Description : According to IS:456 minimum cement content inclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3
Last Answer : [ B ] 300 kg/m3
Description : According to IS: 456-2000, the maximum cement content exclusive of admixtures is [ A ] 200 kg/m3 [ B ] 300 kg/m3 [ C ] 450 kg/m3 [ D ] 550 kg/m3
Last Answer : [ C ] 450 kg/m3
Description : According to IS: 456-2000 Maximum spacing of shear reinforcement in no case shall not exceed [ A ] 250 mm [ B ] 300 mm [ C ] 350 mm [ D ] 450 mm
Last Answer : [ B ] 300 mm
Description : According to IS: 456-2000 spacing of vertical stirrups for shear reinforcement has been limited to [ A ] 0.75 d [ B ] 450 mm [ C ] lesser of 0.75 d or 300 mm [ D ] lesser of 0.75d or 450 mm
Last Answer : [ C ] lesser of 0.75 d or 300 mm
Description : According to IS:456-2000, the total acid soluble chlorides in concrete is restricted to________ of concrete [ A ] 0.2 kg/m3 [ B ] 0.4 kg/m3 [ C ] 2 kg/m3 [ D ] 4 kg/m3
Last Answer : [ B ] 0.4 kg/m3
Description : Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm
Last Answer : Answer: Option B
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550
Last Answer : A. 575
Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550
Last Answer : a) 575
Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300
Last Answer : (C) 350-400
Description : The grade of concrete not recommended by I.S. : 456, is (A) M 100 (B) M 200 (C) M 300 (D) M 500
Last Answer : (D) M 500
Description : According to IS: 456, maximum water-cement ratio should be [ A ] 0.45 [ B ] 0.55 [ C ] 0.65 [ D ] 0.75
Last Answer : [ B ] 0.55
Description : For 12 mm thick cement plastering 1 : 6 on 100 sq.m new brick work, the quantity of cement required, is (A) 0.200 m3 (B) 0.247 m3 (C) 0.274 m3 (D) 0.295 m
Last Answer : (C) 0.274 m3
Description : If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is (A) 28 d (B) 38 d (C) 48 d (D) 58 d
Last Answer : Answer: Option D
Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm
Last Answer : Answer: Option A
Description : The value of 'C' of Indian type W.C. shown in the given figure is: (A) 400 mm (B) 450 mm (C) 500 mm (D) 550 mm
Last Answer : (C) 500 mm
Description : Number of bricks required for one cubic metre of brick masonry is (A) 400 (B) 450 (C) 500 (D) 550
Last Answer : Answer: Option C
Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm
Last Answer : [ D ] 750 mm
Description : The live load to be considered for an accessible roof, is (A) Nil (B) 75 kg/m3 (C) 150 kg/m2 (D) 200 kg/cm
Description : The mass of 2.5 m3 of a certain liquid is 2 tonnes. Its mass density is (A) 200 kg/m3 (B) 400 kg/m3 (C) 600 kg/m3 (D) 800 kg/m
Description : During first six months of lactation, the following increment in energy intake is recommended: (A) 200 kcal/day (B) 300 kcal/day (C) 550 kcal/day (D) 1,000 kcal/day
Last Answer : Answer : C
Description : Temperature and pressure in urea autoclave is (A) 120°C and 300 atm (B) 190°C and 200 atm (C) 400°C and 550 atm (D) 200°C and 10 atm
Last Answer : (B) 190°C and 200 atm
Description : According to the recommendations of IS : 456-1978, the expansion joints (A) Are provided where plane changes abruptly (B) Are provided to ensure minimum resistance (C) Do not carry reinforcement across them (D) All the above
Description : According to IS 456, minimum slenderness ratio for a short concrete column is (a) Less than 12 (b) Between 12 and 18 (c) Between 18 and 24 (d) More than 24
Last Answer : (a) Less than 12
Description : According to IS:456-2000, the minimum slenderness ratio for a short column is [ A ] Less than 12 [ B ] Between 12 and 18 [ C ] Less than 18 [ D ] Must be greater than 18
Last Answer : [ A ] Less than 12
Description : In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm
Last Answer : [ B ] 6 mm
Description : According to IS:456-2000, the minimum eccentricity in no case [ A ] Shall be not less than 20mm [ B ] Shall be not greater than 30mm [ C ] Shall be 20mm-30mm [ D ] None of the above
Last Answer : [ A ] Shall be not less than 20mm
Description : Utilizing the answer to the previous problem, estimate the overall or average increase in temperature ( ΔT) of the concrete roof from the energy absorbed from the sun during a12hour day. Assume that all of the radiation absorbed goes into ... °C b. 8.9°C c. 9.9°C d. 10.9°C formula: ΔQ = m c ΔT
Last Answer : 7.9 °C
Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%
Last Answer : D. 83%
Description : Match List-I (crops) with List-II (water requirement) and select your answer from the code given below- List-I (a) Jowar (b) Soybean (c) Cotton (d) Groundnut List-II 1. 140 mm - 300 mm 2. 350 mm - 450 mm 3. 200 mm - 300 mm 4. 300 mm - ... (b) (c) (d) (A) 3 1 2 4 (B) 4 2 3 1 (C) 1 4 2 3 (D) 3 1 4 2
Last Answer : (C) 1 4 2 3
Description : Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm
Last Answer : (b) 400-600 mm
Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200
Last Answer : (A) 700 - 1000
Description : What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600
Last Answer : (B) 200-300
Description : What is the range of the visible light cure beam: A. 100-120 nm B. 200-300 nm C. 400-430 nm D. 470 nm or 450-500 nm
Last Answer : D. 470 nm or 450-500 nm
Description : The ratio of the monthly salaries of A and B is in the ratio 15 : 16 and that of B and C is in the ratio 17 : 18. Find the monthly income of C if the total of their monthly salary is Rs 1,87,450. A) Rs 66,240 B) Rs 72,100 C) Rs 62,200 D) Rs 65,800 E) Rs 60,300
Last Answer : Answer: A A/B = 15/16 and B/C = 17*18 So A : B : C = 15*17 : 16*17 : 16*18 = 255 : 272 : 288 So C’s salary = [288/(255+272+288)] * 1,87,450= Rs 66,240
Description : What is the electric field intensity at a distance of 20cm from a charge 2 X 10 -6 C in vacuum? a) 250,000 b) 350,000 c) 450,000 d) 550,000
Last Answer : c) 450,000
Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850
Last Answer : (B) 350 to 450
Description : In tractor transmission oil and oil from the steering worm and sector housing should be changed after how many working hours? 1.450 2. 550 3. 650 4. 750
Last Answer : ans 4
Description : The labelled price of a product is Rs 750. If it is sold at a 20% discount, the dealer earns a 25% profit. What is the cost price? 1. Rs 550 2. Rs 450 3. Rs 435 4. Rs 480
Last Answer : 1. Rs 550
Description : Number of bricks required for 1 cubic meter of brick masonry is a)400 b) 450 c) 500* d) 550
Last Answer : c) 500*
Description : Pick up the wrong nominal internal diameter of cast iron (spun) pipes in mm from the following: (A) 300 (B) 400 (C) 550 (D) 650
Last Answer : (C) 550
Description : Calorific value of pitch creosote mixture (PCM) i.e., C.T.F.-200 is about (A) 8800 kcal/m3 (B) 8800 kcal/kg (C) Same as that of coal middling (D) 25000 kcal/kg
Last Answer : (B) 8800 kcal/kg
Description : Bed pressure drop in an air fluidised bed of catalyst particles (ρp = 200 kg/m3, Dp = 0.05 cm) of 60 cm bed depth and bed porosity of 0.5 expressed in cm of water (manometer) is (A) 90 (B) 60 (C) 45 (D) 30
Last Answer : (B) 60
Description : In a tension test, the yield stress is 300 kg/cm2 , in the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm (D) 250 kg/cm2
Last Answer : (A) 100 kg/cm2
Description : The principal stresses at a point are 100, 100 and -200 kgf/cm2 , the octahedral shear stress at the point is: (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm2
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2
Last Answer : (D) 300 kg/cm2