The section of the beam having greater width at the top in comparison to the width below neutral axis is known as. (a) Critical section (b) T-section (c) L-section (d) None of these

The section of the beam having greater width at the top in comparison to the width below neutral axis is known as.
(a) Critical section
(b) T-section
(c) L-section
(d) None of these
by

1 Answer

Answer :

(b) T-section
by

Related questions

A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Description : A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis (A) Remains within the flange (B) Remains below the slab (C) Coincides the geometrical centre of the beam (D) None of these

Last Answer : Answer: Option A

The neutral axis of an over –reinforced section falls (a) On the critical neutral axis of balanced section. (b) Below the critical neutral axis of balanced section (c) Above the neutral axis o balanced section (d) Al l the above

Description : The neutral axis of an over –reinforced section falls (a) On the critical neutral axis of balanced section. (b) Below the critical neutral axis of balanced section (c) Above the neutral axis o balanced section (d) Al l the above

Last Answer : (b) Below the critical neutral axis of balanced section

The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio is 18, then the stress developed in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2

Last Answer : (b) 135N/mm2

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

In a doubly-reinforced beam if and is the effective depth and is depth of critical neutral axis, the following relationship holds good (A) mc/t = n/(d - n) (B) (m + c)/t = n/(d + n) (C) (t + c)/n = (d + n)/nD) mc/t = (d - n)/t

Description : In a doubly-reinforced beam if and is the effective depth and is depth of critical neutral axis, the following relationship holds good (A) mc/t = n/(d - n) (B) (m + c)/t = n/(d + n) (C) (t + c)/n = (d + n)/n D) mc/t = (d - n)/t

Last Answer : Answer: Option A

A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange

Description : A beam of T-section is subjected to a shear force of F. The maximum shear force will occur at the a. top of the section b. bottom of the section c. neutral axis of the section d. junction of web and flange

Last Answer : c. neutral axis of the section

The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Description : The depth of neutral axis for a balanced section is --------- the depth of critical neutral axis [ A ] equal [ B ] always greater than [ C ] always less than [ D ] may be sometimes greater than

Last Answer : [ A ] equal

The depth of neutral axis for over reinforced section is ----------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Description : The depth of neutral axis for over reinforced section is ----------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Last Answer : [ B ] Greater than

The depth of neutral axis for under reinforced section is --------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Description : The depth of neutral axis for under reinforced section is --------- the depth of critical neutral axis [ A ] Equal to [ B ] Greater than [ C ] Less than [ D ] None of the above

Last Answer : [ C ] Less than

For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Description : For a reinforced concrete beam section, the shape of shear stress diagram is (a) Parabolic over the whole section with maximum value at the neutral axis. (b) Parabolic above the neutral axis and rectangular below the neutral axis. (c) Linearly varying as the distance form the N.A. (d) All the above.

Last Answer : (b) Parabolic above the neutral axis and rectangular below the neutral axis.

The neutral axis in a T-beam section falls (a) Within the flange (b) Outside the flange (c) Either (a) or (b) (d) All the above

Description : The neutral axis in a T-beam section falls (a) Within the flange (b) Outside the flange (c) Either (a) or (b) (d) All the above

Last Answer : (c) Either (a) or (b)

The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these

Description : The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these

Last Answer : (A) Pass through the centroid of the section

When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section

Last Answer : (B) Top fibre

The neutral axis of a T-beam exists (A) Within the flange (B) At the bottom edge of the slab (C) Below the slab (D) All the above

Description : The neutral axis of a T-beam exists (A) Within the flange (B) At the bottom edge of the slab (C) Below the slab (D) All the above

Last Answer : Answer: Option D

The actual neutral axis of n under reinforced section is above the critical neutral axis of a balanced section (a) Correct (b) Incorrect (c) Not known (d) None of these

Description : The actual neutral axis of n under reinforced section is above the critical neutral axis of a balanced section (a) Correct (b) Incorrect (c) Not known (d) None of these

Last Answer : (a) Correct

A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is (A) [m/(m - r)] d (B) [m/(m + r)] d (C) [(m + r)/m] d (D) [(r - m)/m] d

Description : If the modular ratio is , steel ratio is and overall depth of a beam is , the depth of the critical neutral axis of the beam, is (A) [m/(m - r)] d (B) [m/(m + r)] d (C) [(m + r)/m] d (D) [(r - m)/m] d

Last Answer : Answer: Option B

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D

If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Description : If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called (A) Balanced beam (B) Under-reinforced beam (C) Over-reinforced beam (D) None of the above

Last Answer : Option C

The neutral axis of a balanced section is called (a) Balanced neutral axis (b) Critical neutral axis (c) Equivalent neutral axis (d) All of these

Description : The neutral axis of a balanced section is called (a) Balanced neutral axis (b) Critical neutral axis (c) Equivalent neutral axis (d) All of these

Last Answer : (b) Critical neutral axis

The neutral axis corresponding to balanced section condition is termed as [ A ] Critical neutral axis [ B ] Centroidal neutral axis [ C ] Balanced neutral axis [ D ] All the above

Description : The neutral axis corresponding to balanced section condition is termed as [ A ] Critical neutral axis [ B ] Centroidal neutral axis [ C ] Balanced neutral axis [ D ] All the above

Last Answer : [ A ] Critical neutral axis

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment(B) In a loaded beam, the moment at which the entire section of the beam becomes fully plastic, is called plastic moment (C) In a fully plastic stage of the beam, the neutral axis divides the section in two sections of equal area (D) All the above

Description : Pick up the correct statement from the following:  (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of  equal area  (D) All the above 

Last Answer : (D) All the above 

The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Description : The shear force on a simply supported beam is proportional to (A) Displacement of the neutral axis (B) Sum of the forces (C) Sum of the transverse forces (D) Algebraic sum of the transverse forces of the section

Last Answer : (D) Algebraic sum of the transverse forces of the section

Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section (C) Distance of the C.G. of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Last Answer : Answer: Option D

If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Description : If the depth of actual neutral axis is greater than the depth of critical neutral axis, then [ A ] Concrete attains its permissible stress earlier [ B ] Steel attains its permissible stress earlier [ C ] Both concrete and steel reaches its permissible stresses simultaneously [ D ] None of the above

Last Answer : [ A ] Concrete attains its permissible stress earlier

Diagonal tension in a beam (A) Is maximum at neutral axis (B) Decreases below the neutral axis and increases above the neutral axis (C) Increases below the neutral axis and decreases above the neutral axis (D) Remains same

Description : Diagonal tension in a beam (A) Is maximum at neutral axis (B) Decreases below the neutral axis and increases above the neutral axis (C) Increases below the neutral axis and decreases above the neutral axis (D) Remains same

Last Answer : Answer: Option C

A reinforced concrete beam will crack if tensile stress set up in the concrete below the neutral axis is (a) More than the permissible stress (b) Less than the permissible stress (c) Equal to the permissible stress (d) All the above.

Description : A reinforced concrete beam will crack if tensile stress set up in the concrete below the neutral axis is (a) More than the permissible stress (b) Less than the permissible stress (c) Equal to the permissible stress (d) All the above.

Last Answer : (a) More than the permissible stress

If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Description : If the load on beam is increased, the tensile stress sin the concrete below the neutral axis will (a) Increase (b) Decrease (c) Remain unchanged (d) None of these

Last Answer : (a) Increase

In case of a cantilever beam , the tensile zone is D. (a) Above the neutral axis (b) Below the neutralaxis (c) At the neutral axis (d) All the above

Description : In case of a cantilever beam , the tensile zone is D. (a) Above the neutral axis (b) Below the neutralaxis (c) At the neutral axis (d) All the above

Last Answer : (a) Above the neutral axis

In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these

Last Answer : (b) Below the neutral axis

An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity of shear stress, is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2

Last Answer : Answer: Option A

An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is (A) Safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section

Last Answer : Answer: Option A

The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is(A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Description : The maximum compressive stress at the top of a beam is 1600 kg/cm2 and the corresponding tensile stress at its bottom is 400 kg/cm2 . If the depth of the beam is 10 cm, the neutral axis from the top, is (A) 2 cm (B) 4 cm (C) 6 cm (D) 8 cm

Last Answer : (D) 8 cm

An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis

Description : An increase in temperature on the top fibre of a simply supported beam will cause (a) Downward deflection (b) Upward deflection (c) No deflection (d) Angular rotation about neutral axis

Last Answer : Upward deflection

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Description : For a reinforced concrete section, the shape of shear stress diagram is (A) Wholly parabolic (B) Wholly rectangular (C) Parabolic above neutral axis and rectangular below neutral axis (D) Rectangular above neutral axis and parabolic below neutral axis

Last Answer : Answer: Option C

With usual notations the depth of the neutral axis of a balanced section, is given by (A) mc/t = (d - n)/n (B) t/mc = (d - n)/n (C) t/mc = (d + n)/n (D) mc/t = n/(d - n)

Description : With usual notations the depth of the neutral axis of a balanced section, is given by (A) mc/t = (d - n)/n (B) t/mc = (d - n)/n (C) t/mc = (d + n)/n (D) mc/t = n/(d - n)

Last Answer : Answer: Option D

What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Description : What is the shear stress acting along the neutral axis of triangular beam section, with base 60 mm and height 150 mm, when shear force of 30 kN acts? a. 15.36 N/mm2 b. 10.6 N/mm2 c. 8.88 N/mm2 d. Insufficient data

Last Answer : c. 8.88 N/mm2

The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Description : The width of a beam of uniform strength having a constant depth d length L, simply supported at the ends with a central load W is (A) 2WL/3fd² (B) 3WL/2fd² (C) 2fL/3Wd 4 (D) 3fL²/2Wd

Last Answer : (B) 3WL/2fd²

If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t

Last Answer : Answer: Option D

If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Description : If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is (A) 37 cm (B) 38 cm (C) 39 cm (D) 40 cm

Last Answer : Answer: Option D

If is the shear force at a section of an I-joist, having web depth and moment of inertia about its neutral axis, the difference between the maximum and mean shear stresses in the web is, (A) Sd²/8I (B) Sd²/12I (C) Sd²/16I(D) Sd²/24I

Description : If is the shear force at a section of an I-joist, having web depth and moment of inertia about its neutral axis, the difference between the maximum and mean shear stresses in the web is, (A) Sd²/8I (B) Sd²/12I (C) Sd²/16I (D) Sd²/24I

Last Answer : (D) Sd²/24I

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Description : An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2 , the beam (A) Is safe in shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined bars (D) Needs revision of section

Last Answer : Answer: Option D

If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is increased by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Description : If the tendon is placed at an eccentricity e below the centroidal axis of the longitudinal axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge (A) Is ... by PZ/e (B) Is increased by Pe/Z (C) Is decreased by Pe/Z (D) Remains unchanged

Last Answer : Answer: Option C

When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Description : When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Last Answer : (b) Bottom fibre

Pick up the correct statement from the following: (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres (B) The shear stress is zero at the outer fibres and maximum at the neutral axis (C) The bending stress at the outer fibres, is known as principal stress (D) All the above

Description : Pick up the correct statement from the following:  (A) The bending stress in a section is zero at its neutral axis and maximum at the outer fibres  (B) The shear stress is zero at the outer ... (C) The bending stress at the outer fibres, is known as principal stress  (D) All the above 

Last Answer : (D) All the above 

Along the neutral axis of a simply supported beam (A) Fibres do not undergo strain (B) Fibres undergo minimum strain (C) Fibres undergo maximum strain (D) None of these

Description : Along the neutral axis of a simply supported beam  (A) Fibres do not undergo strain  (B) Fibres undergo minimum strain  (C) Fibres undergo maximum strain  (D) None of these

Last Answer : (A) Fibres do not undergo strain 

In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis

Last Answer : Answer: Option B