

Last Answer : [ B ] 5000 vfCK

The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm

Description : The length of the vicat plunger is (a) 40mm (b) 60mm (c) 50mm (d) 30mm

Last Answer : (c) 50mm

If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d

Last Answer : Answer: Option D

According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option A

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

According to I.S. : 456, the number of grades of concrete mixes, is (A) 3 (B) 4 (C) 5 (D) 7

Description : According to I.S. : 456, the number of grades of concrete mixes, is (A) 3 (B) 4 (C) 5 (D) 7

Last Answer : (D) 7

According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75

Description : According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75

Last Answer : [ B ] 0.55

According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75

Description : According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75

Last Answer : [ B ] 0.55