Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Pick up the correct statement from the following:
(A) Plain cement concrete is equally strong in compression as well as in tension
(B) Slump test is performed to check concrete strength
(C) Curing of concrete is done for proper compaction of cement
(D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine
aggregates
by

1 Answer

Answer :

Option D
by

Related questions

Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Description : Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Last Answer : Answer: Option B

Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse aggregate should not exceed one fifty of the minimum dimension of the reinforced concrete member (c)The aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Description : Which of the following statement is correct (a) The maximum size of coarse aggregate should not exceed one fourth of the minimum dimension of the plain concrete member. (b) The maximum size of coarse ... aggregates of 40mm, 20mm and 10mm sizes are commonly used for concrete works (d) All the above

Last Answer : (d) All the above

The factors which effects the design of concrete mix is (a) Fineness modulus (b) Water cement ratio (c) Slump (d) All of these

Description : The factors which effects the design of concrete mix is (a) Fineness modulus (b) Water cement ratio (c) Slump (d) All of these

Last Answer : (d) All of these

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the concrete (C) The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Description : Pick up the correct statement from the following: (A) An increase in water content must be accompanied by an increase in cement content (B) Angular and rough aggregates reduce the workability of the ... The slump of the concrete mix decreases due to an increase in temperature (D) All the above

Last Answer : Answer: Option D

Strength of concrete increases with (A) Increase in water-cement ratio (B) Increase in fineness of cement (C) Decrease in curing time (D) Decrease in size of aggregate

Description : Strength of concrete increases with (A) Increase in water-cement ratio (B) Increase in fineness of cement (C) Decrease in curing time (D) Decrease in size of aggregate

Last Answer : (B) Increase in fineness of cement

If X, Y and Z are the fineness modulli of coarse, fine and combined aggregates, the percentage (P) of fine aggregates to combined aggregates, is (A) P = [(Z - X)/(Z - Y)] × 100 (B) P = [(X - Z)/(Z - Y)] × 100 (C) P = [(X - Z)/(Z + Y)] × 100 (D) P = [(Z + X)/(Z - Y)] × 100

Description : If X, Y and Z are the fineness modulli of coarse, fine and combined aggregates, the percentage (P) of fine aggregates to combined aggregates, is (A) P = [(Z - X)/(Z - Y)] × 100 (B) P = [(X - Z)/(Z - Y)] × 100 (C) P = [(X - Z)/(Z + Y)] × 100 (D) P = [(Z + X)/(Z - Y)] × 100

Last Answer : Option B

C.R.R.I. charts are used to obtain a relationship between strength of concrete and (A) Water cement ratio (B) Workability (C) Grading of aggregate (D) Fineness modulus

Description : C.R.R.I. charts are used to obtain a relationship between strength of concrete and (A) Water cement ratio (B) Workability (C) Grading of aggregate (D) Fineness modulus

Last Answer : Answer: Option A

If fineness modulus of sand is 2.5, it is graded as (A) Very fine sand (B) Fine sand (C) Medium sand (D) Coarse

Description : If fineness modulus of sand is 2.5, it is graded as (A) Very fine sand (B) Fine sand (C) Medium sand (D) Coarse

Last Answer : Answer: Option B

If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Description : If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Last Answer : Answer: Option C

Concrete gains strength due to (A) Chemical reaction of cement with sand and coarse aggregates (B) Evaporation of water from concrete (C) Hydration of cement (D) All the above

Description : Concrete gains strength due to (A) Chemical reaction of cement with sand and coarse aggregates (B) Evaporation of water from concrete (C) Hydration of cement (D) All the above

Last Answer : Answer: Option C

Concrete gains strength due to [ A ] Chemical reaction of cement with sand and coarse aggregates [ B ] Evaporation of water from concrete [ C ] Hydration of cement [ D ] All the above

Description : Concrete gains strength due to [ A ] Chemical reaction of cement with sand and coarse aggregates [ B ] Evaporation of water from concrete [ C ] Hydration of cement [ D ] All the above

Last Answer : [ C ] Hydration of cement

The workability of concrete is expressed by (a) Water-cement ratio (b) Slump value (c) Compaction factor (d) Both (a) and (b)

Description : The workability of concrete is expressed by (a) Water-cement ratio (b) Slump value (c) Compaction factor (d) Both (a) and (b)

Last Answer : (d) Both (a) and (b)

For preparing a test-specimen, it is necessary (A) To mix cement and fine aggregate by dry hand (B) To mix coarse aggregates (C) To mix water to the cement, fine aggregates and coarse aggregates (D) All the above

Description : For preparing a test-specimen, it is necessary (A) To mix cement and fine aggregate by dry hand (B) To mix coarse aggregates (C) To mix water to the cement, fine aggregates and coarse aggregates (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Water cement paste hardens due to hydration (B) During hardening cement binds the aggregates together (C) Cement provides strength, durability and water tightness to the concrete (D) All the above

Description : Pick up the correct statement from the following: (A) Water cement paste hardens due to hydration (B) During hardening cement binds the aggregates together (C) Cement provides strength, durability and water tightness to the concrete (D) All the above

Last Answer : Answer: Option D

The produce impermeable concrete (A) Thorough mixing of concrete is required (B) Proper compaction of concrete is required (C) Proper curing of concrete is required (D) All the above

Description : The produce impermeable concrete (A) Thorough mixing of concrete is required (B) Proper compaction of concrete is required (C) Proper curing of concrete is required (D) All the above

Last Answer : Answer: Option D

In the method of voids for determination of the quantity of cement paste, it is assumed that (A) Voids in coarse aggregates are filled by fine aggregates (B) Voids in fine aggregates are filled by the cement paste (C) Volume of fine aggregates is equal to total voids in coarse aggregates plus 10% extra (D) All the above

Description : In the method of voids for determination of the quantity of cement paste, it is assumed that (A) Voids in coarse aggregates are filled by fine aggregates (B) Voids in fine aggregates are filled by ... of fine aggregates is equal to total voids in coarse aggregates plus 10% extra (D) All the above

Last Answer : Answer: Option D

If P, Y and Z are the weights of cement, fine aggregates and coarse aggregates respectively and W/C is the water cement ratio, the minimum quantity of water to be added to first batch, is obtained by the equation (A) 0.1P + 0.3Y + 0.1Z = W/C × P (B) 0.3P + 0.1Y + 0.01Z = W/C × P (C) 0.4P + 0.2Y + 0.01Z = W/C × P (D) 0.5P + 0.3Y + 0.01Z = W/C × P

Description : If P, Y and Z are the weights of cement, fine aggregates and coarse aggregates respectively and W/C is the water cement ratio, the minimum quantity of water to be added to first batch, is obtained by the equation (A) 0.1P + 0.3Y + 0. ... + 0.2Y + 0.01Z = W/C P (D) 0.5P + 0.3Y + 0.01Z = W/C P

Last Answer : Answer: Option B

Pick up the correct assumption of the theory of simple bending (A) The value of the Young's modulus is the same in tension as well as in compression (B) Transverse section of a beam remains plane before and after bending (C) The material of the beam is homogeneous and isotropic (D) All the above

Description : Pick up the correct assumption of the theory of simple bending  (A) The value of the Young's modulus is the same in tension as well as in compression  (B) Transverse section of a beam remains ... bending  (C) The material of the beam is homogeneous and isotropic  (D) All the above

Last Answer : (D) All the above

Internal friction between the ingredients of concrete, is decreased by using (A) Less water (B) Fine aggregates (C) Rich mix (D) More water and coarse aggregates

Description : Internal friction between the ingredients of concrete, is decreased by using (A) Less water (B) Fine aggregates (C) Rich mix (D) More water and coarse aggregates

Last Answer : Answer: Option D

For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Description : For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Last Answer : (a) Triaxial compression test

If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, 6 kg, 4 kg respectively, the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45

Last Answer : Answer: Option C

Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Description : Workability of a concrete – mix is determined by (i)Slump cone test (ii)Compaction factor test (iii)Vee bee test [ A ] i [ B ] ii [ C ] i and ii [ D ] i, ii and iii

Last Answer : [ D ] i, ii and iii

While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Description : While determining the workability of concrete mix, the compaction factor test is ------than the slump cone test [ A ] Less accurate [ B ] More accurate [ C ] Approximate method [ D ] None of the above

Last Answer : [ B ] More accurate

Modulus of elasticity of concrete is primarily influenced by [ A ] Elastic properties of aggregate [ B ] Curing of concrete [ C ] Age of concrete [ D ] Mix proportion and type of cement

Description : Modulus of elasticity of concrete is primarily influenced by [ A ] Elastic properties of aggregate [ B ] Curing of concrete [ C ] Age of concrete [ D ] Mix proportion and type of cement

Last Answer : [ A ] Elastic properties of aggregate

Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Description : Pick up the correct statement from the following: (A) The weight of ingredients of concrete mix, is taken in kilograms (B) Water and aggregates are measured in litres (C) 20 bags of cement make one tonne (D) All the above

Last Answer : Answer: Option D

Too much fineness of cement (a) Results cracks in concrete (b) Generates greater heat (c) Develops later strength (d) All the above

Description : Too much fineness of cement (a) Results cracks in concrete (b) Generates greater heat (c) Develops later strength (d) All the above

Last Answer : (d) All the above

If th fineness modules of sand is 3, then the sand is graded as (a) Very fine sand (b) Fine sand (c)Medium sand (d) Coarse sand

Description : If th fineness modules of sand is 3, then the sand is graded as (a) Very fine sand (b) Fine sand (c)Medium sand (d) Coarse sand

Last Answer : (d) Coarse sand

Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d

Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d

Last Answer : (A) h = 0.4 d

Pick up the correct statement from the following: (A) The dry density reduces by addition of water after attaining optimum moisture content (B) The line joining the peak of three moisture content graphs obtained by using three compactive energies, is called line of optimus (C) Well graded coarse grained soils can be compacted to a very high density as compared to fine grained soils (D) All the above

Description : Pick up the correct statement from the following: (A) The dry density reduces by addition of water after attaining optimum moisture content (B) The line joining the peak of three moisture content graphs ... be compacted to a very high density as compared to fine grained soils (D) All the above

Last Answer : Answer: Option D

The fineness modulus of fine aggregate is in the range of (A) 2.0 to 3.5 (B) 3.5 to 5.0 (C) 5.0 to 7.0 (D) 6.0 to 8.5

Description : The fineness modulus of fine aggregate is in the range of (A) 2.0 to 3.5 (B) 3.5 to 5.0 (C) 5.0 to 7.0 (D) 6.0 to 8.5

Last Answer : (A) 2.0 to 3.5

I.S. Sieve Nos. 10 mm and 4.75 mm are generally used for grading of (A) Coarse aggregates (B) Fine aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : I.S. Sieve Nos. 10 mm and 4.75 mm are generally used for grading of (A) Coarse aggregates (B) Fine aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Illustrate the effect of properties of coarse aggregates on compressive strength of concrete.

Description : Illustrate the effect of properties of coarse aggregates on compressive strength of concrete.

Last Answer : Effect of properties of coarse aggregates on compressive strength of concrete. i. Size of aggregate: If coarse aggregate particles are of large size (say 20 mm) in concrete mixture , then ... of strength. But if water absorption is less concrete becomes as per proportion giving required strength.

The process of keeping concrete moist for a certain period after its finishing, is known as (A) Finishing of concrete (B) Curing of concrete (C) Placing of concrete (D) Compaction of concrete

Description : The process of keeping concrete moist for a certain period after its finishing, is known as (A) Finishing of concrete (B) Curing of concrete (C) Placing of concrete (D) Compaction of concrete

Last Answer : Answer: Option B

The process of consolidating concrete mix after placing it in position is termed as. (a) Curing (b) Wetting (c) Compaction (d) All of these

Description : The process of consolidating concrete mix after placing it in position is termed as. (a) Curing (b) Wetting (c) Compaction (d) All of these

Last Answer : (c) Compaction

The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Description : The type of aggregates not suitable for high strength concrete and for pavements subjected to tension, is (A) Rounded aggregate (B) Irregular aggregate (C) Angular aggregate (D) Flaky aggregat

Last Answer : Answer: Option A

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Description : Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Last Answer : (c) Tensile, compressive and shear stresses.

For a good concrete (A) Aggregates should be hard and durable (B) Water should be free from organic materials (C) Cement should be sufficient to produce the required strength (D) All the above

Description : For a good concrete (A) Aggregates should be hard and durable (B) Water should be free from organic materials (C) Cement should be sufficient to produce the required strength (D) All the above

Last Answer : Answer: Option D

According to Water-Cement Ratio Law, the strength of workable plastic concrete (A) Depends upon the amount of water used in the mix (B) Does not depend upon the quality of cement mixed with aggregates (C) Does not depend upon the quantity of cement mixed with aggregates (D) All the above

Description : According to Water-Cement Ratio Law, the strength of workable plastic concrete (A) Depends upon the amount of water used in the mix (B) Does not depend upon the quality of cement mixed with aggregates (C) Does not depend upon the quantity of cement mixed with aggregates (D) All the above

Last Answer : Answer: Option D

The maximum amount of dust which may be permitted in aggregates is (A) 5% of the total aggregates for low workability with a coarse grading (B) 10% of the total aggregates for low workability with a fine grading (C) 20% of the total aggregates for a mix having high workability with fine grading (D) All the above

Description : The maximum amount of dust which may be permitted in aggregates is (A) 5% of the total aggregates for low workability with a coarse grading (B) 10% of the total aggregates for low workability with ... of the total aggregates for a mix having high workability with fine grading (D) All the above

Last Answer : Answer: Option D

Concrete is [ A ] Weak in tension [ B ] Strong in tension [ C ] Strong in both tension and compression [ D ] Weak in compression

Description : Concrete is [ A ] Weak in tension [ B ] Strong in tension [ C ] Strong in both tension and compression [ D ] Weak in compression

Last Answer : [ A ] Weak in tension

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

The assumption in the theory of bending of beams is: (A) Material is homogeneous (B) Material is isotropic (C) Young's modulus is same in tension as well as in compression (D) All the above

Description : The assumption in the theory of bending of beams is:  (A) Material is homogeneous  (B) Material is isotropic  (C) Young's modulus is same in tension as well as in compression  (D) All the above 

Last Answer : (D) All the above 

Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above

Description : Pick up the correct statement from the following: (A) Higher workability indicates unexpected increase in the moisture content (B) Higher workability indicates deficiency of sand (C) If the concrete mix is dry, the slump is zero (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) Segregation is necessary for a workable concrete (B) Consistency does not affect the workability of concrete (C) If the concrete mix is dry, the slump is maximum (D) None of these

Description : Pick up the correct statement from the following: (A) Segregation is necessary for a workable concrete (B) Consistency does not affect the workability of concrete (C) If the concrete mix is dry, the slump is maximum (D) None of these

Last Answer : Answer: Option D

In order to prepare a test specimen, it is necessary to (a) Mix the cement and fine aggregate (sand ) dry hand (b) Mix the coarse aggregate (c) Mix water to the cement, fine aggregate and coarse aggregate (d) All of the above

Description : In order to prepare a test specimen, it is necessary to (a) Mix the cement and fine aggregate (sand ) dry hand (b) Mix the coarse aggregate (c) Mix water to the cement, fine aggregate and coarse aggregate (d) All of the above

Last Answer : (d) All of the above

Pick up the incorrect statement from the following: (A) The degree of grinding of cement, is called fineness (B) The process of changing cement paste into hard mass, is known as setting of cement (C) The phenomenon by virtue of which cement does not allow transmission of sound, is known as soundness of cement (D) The heat generated during chemical reaction of cement with water, is known as heat of hydration

Description : Pick up the incorrect statement from the following: (A) The degree of grinding of cement, is called fineness (B) The process of changing cement paste into hard mass, is known as setting of ... (D) The heat generated during chemical reaction of cement with water, is known as heat of hydration

Last Answer : Answer: Option C

Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Description : Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Last Answer : (a) Compressive stress.